Set A only Problem No. 1.: All bars in the truss shown are 25-mm diameter steelrods (E = 200 GPa).%3DP1, kN150SETP2, kNL1, meterL2, meter | L3, meterA1001.01.51.2В160851.21.51.5C180701.51.51.2Set A: Determine the elongation at bar AB and bar BE.P1BP2L1DEL2L3Figure for Problem No. 1

Answered: Image /qna-images/answer/4a500dfd-1db4-44e1-800c-bdad614d8b98.jpg

Problem No. 1.: All bars in the truss shown are 25-mm diameter steel rods (E = 200 GPa). L1, meter L2, meter | L3, meter P1, kN 150 SET Р2, kN A 100 1.0 1.5 1.2 В 160 85 70 1.2 1.5 1.5 1.5 1.2 C 180 1.5 Set A: Determine the elongation at bar AB and bar BE. P1 P2 L1 D L2 L3 Figure for Problem No. 1

Problem No. 1.: All bars in the truss shown are 25-mm diameter steel rods (E = 200 GPa). L1, meter L2, meter | L3, meter P1, kN 150 SET Р2, kN A 100 1.0 1.5 1.2 В 160 85 70 1.2 1.5 1.5 1.5 1.2 C 180 1.5 Set A: Determine the elongation at bar AB and bar BE. P1 P2 L1 D L2 L3 Figure for Problem No. 1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For 10 to 12. The compound bar ABCD has a uniform cross-sectional area of 0.25 in². When the axial force P is applied, the length of the bar is reduced by 0.018 in. The moduli of elasticity are 29 x 106 psi for steel and 10 x 10 psi for aluminum. 18 in. 6 in. 18 in. P. P Steel B C Steel D -Aluminum 10. What is p? 11. What is the total elongation of the two steel sections? 12. What is the elongation of the aluminum section?
Calculate the change in dimensions in the bar.F = 12000 N; h= 0.01 m; w= 0.03 m; L = 0.8 m; E = 60 GPa; v = 0.3
Answers are already given. Kindly answer all the required forces. ANSWER: FFG=1103.7267 kip, T W= 832. 7498 kip, T Mc= 6272.9979 kip-ft, clockwise Cx= 0 Cy=1297.7498
TASK A hydraulic cylinder with a bore radius of 100 mm and an outer radius of 200 mm has been designed to withstand a maximum internal pressure of 200 MPa in service. During operation, the pressure within the cylinder is retained by a freely sliding piston. The steel used in the manufacture has Young's modulus of 210 GNm-². Note: There is no axial stress generated in the cylinder wall in this application. 1. Elastic Stress Distributions in a Single Cylinder a) At an operating pressure of 200 MPa, calculate using Lame's equations the radial and circumferential stresses at the cylinder bore and the outer surface. Graphically present (sketch) the general form of variation of each of these stresses across the cylinder wall, clearly indicating the calculated values at the cylinder bore and at the outer surface.
A steel rod is stretched between two walls. At 20C, the tensile force in the rod is 5000N. If the stress is not to exceed 130MPa at -20C, find the minimum allowable diameter of the rod. Use a=11.17x10^-6C and E=200GPa. -Draw and label the diagram correctly, No diagram in the solution will be marked wrong. -Shortcut solution will be marked wrong. -Show complete solution and explanation
Required information Members AB and BE of the truss shown consist of 25-mm-diameter steel rods (E= 200 GPa). It is given that P= 69 kN. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. | 150 kN A B 0.9 m D 1.2 m 2 m Determine the elongation of rod BE. The elongation of rod BE is mm
32. A 274-N plank, of length L = 6.23 m, rests on the ground and on a frictionless roller at the top of a wall of height
Let's considera rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E= 200 Gpa and a Poisson's ratio of 0.3. If a tensile force Fis subjected to that rod cross-section, the diameter becomes 3.995 mm. determine the applied force F Select one: OF 5236 N O F=15708 N Clear mopshoe Finish attempt
If a solid circular rod having an initial diameter D = 0.03 m and initial length L = 0.8 m, is subjected to a tensile force F = 300 kN, the new diameter will be: Given: The rod is made of steel having Young's modulus E = 200 Gpa and a Poisson's ratio = 0.3. Select one: a. Df= 2.993 mm Ob. Df = 10.92 mm Oc. Df= 3.007 mm Od. Df = 30.02 mm Oe. Df = 29.98 mm
A diagonal aluminum alloy tension rod of diameter d and initial length I is used in a rectangular frame to prevent collapse. The rod can safely support a tensile stress of oallow. If d = 0.5 in, / = 8 ft, and oallow = 20 kpsi, determine how much the rod must be stretched to develop this allowable stress.
We will use both shearing and bearing analysis to determine the quantities of rivets needed to fasten BC and BE. We can determine two values then choose what will be more safe. ■ For Member BC: ■ Based on Shearing: V T == ■ Av Based on Bearing: P Ab 70MPa = 96000 N .n. (19) ²x n 1/4. π n = 4.84 5 rivets 96000 N (19mm) (6mm) xn 140MPa n = 46.015≈ 7 rivets For member BC, we must use 7 rivets since we must need a minimum of 7 rivets to resist bearing stress produced by the connection. If we only use 5 rivets, then the bearing stress will become 168.42 MPa. It will result to failure since the allowable bearing stress is only 140 Mpa. ■ For member BE: (Practice at Home) Pac EXAMPLE: 5. The figure shows a roof truss and the detail of the riveted connection at joint B. Using allowable stresses of t = 70 MPa and ob= 140 MPa, how many 19-mm diameter rivets are required to fasten member BC to the gusset plate? Member BE? What is the largest average tensile or compressive stress in BC and BE? Say…
A steel rod is stretched between two walls. At 20C, the tensile force in the rod is 5000N. If the stress is not to exceed 130MPa at -20C, find the minimum allowable diameter of the rod. Use a=11.17x10^-6C and E=200GPa. -Draw and label the diagram correctly, No diagram in the solution will be marked wrong. -Shortcut solution will be marked wrong.- Direction of the assumption of the equilibrium equation must be shown, no direction will be marked wrong. -Show complete solution and explanation