Problem Five Consider a serial port operating with a baud rate of 10,000 bits per second. Draw the waveform occurring at the UOTX output (voltage levels are +3.3 and 0) when the ASCII 'a' (0x61) is transmitted on UARTO. The protocol is I start, 8 data and 1 stop bit. UARTO is initially idle, and the software writes the 0x61 to UARTO DR_R at time=0. Show the UOTX line before and after the frame, assuming the channel is idle before and after the frame.

Problem Five Consider a serial port operating with a baud rate of 10,000 bits per second. Draw the waveform occurring at the UOTX output (voltage levels are +3.3 and 0) when the ASCII 'a' (0x61) is transmitted on UARTO. The protocol is I start, 8 data and 1 stop bit. UARTO is initially idle, and the software writes the 0x61 to UARTO DR_R at time=0. Show the UOTX line before and after the frame, assuming the channel is idle before and after the frame.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Write an 8051 microcontroller C program to transfer the message “STOP” serially and continuously at 2400 baud rate. Use 8 bit data and 1 stop bit. With flow chart.
Computer Science Write a C program for the ATmega328PB that continuously toggles bits 1, 3 and 6 of Port B every 250 ms without impacting the other bits of Port B. Initialize bits 1, 3 and 6 to values the of 0, 1 and 0, respectively.
The ATmega32 is used to flash two separate LEDS. as follows: LED D1 will flash on a frequency 20 kHz and duty cycle of 70%. LED D2 will flash on a frequency of 10 kHz and duty cycle of 35%. Develop a C-code to program this ATmega. 22 23 24 25 26 27 28 29 RESET PCO/SCL PC1/SDA PC2/TCK D2 13 12 XTAL1 XTAL2 PC3/TMS PC4/TDO PC5/TDI 40 39 38 37 36 35 34 33 LED PAO/ADCO PA1/ADC1 PA2/ADC2 PA3/ADC3 PAAIADC4 D1 PC6/TOSC1 PC7/TOSC2 14 15 16 17 18 19 20 21 PDO/RXD LED PAS/ADC5 PAGIADC6 PATIADC7 PD1/TXD PD2/INTO PD3/INT1 PD4/OC1B PD5/OC1A PD6ICP1 PD7/OC2 PBOTOXCK PB1/T1 PB2/AINOINT2 4. PB3/AIN1/OCO PB4/SS PB5/MOSI 7. PB6/MISO AREF AVCC 32 30 PB7/SCK ATMEGA32
5- A synchronous TDM with four 2 Mbps data stream inputs and one data stream output. The multiplexing unit of data is 1 bit. The input bit duration is the output bit duration is the output frame rate is ------- Frame/sec. otansmi Mbps; and us; the output bit rate is natos imeni adi stonl -.oi mibanaine 1. 1. ... 2 Mbps Be eill Frames ilsbit ... 0. 2 Mbps MUX 2 Mbps 1. 1. ... 2 Mbps .. 7- A de pulse train has a peak voltage value of 5 V, a frequency of 4 MHz, and a duty cycle of 30 percent. The minimum bandwidth necessary to pass this signal without excessive distortion is MHz. (Note: to =T*Duty Cycle; T= 1/F) 8- Ten channels, each with a 200 kHz bandwidth, are to be multiplexed together using FDM. The minimum bandwidth of the link is need for a guard band of 10 k Hz between the channels; while the minimum bandwidth of the link is 20 kHz between the channels. KHz when there is a KHz when there is a need for a guard band of 9. If a channel can transmit a range of frequencies from 10 MHz…
Write a C-code that initialize the serial port of ATmega16 to baud rate of 1200 bps, no parity, 1 stop bit, 8 data bits. Assume the clock speed is 1 MHz?
Write a program for the MSP-430 FR 6989 Eval board with the attached IR-board that broadcasts a medium long message (30-50 chars) through the IR transceiver.
If a PPI was configured in the combined mode: PortA- mode2 and PortB- mode1, the bits of upper port C will act as?
8.- Write a C function to output 4V in the RC1 pin using a PWM signal at 1 kHZ. Consider a Fosc = 8 MHz. (Assume that the RC1 pin is already configured). Consider a power supply (Vcc) for the MCỦ of 5V.
Explain the double handshake data transfer method in Programmable Peripheral Interface 8255 with a suitable waveform. Also explain the operation performed by 8255 if RD’ = 0, WR’ = 1, CS' = 0, A0 = 0 and A1 = 1. Your explanation must also include the possible control word required to configure the ports of 8255 to perform this operation.
8086 circuit, assume that the connection of ports A and B is as follows. An information parallel to Port A, or input is provided using the push button. 74LS47 (BCD->display converter) to port B) connected, 7-segment display is placed at the output of the converter. From the A-g inputs of the display characters are created by giving the corresponding led light on the display, whichever is 1. 74LS47 received from Port B binary information provides a conversion to show the correct number on the display(For addresses of ports a and b. By dividing the number consisting of the values (in this order) found in d0, d2, d4 and d6 from the information in Port A by two enter the code showing the result in the range 0-F on the display (if the result is two digits, one digit).
Write an ALP for the following scenario: Get an 8 bit data "X" from port P0 and another 8 bit data "Y" from port P1. Perform "X+Y" and send the result through serial port at 9600 baud rate for 20 Times.
a)Write a complete program for the PIC16F84A, with circuit connection as shown in Figure 1(a),so that it flashes the LEDs connected to Port B continuously, in the following patterns:00000000, 00000001, 00000010, 00000100, 00001000, 00010000, 00100000, 01000000,10000000 one after the other with a delay of 1 s inserted between each change of pattern. Use alook-up table to run through the patterns. [Notes: Assume 1s delay subroutine is given. You do not need to write the 1 s delay subroutine] (b) Write a complete program for the PIC16F84A to store even numbers starting from zero inmemory locations 10H to 4FH. For example, 10H should contain 0H, 11H should contain 02H,12H should contain 04H and so on.