Problem 9-65: The thin-walled pipe has an inner diameter of 0.5 in. and a thickness of 0.025 in. If it is subjected to an internal pressure of 500 psi and the axial tension and torsional loadings shown, determine the principal stress at a point on the surface of the pipe. 200 lb 200 lb 20 lb-ft 20 lb-ft

Problem 9-65: The thin-walled pipe has an inner diameter of 0.5 in. and a thickness of 0.025 in. If it is subjected to an internal pressure of 500 psi and the axial tension and torsional loadings shown, determine the principal stress at a point on the surface of the pipe. 200 lb 200 lb 20 lb-ft 20 lb-ft

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

roblem The two members are connected by two 20-mm bolts. If P = 10 kN, determine the normal and shear stresses in the bolts and the maximum bearing stress on the member. The nuts have an outer diameter of 30 mm. P P Guides to solve the problem: 12 mm Front view: 30° 1. Draw the FBD of one member. 2. Solve for the bearing force. 3. Section one bolt and solve internal forces. 4. Solve for the normal and shear stress in the bolts. 5. Solve for the bearing stress in the members due to the nuts. 6. Solve for the bearing stress in the members due to the bolts. 36 mm 36 mm P P
The A-36 steel pipe in (Figure 1) has a 6061-T6 aluminum core. It is subjected to a tensile force of 200 kN. The pipe has an outer diameter of 65 mm and an inner diameter of 55 mm. For A-36 steel, Est = 200 GPa, and for 6061-T6 aluminum, E = 68.9 GPa. Determine the average normal stress in the aluminum due to this loading. Express your answer to three significant figures and include appropriate units. ? Oal = Value Units Submit Request Answer Part B Determine the average normal stress in the steel due to this loading. Express your answer to three significant figures and include appropriate units. ? Figure 1 of 1 Value Units Ost = 400 mm Submit Request Answer 200 kN 200 kN
A pipe carrying steam at 3.5 MPa has an outside diameter of 450 mm and a wall thickness of 10 mm. A gasket is inserted between the flange at one end of the pipe and a flat plate used to cap the end. How many 40-mm-diameter bolts must be used to hold the cap on if the allowable stress in the bolts is 105 MPa, of which 55 MPa is the initial stress? What circumferential stress is developed in the pipe? Why is it necessary to tighten the bolt initially, and what will happen if the steam pressure should cause the stress in the bolts to be twice the value of the initial stress? *
The 53kg girl shown is doing a chin-up. For the position shown, the humerous is modelled as an axially loaded member. Determine the normal stress (in MPa) at section a-a if the section is modelled as a hollow cylinder of outside diameter 22.4mm and inside diameter 15.2mm. Note: Do NOT include units in your answer a-+-a (а) (b) Answer:
The steel pipe in (Figure 1) has an inner diameter of 3.41 in and an outer diameter of 3.66 in. If it is fixed at C and subjected to the horizontal 60-lb force acting on the handle of the pipe wrench at its end, determine the principal stresses in the pipe at point A, which is located on the outer surface of the pipe.
4. The steel water pipe has an inner diameter of 100 mm and wall thickness 5 mm. If the flow of water within the pipe in Figure 4 is stopped due to the closing of a valve, determine the longitudinal and hoop stress developed at point A. Draw the state of stress on a volume element located on the wall A. 5 mm valve AI pressure 0.5 Mpa 50 mm Figure 4
Solve the problems below: 1. The link acts as part of the elevator control for a small airplane. If the attached aluminum tube has an inner diameter of 25 mm and a wall thickness of 5 mm, determine the maximum shear stress in the tube when the cable force of 600 N is applied to the cables. 600 N 75 mm 5 mm 75 mm -25 mm 600 N
Problem 2: For the shaft shown below, determine the normal and shear stresses acting on the element located at point A, including stress concentrations. Then draw the stress element at A with the applied stresses and determine the three principal stress (0₁, 02 and, 03) using Mohr's circle. r= 0.0042 m, d = 0.03 m, D = 0.033 m, T= 250 Nm P = 1500 N, M = 300 Nm, A M T J.C₁ P r M T Di d
A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 30 mm. The outer diamter and thickness of the pressure vessel is 500 mm and 10 mm. Its length is 2m. Determine the maximum internal pressure (MPa) that can be applied if the longitudinal stress is limited to 155 MPa, and the circumferencial stress is limited to 55 MPa.
Determine the normal stress in each section of the assembly. The diameter of the solid shaft of each section is 0.50 inches. Give the answer in Ib/in?. Assume Point A is a fixed support and the block at A is rigid. Indicate if it is in tension or compression. 3.50 kip 1.75 kip 5.00 kip B 3.50 kip A 1.75 kip 18 in. 12 in.- 16 in: CAR = units %3D II
A simple pin-connected truss is loaded and supported as shown. All members of the truss are aluminum pipes that have an outside diameter of 70 mm and a wall thickness of 3 mm. Determine the normal stress in each truss member. Assume P-12 kN, Q - 17 kN, a- 1.4 m, b -3.6 m, and c-1.3 m. Use positive for tensile stress and negative for compressive stress. Answers: OAB- JAC- OBC- i B (3) b MPa. MPa. MPa.
For the pin connection shown, determine the normal stress acting on the gross area, the normal stress acting on the net area, the shear stress in the pin, and the bearing stress in the steel plate at the pin.