PROBLEM 3. The aluminum rod has asolid circular cross-section and supportsthe loading shown. Drawing the nomalforce diagram and keeping the weightminimum, detemine the diameter of therod at each segment AB, BC, CD and DE.Compare the weight of the rod if themagnesium alloy AZ91D was used as therod material.8 kN4 kN6 kN2 kN-4 m-2 m--2 m

Answered: Image /qna-images/answer/b18db706-cac6-4247-a290-cedb9e80cd62.jpg

PROBLEM 3. The aluminum rod has a solid circular cross-section and supports the loading shown. Drawing the normal force diagram and keeping the weight minimum, determine the diameter of the rod at each segment AB, BC, CD and DE. Compare the weight of the rod if the magnesium alloy AZ91D was used as the 8 kN 4 m 4 kN 6 kN 2m -2 m 2 kN 2 m

PROBLEM 3. The aluminum rod has a solid circular cross-section and supports the loading shown. Drawing the normal force diagram and keeping the weight minimum, determine the diameter of the rod at each segment AB, BC, CD and DE. Compare the weight of the rod if the magnesium alloy AZ91D was used as the 8 kN 4 m 4 kN 6 kN 2m -2 m 2 kN 2 m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.3.7P: -7 Repeat Problem 2.3-5, but n include the weight of the bar. See Table I-I in Appendix I for the...

See similar textbooks

Similar questions

Created from steel and brassgraded Rod, two at each endplaced between the fixed wall, B60kN respectively from and D pointsand 40kn axial forceswere exposed. Accordinglysteel (Eçelik=200GPa andEpirus=105GPa) formed in ricemaximum stressescalculate.
plz help before -ront The shaft is supported at its ends by two bearings A and B and is subjected to the forces applied to the pulleys fixed to the shaft. (Figure 1) The T₁ 410-N forces act in the - direction and the 200-N and 80-N forces act in the +y direction. The journal bearings at A and B exert only y and components of force on the shaft. Figure lashel but sol is 300 mm A 200 mm 2 150 mm 150 mm ✓ 200 mm 400 mm B. 200 N 200 N 80 N 80 N 1 of 1 ▾ Part B Determine the resultant shear force in the y direction on the cross section at C Express your answer to three significant figures and include appropriate units. (Vc)y=245.714 Submit Part C Submit * Incorrect; Try Again; 3 attempts remaining Check your signs. (Vc),= 175 ▾ Part D Determine the resultant shear force in the direction on the cross section at C. Express your answer to three significant figures and include appropriate unite. T= 10 ▾ Part E Previous Answere (Mc) Submit M ^ Part Fi * Incorrect; Try Again; 5 attempts remaining…
The 20 mm diameter steel shaft AB is attached into the rigid wall at B and supported by a smooth bearing at A. The lever AC is welded to the end of the shaft. If the downward force P will produce a 50 mm vertical displacement at the free end of lever AC, determine the force P if G = 83 GPa.
Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
The cylindrical steel column has an outer diameter of 4 in. and inner diameter of 3.5 in. The column is separated from the concrete foundation by a square bearing plate. The working compressive stress is 26 000 psi for the column, and the working bearing stress is 1200 psi for concrete. Find the largest force P that can be applied to the column. Express your answer in Ib. 4 in. 3.5 in. 4/4 7 in.
three (3) different cylinder mude from Steel, Aliminurn and Uronze are jointed Logether to torma composite structure and fixed to vall suport. Three (3) axial forces acted on the structure as shown. The fallowing valuc was alroady cietermined: 1 KN to the nght -3kN Tensioa -2 kN compression Reaction al A Internal force for Aluminum Interral force for Brone Este= 200 GPa; Ealumin 70 GPa Egmee 83 GPa Determine Ue eiongalion (A) for ach section: Steel Aluminum Bronve Aluminum A= 400 mm Bronze A-200 mm Steel A S00 m 2P 4P SP 2.5 m 2.0 m 1.5 m
d = 30 mm diameter, solid, ductile no.11 m from end A of vertical shaft AB made of materialtightly fitted to a radius disc, at end B to the groundfixed. From the C point of the disk - parallel to the y axisA force of F = 20 kN will be applied. Safety of the shaftcontrol according to Tresca criterion and Von-Mises criteriondo. (Due to the tight fit, the shaft is in the hole in the disc.cannot rotate freely.)
The rigid bar of negligible mass, pinned at one end, is supported by a steel rod and aluminum rod asshown. What maximum load P can be applied without exceeding stress in the steel of 130MN/m2or in the aluminum of 90MN/m2
A hand compactor is composed of a strong rigid arm ABC pinned at B and pin connected link CD. It is designed such that link CD will fail if the compactor is overloaded since CD is easily replaceable. The design is such that when portion AB is horizontal at the bottom of its stroke then theta = 45 degrees. If link CD is 4 mm diameter A36 mild steel determine the largest compaction force that can be developed and the hand force P required with a 1.5 Factor of Safety.
Snap fits are commonly used to lock plastic parts together. A design for a torsional snap- fit is shown. The rod ABC is fixed at both ends and a tab is attached to the rod pivots under the action of forces shown. The rod diameter is 7mm and G-4 GPa. Treat the tabs as rigid. Li-60mm, L2-40mm, w-30mm. (a) Determine the rotation of the cross-section B and the displacement of end D if the force F-8N. (b) Determine the maximum shear stress in the rod (Note: the latter two diagrams are to help you conceptualize.) DE W В THE F Tc ТА A Tо
The wing spar ABD of a light plane is made from 2014-T6 aluminum and has a cross- sectional area of 800 mm², a height of 79 mm, and a moment of inertia about its neutral axis of 1.07(106) mª. Assume A, B, and C' are pins. The neutral axis passes through the cross-section at half of its height. Connection is made along the central longitudinal axis of the spar. The anticipated loading is to be as shown. (Figure 1) Determine the absolute maximum bending stress in the spar. 0.6 m 14.4 kN/m 0.9 m B -1.8 m-
A11 Estimate the matrix of the structure to solve with the method of knots. Determine the stresses in each bar and the link reactions.