Problem 2.2-14 The frame construction of a factory workshop is built from two angled girders that are hinge supported in A and B and connected by the hinge H. The dead-load of the roof and an additional snow load are represented by the distributed load q = 8 kN/m. Moreover, a horizontal wind-load is simplified by a single concentrated force F = 10 kN, acting at the upper left corner of the frame. F 4 m A 5 m H 5 m B

Problem 2.2-14 The frame construction of a factory workshop is built from two angled girders that are hinge supported in A and B and connected by the hinge H. The dead-load of the roof and an additional snow load are represented by the distributed load q = 8 kN/m. Moreover, a horizontal wind-load is simplified by a single concentrated force F = 10 kN, acting at the upper left corner of the frame. F 4 m A 5 m H 5 m B

Name: Problem 2.2-14The frame construction of a factoryworkshop is built fr
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Problem 2.2-14The frame construction of a factoryworkshop is built from two angled girdersthat are hinge supported in A and B andconnected by the hinge H. The dead-loadof the roof and an additional snow loadare represented by the distributed loadq =

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.4.10P: A long re Lai nine: wall is braced by wood shores set at an angle of 30° and supported by concrete...

See similar textbooks

Similar questions

A long re Lai nine: wall is braced by wood shores set at an angle of 30° and supported by concrete thrust blocks, as shown in the first part of the figure. The shores are evenly spaced at 3 m apart. For analysis purposes, the wall and shores are idealized as shown in the second part of the figure. Note that the base of the wall and both ends of the shores are assumed to be pinned. The pressure of the soil against the wall is assumed to be triangularly distributed, and the resultant force acting on a 3-meter length of the walls is F = 190 kN. If each shore has a 150 mm X 150 mm square cross section, what is the compressive stress
The horizontal beam ABC shown in thefigure is supported by columns BD and CE. Thebeam is prevented from moving horizontally bythe pin support at end A. Each column is pinned atits upper end to the beam, but at the lower ends, supportD is a sliding support and support E is pinned.Both columns are solid steel bars (E = 30 x 106 psi)of square cross section with width equal to 0.625 in.A load Q acts at distance a from column BD.(a) If the distance a = 12 in., what is the criticalvalue Qcr of the load?(b) If the distance a can be varied between 0 and40 in., what is the maximum possible value ofQcr? What is the corresponding value of thedistance a?
Figure 1 shows a truss under three vertical loads applied at point Question 1' B, C, and D. Find the axial forces in bar AF, CF, and BC. 80 AN 100 KN Fig. 1. The kft of the trus is supported by a pim, aand the right of the truss is supported by a roller.
A new art exhibit featuring mobile works is going up in the Norwalk, CA area. One art work is shown in the figure below. A 105 N uniform beam is pinned to the ground by a pivot. The beam is supported by a cable (attached 3/5 from the bottom of the beam) to allow for each of the shoes to hang freely. Each individual shoe has a weight of 7.5 N. 10 WALL FLOR (a) ( If one shoe is attached 1/7 of the way up the beam and another shoe is attached 5/8 of the way up the beam, with e, = 70.1° and e, 30.1°, what is the tension in the cable, in newtons? %3! %3D (b) What is the x-component of the force, in newtons, that the pivot exerts on the bottom of the beam? (c) O What is the y-component of the force, in newtons, that the pivot exerts on the bottom of the beam?
The truss below is subject to the loads as shown. All of the members are attached at plates and can be treated as pin connected. The truss is attached to the ground with a pin joint at A and a roller at E The applied load H is 335 lb. The applied load J is 211 lb. What is the internal resultant normal force in member CD in lb? (tension is positive, compression is negative) J H B A 1.5ft 3ft D E 3ft 3ft
The truss below is subject to the loads as shown. All of the members are attached at plates and can be treated as p connected. The truss is attached to the ground with a pin joint at A and a roller at C. The applied load H is 531 N. The applied load J is 128 N. What is the internal resultant normal force in member EF in N? (tension is positive, compression is negative) J A 4 m E B 4 m C F 4 m H GA D 6 m
A new art exhibit featuring mobile works is going up in the Holland, MI, area. One piece is shown in the figure. The 155-N uniform beam is pinned to the ground by a pivot. The beam is supported by a cable (attached to the center of the beam) to allow for each of the shoes to hang freely. Each individual shoe has a weight of 9.5-N. If one shoe is attached two-fifths of the way up the beam and another shoe is attached and three-fifths of the way up the beam, with θc = 16.5° and θb = 33.6° as shown in the figure, what is the tension in the cable, in newtons? What is the x-component of the force, in newtons, that the pivot exerts on the bottom of the beam? Use the coordinate system specified in the figure. What is the y-component of the force, in newtons, that the hinge exerts on the bottom of the beam? Use the coordinate system specified in the figure.
1. Find the load in members AD and AE for the truss shown in the figure. Use last three digits of your ID for the load P 87 KN 1.5 m 2 m C 2 m 120 KN 3m E 4.5 m 2 m PKN among
The truss below is subject to the loads as shown. All of the members are attached at plates and can be treated as pin connected. The truss is attached to the ground at a pin joint at G and a roller at D. The applied load H is 357 N. The applied load J is 321 N. What is the internal resultant normal force in member AE in N? (tension is positive, compression is negative) E F G A 3 m B Η. 3 m 3 m D 5 m
Problem 3 The boom AB supports a load of W = 720 lb. The boom is supported by a ball-and-socket joint at A and by two cables, BC and BD. Find the tension in each cable and the axial force in the boom, assuming that point C is 4 inches vertically above the position shown in the figure and the other dimensions are unchanged. Neglect the weight of the boom. -9 in.- 8 in. B 12 in. W = 720 lb %3D
95lall H+ Quiz 3.pdf The jih crane is pin connected at ( A) and supported by a smooth collar at ( B ). determine the reactions on the jib crane at the pin ( A ) and smooth collar (B ).The load is ( 25 kN ) as shown in the figure. 2.5m 25 kN 2 m açraa db 1:20p äc lul 21.03.03
The rigid bars shown are separated by a roller at Cand pinned at A and D. A steel rod at B helps support the load of P 55 kN. Compute the vertical displacement of the roller at C. Given: a - 2 m, b 3 m, C= 3 m, d 1.9 m. E - 203 GPa, A 337 mm and L-2 m. Answer must be in mm.