Prer m. hydrant nozzle in Fig. 1 has inlet and outlet diameters, D₁ = 8 cm and D₂ = 1.0 cm. Water at 20°C flows through the nozzle at 0.001 m³/s and exits to the atmosphere. The atmospheric pressure is 101.3 KPa. Neglect the weight of the piping and nozzle. Compute: a) The exit fluid velocity, V2, ( b) The inlet pressure, Pl c) The horizontal force which must be resisted by the flange bolts d) The moment acting on the flange neglect the weight of the hydrant and water

Prer m. hydrant nozzle in Fig. 1 has inlet and outlet diameters, D₁ = 8 cm and D₂ = 1.0 cm. Water at 20°C flows through the nozzle at 0.001 m³/s and exits to the atmosphere. The atmospheric pressure is 101.3 KPa. Neglect the weight of the piping and nozzle. Compute: a) The exit fluid velocity, V2, ( b) The inlet pressure, Pl c) The horizontal force which must be resisted by the flange bolts d) The moment acting on the flange neglect the weight of the hydrant and water

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A soft drink (mostly water) flows in a pipe at Asia Brewery with a mass flow rate that would fill 220 0.355-L cans per minute. At point 2 in the pipe, the gauge pressure is 152kPa and the cross-sectional area is 8.20cm2. At point 1, 1.35 m above point 2, the cross-sectional area is 2.20 cm2. Find the gauge pressure at point 1.
A/ A tank fill by the liquid and partially immersed a very long vertical tube in it. The tube has the radius R and rotating at o radians per second clockwise. Find the steady state velocity and pressure profiles in cylındrical coordinates.
! MIN 1/1 米 4:22 PM O O 81% Find a relation between nozzle discharge velocity V2 and tank free surface height h as in figure below. Assume steady frictionless flow. HGL - II Open jet:
3. In the figure, ideal fluid (water) flow from the infinity large basin through the atmosphere. Diameters of the pipes for AB, is 0.30 m, BC is 0.10 m and, CD is 0.20. The absolute atmospheric pressure is 1kgf/cm² and the absolute vapor pressure is 0.025 kgf/cm?. According to given data; 0.40m 0,10m 0.30m 0.20m Determine the discharge of the system a. and calculate velocities in each part of the system, Determine the possible maximum axial height of the BC pipe (z) and draw the absolute and relative (hydraulic) grade b. 0,00m lines for this condition.
A 2-1/2 inch fire hose discharges water through a nozzle having a jet diameter of 1 inch. Thelost head in the nozzle is 5.76 percent of the velocity head in the jet. If the gage pressure atbase of nozzle is (a) 86 lb per sq in.: (b) 167 lb per sq in.: (1.1) compute the discharge ingallons per minute: (1.2) what is the maximum horizontal range to which the stream can bethrown, neglecting air resistance?
An incompressible fluid (density 1000kg/m3) is flowing through a pipe with a constriction. The pipe is on an angle of 30 degrees with the narrow section at at distance of 10m from the wide section and lower that the wide section . The speed of the fluid in the wide section is 2m/s and 10m/s in the narrow section, I f the pressure in the wide section in 250 kPa. What is the pressure of the fluid in the narrow section ?
The sprinkler system is used for watering the garden as given figure below. Working fluid enters the system at 7,75 liters/s. Calculate the required torque [N.m] holding the system as stationary for e=30°. (NOTE: Take p=1000 kg/m³) 0.5m Nozzle exit area normal to, relative velocity = 18 mm?
Find the Base Temp at Airflow=0.1 m/s. it's an exponential relation. will upvote if correct.
Q3/ Water is flowing upwards in an inclined homogeneous pipe from point No. (1) to point No. (2). The following data is available:- 1- Length of pipe, L= 1400 (m). 2- Diameter of pipe, d= 0.25 (m). 3- Elevation of point No. (1) is 15 (m) above the Reference line and elevation of point No. (2) is 30 (m) above the Reference line. 4- Piezometric head at point No. (1), hi= 61.16 ( m of water height). 5- Piezometric head at point No. (2), h2= 20.39 (m of water height). 6- Friction coefficient f=0.02 and hL=zero Find: 1- Head loss of water flow in the pipe from point No.(1) to point No.(2) due to friction hf. 2- Water flow rate Q and flow velocity v in the pipe. Draw the H.G.L. of water flow in the pipe from point No. (1) to point No. (2).
Consider the following figure showing a jet of water supporting a weight of 100 N at aheight of 5 m . Water leaves the nozzle with a velocity of 20 m/s. The diameter d ofthe nozzle will be
A bicycle tire is fi lled with air at an absolute pressure of169.12 kPa, and the temperature inside is 30.0 °C. Supposethe valve breaks, and the air starts to exhaust out of the tireinto the atmosphere (pa = 100 kPa absolute and Ta =20.0 °C). The valve exit is 2.00 mm in diameter and is thesmallest cross-sectional area of the entire system. Frictionallosses can be ignored here; one-dimensional isentropicflow is a reasonable assumption. (a) Find the Machnumber, velocity, and temperature at the exit plane of thevalve (initially). (b) Find the initial mass flow rate out ofthe tire. (c) Estimate the velocity at the exit plane using theincompressible Bernoulli equation. How well does thisestimate agree with the “exact” answer of part (a)? Explain.
Consider a following figure showing a jet of water supporting a weight of 100 N at a heigh of 5m. Water leaves the nozzle with a velocity of 20m/s .The diameter d of the nozzle will be?