Please solve ASAP The magnetic relay in the figure has a coil of 500 turns currying acurrent I = 4,19 A. The mean core path length is l. = 360 mm and theair gap is = 1,5 mm. The relative permeability of the core isCoreMean pathH. =1250 and its cross-section is A. =100 mm?. Neglect flux fringingin the air gaps.a) Draw the equivalent magnetic circuit of the relay and calculate itsparameters, (MMF and reluctances)'b) Calculate the flux density in the air gap (use the circuit in (a))c) Calculate the total force acting on the moving partSimplified magneticrelay.

Answered: Image /qna-images/answer/3f98545d-d009-467f-a661-0876d91367a1.jpg

Answered: Please solve ASAP

Engineering

Electrical Engineering

Please solve ASAP

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

(a) Explain briefly what is fringing effect and leakage flux. (b) A ferromagnetic core is shown in Figure 1. The depth of the core is 10 cm. The other dimensions of the core are as shown in the figure. By assuming the magnetic leakage to be negligible and relative permeability of the core is 800. Calculate the total reluctance and find the value of the current that will produce a flux of 0.01 Wb. With this current, calculate the flux density at the top of the core 20 cm 40 cm 10 cm, 30 cm 500 turns 30 cm 30 cm Figure 1
-4 poles-26 conductors-double layer-simplex wave winding Can you do this in "armature winding"? Thank you.
5 The core of an electro-magnetic structure is Laminated in order to: reduce the Stacking Factor reduced the Hysteresis Loss of the core reduce the Eddy-Current Loss of the core improve the Input Power Factor of the structure.
3 For a coil, each turn faces (2t4 – t³ – 2t) milliwebers of flux. The value of induced EMF in coil for 100 turns coil at 2 sec is, (in Volts).
Consider the magnetic circuit shown in Figure T14.4. The core has a relative permeability of 1500. a. Carefully estimate the flux density in the air gap. b. Determine the inductance of the coil.
The .. of the hysteresis loop is a measure of energy ..... lost per cycle a) area. b) Type. c) Frequency d) No one of the above. Fringing effect is a phenomena occurs in . a) Transformers. b) Electrical field. c) Air gap d) All of the above.
4. The portion of the flux that goes through one of the transformer coils but not the other one is called. A) Average flux B) Mutual flux D) Leakage flux C) Total flux 5. The fundamental component of the magnetization current ------- the voltage applied to the core by ------ 90°: A) Lags, 45° B) Leads, 45°. D). Leads, 90°. C) Lags, 90°. 6. The ----- are resistive heating losses in the core of the transformer. A) Hysteresis losses. B) Copper losses. C) Leakage flux losses. D) Eddy current losses. 7. The total rotational losses of an induction motor are a combination of: A) Friction losses B) Windage losses. C) Core losses. D) Stray losses. 8. Induction motors are now the preferred A) absence of brushes. choice for industrial motors due to B) Small size. C) Less control requirements. D) rugged construction. 9. For an induction motor, if the synchronous speed is 1800 r/m, and the rotor speed 180rad/sec, then the slip will be: A) 5.5 % C) 6% B) 4.5% D) 4% 10. The lower the speed of an…
The physical construction of two pairs of magnetically coupled coils is shown. Assume that the magnetic flux is confined to the core material in each structure. Show two possible locations for the dot markings on each pair of coils.
Which of the ff given below is the eddy current loss not proportional to? Square of the frequency Square of the flux density Square of the load current of the laminated core Square of the thickness
Compute the flux in each leg of the core shown in Figure P14.33. Account for fringing by adding the gap length to each of the cross-sectional dimensions of the gap.
Explain why, when steel is subjected to alternating magnetization energy, losses occur due to bothhysteresis and eddy currents. The core loss in a transformer core at normal flux density was measured atfrequencies of 40 Hz and 50 Hz, the results being 40 W and 52.5 W respectively. Calculate, at a frequencyof 50 Hz, (a) the hysteresis loss and (b) the eddy current loss. Clear and detailed solution.
vii. When two magnetic circuits are coupled..... the coupling coefficient is expressed by (a) K=M\ VL1 L2 viii. Impedance matching means (a) Transfer power to the load (c) Maximum power transfer to the load. (b) k= MIM2 (c) K= LIL2 (b) Minimum power transfer to the load