PLATE NO 3 Method of Sections Chapter 5 Problem 5-2 Page 76 Using the method of sections, determine the kind and amount of stress in the following members of the truss shown in figure P5-2 (page 76). U:U2 UIL2 LIL2 U2U3 U2L3 L2L3 1000lb 1000lb Usy 1000lb 1000lb 1000lb Uz U4 h=20ft 500lb U Us 500lb Lo L1 L2 L3 L4 Ls RAV 6 panels at 10' = 60 ft RBV

PLATE NO 3 Method of Sections Chapter 5 Problem 5-2 Page 76 Using the method of sections, determine the kind and amount of stress in the following members of the truss shown in figure P5-2 (page 76). U:U2 UIL2 LIL2 U2U3 U2L3 L2L3 1000lb 1000lb Usy 1000lb 1000lb 1000lb Uz U4 h=20ft 500lb U Us 500lb Lo L1 L2 L3 L4 Ls RAV 6 panels at 10' = 60 ft RBV

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 2 Given is a truss structure: Where: • Working shear stress for the rivets is 70 MPa • Working bearing stress due to rivets is 140 Mpa • Thickness of the member is 5 mm • Thickness of the Gusset plate is 6 mm Rivet diameter is 15 mm Determine the no. of rivets to fasten the member BD 80 N 120 N 200 N 4 Pands 4m - 16 m
Given is a truss structure: Where: Working shear stress for the rivets is 70 MPa Working bearing stress due to rivets is 140 Mpa Thickness of the member is 5 mm Thickness of the Gusset plate is 6 mm Rivet diameter is 15 mm Determine the no. of rivets to fasten the member BD 80 kN 120 kN B. 3 m E 200 kN 4 Panels @ 4 m = 16 m
In the steel structure shown a 6 mm diameter pin is used at C and 10 mm diameter pin is used at B. The ultimate shearing stress is 150 MPa at all the connections. What is the largest P that can be applied? Front view 160 mm 18 D -18 Top view 120mm C D 6 mm 8 Side view
I need a clear answer by hand, not by keyboard and fast answer within 20 minutes. Thank you | dybala For the beam loaded as shown, find the maximum tensile and compressive bending stresses and maximum shearing stress.. IN.A=4*10mm* 80mm 100mm 60mm 60mm 1.5KN 2kN/m 1mal A |-----|- | Im ++ Im->> 3m 3kN/m
The homogenous material wire ABCD is bent as shown and is attached to a hinge at C. Determine the length L in mm in which portion BCD of the wire is horizontal in position. Determine the length L in mm in which portion AB of the wire is horizontal in position (meaning portion BCD is inclined) -80 mm- B IC 60 mm
4.) A thin plate PQR is deformed so that the corner Q is displaced downward 1.0 mm to new position Q' as shown. Determine the shear strain at Q' associated with the two edges. 5) A pin mado of steo1 ie insorted in o short hanging TAOodon mombor ond iG 1used to Supnort lond E - 20
B 6m LP P -8m- -8m- -8m -8m In the bridge truss shown in figure, the end chord AB is composed of two C 230 x 30 channels latticed together so that the fabricated section has equal moments of inertia about the axes of symmetry. Properties of C 230 x 30 Ix = 25.5 x 10^6 mm^4 A=3800 mm^2 %3D a. Determine the slenderness ration of section AB. b. Determine the capacity of member AB. c. If the safe load P on the truss is governed by the strength of member AB, which of the following gives the value of P using NSCP Specifications with Fy = 290 MPa. %3D
How many Zero force members are there in the truss shown? B, F А HL100 1 60 VkN VkN K L1 60
Trusses 1. Find the stresses of FAB. FAC., FBC & FBD- 20 k 15 k D 60° 60 60° 5' 10 10 Ra Rb
EQuiz No.3 584nkkz1 Cc7KLzOsdr9YUFgvcfFSqpsdlyljtewQ/formResponse Choose the correct answer What will be the value of load applied parallel to the diagonal of (100x100x100))mm cube since the splitting tensile strength=3 Mpa 57.8 KN O 46.7 KN O 47.1 KN O (28)=27.5 Mpa, then the fc(180)=-- for concrete produced using moist
Determine the force in each member of the truss shown by method of joints. Note: Indicate whether the force is in compression (C) or tension (T) 27KN 54KN 70KN 90KN 36KN В Gv 6m A- D E RA 4@ 4.5m = 18m %3D
In the bridge truss shown, the end chord AB is composed of two C 230 x 30 channels latticed together so that the fabricated section has equal moments inertia about the axes of symmetry. Fy=290 MPa Properties of one C 230 x 30 Ix=25.5x105 mm² A = 3800 mm² B VP P CHIL ENGINEERING-STEEL DESIGN