Part A If the maximum average normal stress for the washer is max = 60 ksi and the maximum average shear stress is Tmax= 19 ksi, determine the force F that must be applied to the bushing that will cause this to happen. The washer is in thick. Express your answer to three significant figures and include the appropriate units. 16 F = Submit μA Value Request Answer C Units EMAC ?

Part A If the maximum average normal stress for the washer is max = 60 ksi and the maximum average shear stress is Tmax= 19 ksi, determine the force F that must be applied to the bushing that will cause this to happen. The washer is in thick. Express your answer to three significant figures and include the appropriate units. 16 F = Submit μA Value Request Answer C Units EMAC ?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

ull 4G 10:26 Enter your answer 10 If the weight of the block shown is 90kN and to be located at the center of gravity G. What is the tensin in cables DE, AC and BC for equilibrium? TDE = TAC = ..... TBC = .... B 3 m 4m 6 m 4m 3m
A two pinned end bars AB (Copper), ? = 850 ??2, ? = 120 ??? and BC (Aluminum), ? = 1000??2, ? = 70 ??? is subjected to a horizontal force of 100 ?? applied at pin B as shown in the figure, determine the horizontal displacement of pin B.
Two aluminum (Ea=77 GPa) rods AB and CD, and a steel (Es=202 GPa) rod EF support a 82.7 kN load P. Each of the rods has a 400 mm2 cross- sectional area. Neglecting the deformation of rod BED, determine the change in length (in mm correctly up to two decimal places) of rod AB. A C P 500 mm В E 400 mm F
The pipe assembly is subjected to a force of 600 N at B. 150 mm 150 mm Part A 400 mm B 60° 30° 600 N 500 mm Tap image to zoom Determine the magnitude of the resultant internal normal force acting on the cross section at C. Express your answer to three significant
Q19: In Figure below, what is the ratio of P to F h Waer Hinge Sec A-A
Q.1: A shaft composed of segments AB, BC is fixed between the two walls at A and C and loaded as shown in Figure below. For steel has a 25 mm circular cross section, shearing modulus G = 83 GPa. For aluminum has a 30 mm circular eross section, shearing modulus G 28 GPa Determine: The two torques at supports A and C 2N.m B 3m 4m Steel aluminum Di-25mm Di-30mm G-83GPa G-28GPa
d. Calculate "P" in KN considering failure on shear on rivets Two A36 16mm Thick Steel Plates Are Connected By Four Rivets With Fv=152 MPa As Shown. Given: Rivet Dia 20 mm x=100 mm
4 - Two circular shafts are connected via a gear assembly as shown in the figure. Shaft 1 is fixed to a wall at point A. Torque T is applied to shaft 2 at point D. Shaft 1 is made of steel with a shear modulus of 85 GPa; shaft 2 is made of aluminum with a shear modulus of 28 GPa. The other relevant paramters are indicated alongside the figure. The shafts are restrained by bearings such that they do not undergo bending (i.e., it is a case of pure torsion). Determine the angular rotation at point D relative to that at point A. Shafts L₁=1.5m; L₂=1m r=50mm; ₂= 25mm gear radii R₁-200mm ; R₂=40mm Torque T=4KN-m Li B C (2) L2 * assume the gears to be rigid ↑
4 - Two circular shafts are connected via a gear assembly as shown in the figure. Shaft 1 is fixed to a wall at point A. Torque T is applied to shaft 2 at point D. Shaft 1 is made of steel with a shear modulus of 85 GPa; shaft 2 is made of aluminum with a shear modulus of 28 GPa. The other relevant paramters are indicated alongside the figure. The shafts are restrained by bearings such that they do not undergo bending (i.e., it is a case of pure torsion). Determine the angular rotation at point D relative to that at point A. Shafts L₁=1.5m; L₂=1m r=50mm; ₂= 25 mm gear radii R₁-200mm; R₂=40mm Torque T=4KN-m Li C L2 * assume the gears to be rigid T
A rigid bar ABCD is supported by two bars as shown in the figure. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in rod (1) is -1350 µm/m. Determine the normal strain in rod (2) if there is a 1-mm gap in the connection at pin C before the load is applied. A 240 mm B (1) O 1281 um/m O 1877 µm/m O 1141 µm/m O 1358 µm/m O 999 µm/m 360 mm (2) Rigid bar 900 mm C 140 mm, 1,500 mm
An aluminum bar having a cross-sectional area of 160 mm2 carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B1= 0.8 m; B2 = 1.0 m; B3= 0.6 m. Determine the axial load acting on bar B3 in kN. 35KN В1 B2 ВЗ ... 10KN 15KN 30KN A 35 20 10 D 5
"The force applied at the handle of the rigid lever causes the lever to rotate clockwise about the pin B through an angle of 2°. Determine the average normal strain in each wire. The wires are unstretched when the lever is in the horizontal position. (i of. 200 mm 200 mm 300 mm 300 mm E B D 200 mm H Figure 3. Problem 3.