P P P P P 6 T 6 66 6 6 i (a) Determine the deflection & at the midpoint of the beam. (Enter the magnitude. Use the following as necessary: P, L, E, and I.) 8₁ = (b) If the same total load (5P) is distributed as a uniform load on the beam, what is the deflection 82 at the midpoint? (Enter the magnitude. Use the following as necessary: P, L, E, and I.) 8₂ = (c) Calculate the ratio of ₁ to ₂. B

P P P P P 6 T 6 66 6 6 i (a) Determine the deflection & at the midpoint of the beam. (Enter the magnitude. Use the following as necessary: P, L, E, and I.) 8₁ = (b) If the same total load (5P) is distributed as a uniform load on the beam, what is the deflection 82 at the midpoint? (Enter the magnitude. Use the following as necessary: P, L, E, and I.) 8₂ = (c) Calculate the ratio of ₁ to ₂. B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at B and (b) the deflection of the beam at. A. Assume a constant value of EI = 113000 kip-ft² for the beam; wo = 2.0 kips/ft, LAB = 15 ft. LBC= 8 ft. - Wo A Answer: (a) 8B = (b) VA= LAB rad in. B LBC C X
The beam with, cross-section shown, is subjected to the load shown. Using E=200 GPa, determine a. the value of Ely at B and D b. the deflection at B and D 4 Kum 16AN 25 mm 140 mm 6m 4m 2m 25 mm 120 mm
The bending stiffness of the beam given the loading condition in the figure is El. Determine according to this with donmy Mohr method at point A
Analyze the beam shown in Figure using flexibility method of analysis. Take EI as constant.
3) For the beam and loading shown in ﬁgure, E = 30 × 106 psi, I¯ = 200 in4. Determine (a) the reaction force at A and(b) the deﬂection at C.
Q1: Solve Determine a scalar d so that the angle between A=2i+4j and B = 9itdj is 45°.
Determine the horizontal and vertical deflections at D for the frame shown below (consider E, I constant and neglect axial deformation). P |2L A В C 4L
EI=constant . Find maximum deflection
For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at B and (b) the deflection of the bearn at C. Assume a constant value of EI = 34 x 106 lb-ft² for the bear; wo = 6400 lb/ft, LAB= 4.0 ft. LBC = 9ft,Lco=5 ft. LAB Answer: (a) 8B = (b) vc= Wo B LBC rad in. LCD D X
QUESTION 03 A beam ABCD is supported and loaded as shown in Figure Q3. The flexural rigidity, El is constant. By using Macaulay's method, and take point A as origin, determine the: (a) Reactions at all supports A, C and D. (b) Deflection at point B (c) Slope at support A 1 m 1 m 1 m 2 kN/m 4 kNm Figure Q3/ Rajah S3
For the beam shown, EI = Constant. Determine the following: A. Slope at B B. Deflection at C C. Location of the maximum deflection D. maximum deflection
A truss is subjected to loads as shown. Assume AE is constant and use virtual work method for deflection of truss. 4m 120 KN B A TINT 3m EA = constant E = 200 G Pa 2 A = 1,500 mm Find the vertical deflection at B in mm