What’s the correct answer for this please? Consider water is flowing through a pipe with a10 cm diameter at a flow rate of 0.2 kg/s. Theinlet mean temperature of the water is 25 °C. Ifthe wall of the pipe is heated with an electricresister generating heat at a rate of 5 kW andmaintaining a uniform wall heat flux, determinethe outlet mean temperature of the water.The properties of water at this temperature aregiven as; specific heat capacity C, = 4.18 kJ/kg-K, thermal conductivity k = 0.607 W/m-K,Density p = 997 kg/m³, and kinematic viscosityv = 8.9 x 10-7 m²/s.19 °C23 °C27 °C31 °C

Given: Heat generated=5 kW m=0.2 kg/s Cp=4.18 kJ/kgK Ti=25oC To determine: Outside temperature

Answered: outlet mean temperature of the water.

Engineering

Mechanical Engineering

outlet mean temperature of the water.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A gardener is thinking of installing piping system for watering the plants in his garden located near a water reservoir. The reservoir is located at an elevation of 150 m above from the surface, as shown in figure. The diameter of pipe (cast iron) is constant equal to 15 cm and total length of pipe is 180 m. It is desirable that the exit velocity of water to the garden should not exceed 5 m/sec and water is at atmospheric pressure and temperature is 20°C. The gardener is planning to open the valve for 3 hours daily. Calculate the followings: a) How much volume of liquid can be drawn from reservoir in a day? b) How much total irreversible head loss will be occurred in the system?
Consider water is flowing through a pipe with a 10 cm diameter at a flow rate of 0.2 kg/s. The inlet mean temperature of the water is 25 °C. If the wall of the pipe is heated with an electric resister generating heat at a rate of 5 kW and maintaining a uniform wall heat flux, determine the average convective heat transfer coefficient between water and wall of the pipe. The properties of water at this temperature are given as; specific heat capacity Cp = 4.18 kJ/kg-K, thermal conductivity k = 0.607 W/m- K, Density p = 997 kg/m³, and kinematic viscosity v = 8.9 x 10- 7 m²/s.
Oil at 20°C is flowing through a vertical glass funnel that consists of a 20-cm-high cylindrical reservoir and a 1-cm-diameter, 40-cm-high pipe. The funnel is always maintained full by the addition of oil from a tank. Assuming theentrance effects to be negligible, determine the flow rate of oil through the funnel and calculate the “funnel effectiveness,”which is defined as the ratio of the actual flow rate through the funnel to the maximum flow rate for the “frictionless” case. Answers: 3.83 × 10−6 m3/s, 1.4 percent. Can you provide a solution for this?
Glycerin at 40° C with p = 1252 kg/m³ and u = 0.27 kg/m.s is flowing through a 8-cm diameter horizontal pipe with 3.0 m/s flow velocity. Determine the pumping power required to maintain the flow for a 10 m long pipe.
The air duct of the heating system of a hall, an electric heater placed inside andIt consists of a 300 W fan. While the air is continuously flowing in the duct with a flow rate of 0.6 kg/stemperature rises by 5°C. Since there is a loss of 400 W 151 from the channel surfaces to the environmentCalculate the power of the electric heater. (The specific heating value of air is - 1.005 kJ/kgK.)
Steam flowing at a rate of 10 kg/h enters a steam turbine at a velocity of 50 m/s andleaves at a point 5 m below the inlet at a velocity of 300 m/s. The heat loss from the turbine is estimated to be 10 kW, and the turbine delivers shaft work at a rate of 70 kW. Calculate the change in enthalpy transport rate of the process
In many manufacturing plants, individuals areoften working around high-temperature surfaces.Exposed hot surfaces that can cause thermal burns on humanskin are considered hazards in the workplace. Metallic surfacesabove 70° C can instantly damage skin that touches them.Consider an AISI 1010 carbon steel strip (? = 7832 kg/ m 3 )2 mm thick and 3 cm wide that is conveyed into a chamber tobe cooled at a constant speed of 1 m/s. The steel strip entersthe cooling chamber at 597° C. Determine the rate at whichheat needs to be removed so that the steel strip exits the chamberat 47° C . Discuss how the conveyance speed can affect therequired rate of heat removal.
Seawater is to be pumped into a large tank at a rate of 165 kg/min. The tank is opwn to atmostsphere and the water enters the tank from a 80 m height. The overall efficiency of the motor pump unit is 75 percent and the motor consumes electricity at a rate of 3.2 KW. If the irreversible headloss in the piping is 7 m, the velocity of the water (in m/s) at the tank inlet is A.8.7 B.7.12 C.6.21 D.5.05
Seawater is to be pumped into a large tank at a rate of 165 kg/min. The tank is opwn to atmostsphere and the water enters the tank from a 80 m height. The overall efficiency of the motor pump unit is 75 percent and the motor consumes electricity at a rate of 3.2 KW. If the irreversible headloss in the piping is 7 m, the velocity of the water (in m/s) at the tank inlet is include your freebody diagram A.5.05 B.8.7 C.6.21 D.7.12
Seawater is to be pumped into a large tank at a rate of 165 kg/min. The tank is opwn to atmostsphere and the water enters the tank from a 80 m height. The overall efficiency of the motor pump unit is 75 percent and the motor consumes electricity at a rate of 3.2 KW. If the irreversible headloss in the piping is 7 m, the velocity of the water (in m/s) at the tank inlet is ( WITH FREE BODY DIAGRAM) CHOICES: A.7.12 B.6.21 C.8.7 D.5.05
Seawater is to be pumped into a large tank at a rate of 165 kg/min. The tank is opwn to atmostsphere and the water enters the tank from a 80 m height. The overall efficiency of the motor pump unit is 75 percent and the motor consumes electricity at a rate of 3.2 KW. If the irreversible headloss in the piping is 7 m, the velocity of the water (in m/s) at the tank inlet is. Ans: 6.21Note: Include free body diagram
Seawater is to be pumped into a large tank at a rate of 165 kg/min. The tank is opwn to atmostsphere and the water enters the tank from a 80 m height. The overall efficiency of the motor pump unit is 75 percent and the motor consumes electricity at a rate of 3.2 KW. If the irreversible headloss in the piping is 7 m, the velocity of the water (in m/s) at the tank inlet is A. 5.05 B. 8.7 C. 7.12 D.6.21 With F.B.D