On bar BD, what is the x component ofА.the force at B?(include units with answer)On bar BD, what is the y component ofthe force at B?(include units with answer)B. hBh+ d + ddTHE FIGURE IS NOT DRAWN TO SCALE. Also, A and E are BOTH pinned (hinged) supports (even though they're not drawn that way). Numerical values for the parametersshown are P = 680 N, d = 0.40 m and h = 0.40 m. For component directions, use x positive to the right and y positive upward.

Answered: Image /qna-images/answer/06d20118-c085-4852-8e94-af95963929e1.jpg

Answered: On bar BD, what is the x component of…

On bar BD, what is the x component of the force at B? A. (include units with answer) On bar BD, what is the y component of В. the force at B? (include units with answer)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A A squere plate is boended by the liner x = ±2, y= ± 2. The boundlary femperatures %3D are on the hine y=2, T=-8o on the line x-12,T=-40Y on the line y=-2, T= 240 + 8ox for -25x Ko 7 = 240 - 8o x tor o
Draft and annotate the 2D sketch of support using AutoCAD and mention all the dimensions. Colour the hatched lines (blue) which are inside the curve. 32 R 24 R 3 holes 26 Dia 45R 18 R. 124 Diá 18 R 20 R 22R 76 Support 110 28R
Problem 4: Values: a = 300 mm b = 75 mm c = 100 mm Use the graphical method to break F into components parallel to bars AB and BC. If the component parallel to bar AB is 7 kN, what is the magnitude of F? Comments: B This is a perfect example of why the graphical method is useful - we are asked to resolve a force into components that are not perpendicular to one another. It's difficult to apply regular old sine and cosine (i.e. trig) for this because we're not dealing with right triangles. Instead we will use the law of sines and/or the law of cosines. • Start by drawing a vertical line to represent the vector F. Now draw a line parallel to AB passing through the top of F, and another line, also parallel to AB, through the bottom. Repeat for BC. You should have a parallelogram divided into two triangles by the resultant vector F. Pick one of the triangles to work with, use geometry to figure out the angles, and then apply the law of sines to compute the magnitude of F. Remember, these…
A pole extends from the origin to point A. A wire connects points A and B. Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value a 4.5 m 2 m 2.5 m 1.5 m a. Determine the position vector from point A to origin (r AO), express as a cartesian vector. b. Determine the position vector from point A to B (7AB), express as a cartesian vector. Round your final answers to 3 significant figures. k) m AO k) m TAB
Q1:- if the La = [1 3 5] and B =[1:4:6)].... Find the force scaler and force vector?
Determine the DE for: Straight lines at a fixed distance P from the origin. a. (xy" – y)? = P²[1+ (y')²] %3D b. (xy' – y)? = p2[1+ (y')²] c. (xy' – y)3 = p3[1+ (y')³] d. (xy" – y)3 = p³[1 + (y')³] e. none of these
3. Find VR and Vc AO2=30mm В AB=60mm AC=80mm BC=45mm A B04=50mm 0,= 2 rad/s 0204=70mm 04 O4 Angle of 02A is 45 degrees with respect to positive x-axis.Drawing is not in scale redraw if possible and applicable.
Line AB 100 mm long is 30° and 45° inclined to HP & VP respectively. End A is 10 mm above HP and it's VT is 20 mm below HP. Draw projections of the line and it’s HT.
Please find the Grashof classification and the Barker classification of the two four-bars: (NOTE: distances are in non-dimensional units. Can use inches or cm) P1) L1=d=4, theta1=0 degrees, L2=a=1.6, theta2=60 degrees, L3=b=5.5, L4=c=4.5 P1) L1=d=1, theta1=0 degrees, L2=a=1.25, theta2=120 degrees, L3=b=1.5, L4=c=2 Please also draw the four-bars to estimate the unknown angles theta3 and theta4.
te F B (0,0,0) <3 of 3 An old wooden telephone pole with a single cross member was blown off center during a recent storm To temporarily stabilize the telephone pole, a repair crew has attached a cable from the end of the cross member to an eye-ring stake anchored in the ground. (Eigure 3) If the origin O of a coordinate system is placed where the pole meets the ground, the point where the cross member is attached to the pole is A(-1.50, 2.10, 23.9) ft and the point where the cable is attached to the end of the cross member is B(-1.50,-2.90, 26.9) ft. The cable's direction is (1.00-1.00-1.00k) and it has a tension of 145 lb. What is M₁, the moment that tends to twist the telephone pole due to the tension in the cable applied at point B? Express your answer numerically in pound-feet to three significant figures. ▸ View Available Hint(s) M₁ = V ΑΣΦ it vec ? lb-ft
! Required information A rope connecting points A and B supports the force Fshown in the figure. Write expressions using Cartesian vector representation for the following. Take L = 8 ft and F= 12 Ib. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. y B 30° ÜBA : the unit vector from B to A. ÜBA
Q2/scale the Rhombus defined by the points p1=( 3,1), p2=(5,3), p3=(3,5) & p43(1,3) by a scale factor of 1/2 keeping the first point in the same location