Completely solve and box the final answers. Write legibly.Only solve numbers 4 and 5. Use the beam loaded as shown for the following questions:100 lb80 lbBCRear2f-4ft--3 ft.1. If the beam cross section is a rectangle with a breadth anddepth of 6 in and 8 in respectively, what is the bendingstress?2. If the beam crosssection is a rectangle with a breadth and8 in respectively, what is the sheardepth of 6 in andstress?3. If the beam cross section is circular with diameter of 8in, determine the shear stress.4. Compute for the midspan value of Ely in lb. ft³5. Considering the following design conditions for the beam:Allowable bending stress: 20000 psiAllowable shear stress: 10000 psiMaximum allowable deflection: L/360Determine the safe dimensions depth h and breadth b ininches if h = 2b.

Given Data: Simply supported beam It is asked to solve question number 4 and 5

4. Compute for the midspan value of EIy in lb. ft³ 5. Considering the following design conditions for the beam: Allowable bending stress: 20000 psi Allowable shear stress: 10000 psi Maximum allowable deflection: L/360 Determine the safe dimensions depth h and breadth b in inches if h = 2b.

4. Compute for the midspan value of EIy in lb. ft³ 5. Considering the following design conditions for the beam: Allowable bending stress: 20000 psi Allowable shear stress: 10000 psi Maximum allowable deflection: L/360 Determine the safe dimensions depth h and breadth b in inches if h = 2b.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

en 1 The cross-section of a beam is as shown below, then the section modulus (S) of the section is: ed out of uestion N - A d. b. (Approx 2 Min) O bd³/6 O bd?/6 O bd/12 O bd?/12
M Inbe x Qui: x t T2 x C X O FO x E PLA X PLAX Plat x I PLS x 0x 卡 feu.instructure.com 2. Compute the maximum unsupported length of the simple beam to adequately support the given unfactored loads. Use f'c=21MPa, fy=D415MPA, f,-10mm, and cc350mm. 250 mm Pu Loads: WDL=10KN/m WLL=30KN/m PDL-40KN PLL-60kN Wu A. BO 400 mm 3-28ф KL/2 L/2 Edit View Insert Format Tools Table 12nt Paragranh A. A 4) O ENG 1:59 pm
Shear Flow The Built Up Beam shown is made by connecting two channel shapes and two plates, using 0.75" diameter bolts spaced length wise at 7.5". Determine the force on EACH bolt if the shear force on the beam is 25 kips 16 in. X in. Moment of Inertia C12 x 20.7 Correct Answer
For the beam shown below: a) Calculate the elastic curve equation O Ely Mo A R³L 6 D Mox³L + x + C₂ L- B
Beam description (repeated): A simply supported beam with aT-shaped section is being designed, as shown in the figure below. The beam has overall dimensions of 900 mm wide top flange, 750 mm deep, and a web thickness of 400mm and flange thickness of 150 mm. A total of 7-HD25 longitudinal reinforcing bars are located in the bottom of the beam, 4-HD25 bars at the top, and 8 - HD16 in the flange. The concrete strength is f'c = 30 MPa. The depth to the centre of the bar group at the bottom of the beam is 675mm. Question: If the unfactored shear actions due to dead and live loads are VG = 300 kN and VQ = 80 kN (including self-weight), calculate the nominal shear stress (vn) acting on the section. Give your answer below in MPa.
An 5355 Class 1 laterally restrained universal beam (UB) does not support a high shear load. What is its Design Bending Resistance Med? Give your answer to the nearest whole kNm. Do not include units in the answer box. Flange thickness t,-34.3 mm Plastic section modulus Wply-3,126 cm³ Plastic section modulus Wez-235 cm³
Situation 4: A W12x106 simply supported beam carries a uniformly distributed load. The properties of the section relevant to the problem are as follow: Use A50 steel and Cb - 1.14 d - 328 mm bf-310 mm tf = 25.1 mm tw = 15.5 mm kdes - 40.4 mm ry - 79.0 mm lx = 388 x 10^6 mm^4 ly - 125 x 10^6 mm^4 Sx - 2380 x 10^3 mm^3 Zx=2690 x 10^3 mm^3 J-3800 x 10^3 mm^3 Cw=2870 x 10^9 mm^6 1. Which of the following nearly gives the Design Strength Moment (LRFD) if the span of the beam is 2.5m? 878 KN-m 793 KN-m 836 KN-m 811 KN m
Situation 1: A W8x31 simply supported beam carries a uniformly distributed load. The properties of the section relevant to the problem are as follow: Use A50 steel and Cb - 1.14 d=203 mm bf = 203 mm tf-11.0 mm tw = 7.24 mm kdes - 21.1 mm ry = 51.3 mm Ix = 45.8 x 10^6 mm^4 ly- 15.4 x 10^6 mm^4 Sx-451 x 10^3 mm^3 Zx = 498 x 10^3 mm^3 J-223 x 10^3 mm^3 Cw-142 x 10^9 mm^6 1. Which of the following nearly gives the maximum safe uniform load (Wu) that the beam could carry if the span of the beam is 5m? Neglect weight of the beam. 46 KN/m 41 KN/m 51 KN/m 33 KN/m
Designation Serial size 457x191 ■ Calculate the design tension resistance of the 457 × 191 × 67 UB. Given information from steel section table (assuming S275): Axis y-y cm³ 1296 67 Elastic modulus Wel Axis Z-Z cm³ 153 Mass per metre kg/m 67.1 Depth of section h mm 453.4 Width of section b mm 189.9 Plastic modulus Wpl Axis y-y cm³ 1471 Axis Z-Z cm³ 237 Thickness Thickness Root of web of flange radius tw tf mm r mm mm 8.5 12.7 Buckling parameter U 0.872 Torsional index X 37.9 10.2 Depth between fillets d mm 407.6 Ratios for local buckling Flange Web Cf/tf Cw/tw dm6 0.705 6.34 Warping Torsional constant lw constant IT cm4 37.1 48.0 Area of section cm² 85.5 Second moment of area Axis y-y cm4 29380 Axis Z-Z cm4 kNm 522 1452 Indicative values for S355 steel Mc.y.Rd Nb.z.Rd* for Lcr=3.5m kN 1600 Radius of gyration i Axis y-y cm 18.5 Axis Z-Z cm 4.12; Designation Serial size 67 457x191
Beam description (repeated): A simply supported beam with a T-shaped section is being designed, as shown in the figure below. The beam has overall dimensions of 900 mm wide top flange, 750 mm deep, and a web thickness of 400mm and flange thickness of 150 mm. A total of 7-HD25 longitudinal reinforcing bars are located in the bottom of the beam, 4-HD25 bars at the top, and 8 - HD16 in the flange. The concrete strength is f'c = 30 MPa. The depth to the centre of the bar group at the bottom of the beam is 675mm. Question: Assuming nominal shear reinforcement is provided, calculate the concrete contribution to the shear strength (Vc). Give your answer below in kN.
OP N C What is the shear resistance of a universal beam (UB) with the following dimensions [EC3 Section 6.2 Resistance of cross sections]: Cross sectional area A = 105 cm² Height h = 584.6 mm Flange thickness t = 11.4 mm Flange width b = 213.2 mm y-y Web thickness tw = 7.8 mm Root radius r = 12.7 mm Yield strength fy = 355 N/mm² Calculate the shear resistance and give your answer to the nearest whole kN. Do not include units in your answer.
View Policies Current Attempt in Progress The simply supported beam consists of a W460 x 82 structural steel wide-flange shape [E-200 GPa; 1-370 x 10 mm4]. For the loading shown, determine the beam deflection vc at point C. Assume P-62 kN, w - 28 kN/m, LAB - LBC -2.9 m. LCD - 1.9 m. P W TV D C LBC Answer: VCF LAB B mm. LCD