nsider the circuit shown in (Figure 1). Suppose that = 72, k = 15, and i, = 5 A. ure 150 is 302 30 (2 www 100 1 of 1 kis Part A Use the node-voltage method to find the magnitude of total power developed in the circuit. Express your answer to three significant figures and include the appropriate units. Pdev = Submit Part B μÀ Value Submit Request Answer 6 μÅ Pabs= Value Find the magnitude of the total power absorbed in the circuit. Express your answer to three significant figures and include the appropriate units. Request Answer Units P Pearson ? Units ?

nsider the circuit shown in (Figure 1). Suppose that = 72, k = 15, and i, = 5 A. ure 150 is 302 30 (2 www 100 1 of 1 kis Part A Use the node-voltage method to find the magnitude of total power developed in the circuit. Express your answer to three significant figures and include the appropriate units. Pdev = Submit Part B μÀ Value Submit Request Answer 6 μÅ Pabs= Value Find the magnitude of the total power absorbed in the circuit. Express your answer to three significant figures and include the appropriate units. Request Answer Units P Pearson ? Units ?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

The dioces are ideal. write the Fransfer Characteidie equati ons ( &, as a funchiar g &) Plot &o agaiwet &, imdicaling all intrcepts, slopes and Volt ope lerels. Sketch bo f bq =40 sin wt. Indicate al voltage lezels - %3D 1OK lok lov
The manimum value of the altenating wotaye and curent are 400 U and 20A respectvely s a cieritoanected to a svita supply . The ristantanerus values of the veltnge and current are 283V and 10 A respectvely of fime t=0, beth icreasing pesitively. 4) Write dan the gapressom for vwltaga and curend at pmet. b). Defermaned tha prver omsumed in the cranit. Take the velye and cunent to be ginusrida). fie P= VI end\ P = YI (PF)
Q6. What is the purpose of harmonic standards? Provide a summary of comparison of IEEE and IEC standards. Write the purpose of the following international standards shown in Table- 2: [12] Table-2 Sr No 1 IEEE-18 Standards Description 2 IEEE 518 3 IEEE 519 4 IEEE 1159 5 IEEE P1433 6. IEEE P1453 7 IEEE P1564 8 IEC61000-3-2 9 IEC 61000-4-7 10 IEC 61642 11 IEC SC77A/WG9 12 IEC SC77A/WG2
-Consider the following DT sequence, Is this signal as Power Signal or Energy signal? Determine it. * 0Snくs X [n ]= lo-n 55.n510 • ther wise Power Signal, P=85 Energy Signal, E=85 O Neither energy nor Power O Both, P=30 E=55 -Is the following signal is X(4) - Sin 3t + Sin 大t Periodic Aperiodic
0 Consider the image below. Derive an expression for E as a function of the excitation voltage E¡ and the resistances R₁ and R₂. You may have to use Ohm's law and/or Kirchhoff's laws. Ei allt R1 Eo 0 R2
9. What will be the impedance of a LR-C circuit if it has a circuit current of 3A and a supply voltage of 120V? A. 45ohm B. 50 ohm C. 40 ohm D. 35 ohm 10. A pure inductance of 100mH is connected in parallel to a 25microfarad capacitor. The network is connected to a 200V, 60Hz supply. Determine the circuits current. A. 2A B. 3.42A C. 4A D. 10A
Q2. For the circuit shown in figure (a), let the frequency is 1KHZ, and V1 = 20Vms, draw the following: 100uF C2 V1 1000UF R1 VSINE 2K A. Impedance diagram B. Voltages phasor diagram. C. Measure the voltage across R1, Vin, and the capacitors, C1, C2 us ng the oscillscope using PROTEUS software. D. Measure the current in the circuit using DMM E. From the above measurments verify your result.
For a series RLC circuit with a sinusoidal input voltage, the amplitude of the current passing through the circuit (I, in mA) is plotted as a function of frequency for two cases: Curve 1 with R1, L1. and Curve 2 with R2. L2 as shown in the next figure. The value of the capacitor used in the circuits is C=0.01 micro Farads. If the value of R2 =1600 Ohm then the input voltage (in volts) is: 7.5 25 110 Frequency H2 O a. 4 O b. 16 sin(9888 t) O c. 8 O d. 8 cos(6.28 f t) O e. 8 sin (6.28 R t)
The point form of Ampere law is given by: Select one: O a. Curi(H) = J O b. Curl(B) = I OC Curl(V) = I Od. Curl(D) = J
2_53528980697... -> For the circuit shown below, detemine the voltage of the -j10 2 capacitive reactance. -j5 0 ILOA(T) ==j102 jlon is Q 102 O 0.5L-90 52 A.
The characteristic equation of sixth order system is as below find the stability of system. + 2s° + 8s4 + 12s + 20s? + 16s + 16 = 0
Date Pags 2) A sinusoidal alteznating voltage has value of 200V and 50 Hz It cEOSses an EoMo S. a fzequency of the zeso axi in a pasitive disection when t=0. Detezmine ņ the Aime when voltage fizst teaches the instan Zenemus value of 200 V and 2) the whe time when Valtage madei mum. after passing throag its positive ualu e eeashes the value Of 141.4V.