Note: All dimensions are in mmØ 343.) A 34 mm diameter x 120 mm shafting will be turnedusing a lathe to produce a step shafting as shown in thefigure. Calculate the required (minimum) totalmachining time Tm with the following cuttingØ 3050120conditions:Step ShaftingRough Turn: V = 30 m/min; Max. Depth of Cut = 1.5 mm; Feed = 0.2 mm/revFinish Turn: V = 60 m/min; Max. Depth of Cut = 0.5 mm; Feed = 0.05 mm/revLathe available rpm: 150, 200, 250, 350, 400, 450, 500, 550, 600, 650, 700

Given:- Dinitial=34 mm,Dfinal,Rough=31 mm,Dfinal,Finish=30 mm,L=50 mm,rough turn:-V=30 mmin,depth of…

Note: All dimensions are in mm Ø 34 7. 3.) A 34 mm diameter x 120 mm shafting will be turned using a lathe to produce a step shafting as shown in the figure. Calculate the required (minimum) total machining time Tm with the following cutting conditions: 30 - 70 *-50- 120 Step Shafting Rough Turn: V = 30 m/min; Max. Depth of Cut = 1.5 mm; Feed = 0.2 mm/rev Finish Turn: V = 60 m/min; Max. Depth of Cut = 0.5 mm; Feed = 0.05 mm/rev Lathe available rpm: 150, 200, 250, 350, 400, 450, 500, 550, 600, 650, 700

Note: All dimensions are in mm Ø 34 7. 3.) A 34 mm diameter x 120 mm shafting will be turned using a lathe to produce a step shafting as shown in the figure. Calculate the required (minimum) total machining time Tm with the following cutting conditions: 30 - 70 *-50- 120 Step Shafting Rough Turn: V = 30 m/min; Max. Depth of Cut = 1.5 mm; Feed = 0.2 mm/rev Finish Turn: V = 60 m/min; Max. Depth of Cut = 0.5 mm; Feed = 0.05 mm/rev Lathe available rpm: 150, 200, 250, 350, 400, 450, 500, 550, 600, 650, 700

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 47 mm for an initial length of 154 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii) During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Total time required to complete the turning operation is 59.6 minutes
A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 47 mm for an initial length of 154 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii) During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Total time required to complete the turning operation is 59.6 minutes (a) Find number of passes to finish the entire turning operation ( (b) The actual length of the turning operation in mm ('
A mild steel specimen of Initial diameter of 30.5 mm is turned to final diameter of 27 mm for an initial length of 153 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii)During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Time required to complete one single turning operation is 3.5 minutes (a)Find number of passes to finish the entire turning operation (b) Total time required to complete the turning operation in minutes
A mild steel specimen of Initial diameter of 30.5 mm is turned to final diameter of 27 mm for an initial length of 153 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii)During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Time required to complete one single turning operation is 3.5 minutes (c) Spindle speed in in rpm (= (d) Cutting speed in m/minutes(=
A mild steel specimen of Initial diameter of 32.5 mm is turned to final diameter of 25 mm for an initial length of 154 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.3 mm/rev & Depth of cut is 0.5 mm (ii)During machining the tool's approach length is 6 mm, over run length is 3mm (iii) Time required to complete one single turning operation is 2.3 minutes (a)Find number of passes to finish the entire turning operation (b) Total time required to complete the turning operation in minutes (c) Spindle speed in in rpm (d) Cutting speed in m/minutes
A mild steel specimen of Initial diameter of 51.5 mm is turned to final diameter of 48 mm for an initial length of 151 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.1 mm/rev & Depth of cut is 0.5 mm (ii) During machining the tool's approach length is 7 mm, over run length is 2mm (iii) Total time required to complete the turning operation is 48.8 minutes (a) Find number of passes to finish the entire turning operation (b) The actual length of the turning operation in mm ( (c)The time required to complete one single turning operation in minutes (d) Spindle speed in rpm
thickness is HW3.A block of steel has a length L-600mm and a width W-450mm. The Machined 10mm, once by Peripheral Milling and once by planing Machine.Calculate :Machining time for each operation if you know the following For peripheral milling: cutting speed V =80 m/min, Feed f-0.15mm/rev, the cutter .1 diameter D =50 mm with five teeth and depth of cut d =3mm For planing: clearance on both sides c =25mm, cutting speed V =36.56 m/min, retum to .2 cutting ratio m =0.25, feed f=5 mm/stroke and depth of cut d =5 mm .Calculate Material removal rate in both processes .3 Solution
The outline of the part in figure below is to be profile milled, using a 20 mm diameter end mill with two teeth. The part is 10 mm thick. Cutting speed =125 m/min and feed = 0.10 mm/rev. Use the lower left comer of the part as the origin in the x-y axis system. The two holes in the part have already been drilled and will be used for clamping the part during milling, Write the part program in the APT format.
In a slab milling operation , L_w = 200 mm table feed = 18 mm/min, diameter of cutter = 34 mm depth of cut = 2 mm. Considering approach and overtravel to be same. The milling time in min will be?
HW3: A block of steel has a length I. = 600 mm and a width w = 450 mm, The thickness is Machined 10 mm, once by Peripheral Milling and once by Planing Machine. Calculate Machining time for each operation if you know the following: 1. For peripheral milling: cutting speed V = 80 m/min, Feed f 0.15 mm/rev, the cutter diameter D- 50 mm with five teeth and depth of cut d- 3 mm. 2. For Planing: clearance on both sides e = 25 mm, cutting speed V = 36.56 m'min, return to cutting ratio m - 0.25, feed f- 5 mm'stroke and depth of cut d- 5 mm. 3. Calculate Material removal rate in both Processes. Solution:
A cylindrical workpiece has a 14.0 in diameter and has 30 in long. It is to be turned in an engine lathe at the following cutting conditions: cutting speed = 400 ft/min, feed = 0.015 in/rev, and depth of cut = 0.150 in. Determine the time to complete one turning pass if the approach and overtravel allowances are each 0.25 in (total = 0.50 in). Note: 1 ft = 12 in
The face milling cutter of D = 200 mm used to cut a block which is 200 mm H, 1=480 mm, if f- 0.7 mm/rev is used and the overrun of the cutter is 12 mm and cutting speed 320 mm/min. Calculate the machining time. Cuttin