No. 1. (10 Pts) An aluminum pipe with a length of 60 m at a temperature of 10°C rests freely on the ground. An adjacent steel pipe at the same temperature is 5 mm longer than the aluminum pipe. (a) At what temperature (degrees Celsius) will the aluminum pipe be 15 mm longer than the steel pipe? (Assume that the coefficients of thermal expansion of aluminum and steel are aa=23x10-6/"C and as=12x10-6/°C, respectively.) (b) What is the axial stress developed in the aluminum pipe when the temperature was increased? 5 mm Aluminun Steel Figure No. 1

No. 1. (10 Pts) An aluminum pipe with a length of 60 m at a temperature of 10°C rests freely on the ground. An adjacent steel pipe at the same temperature is 5 mm longer than the aluminum pipe. (a) At what temperature (degrees Celsius) will the aluminum pipe be 15 mm longer than the steel pipe? (Assume that the coefficients of thermal expansion of aluminum and steel are aa=23x10-6/"C and as=12x10-6/°C, respectively.) (b) What is the axial stress developed in the aluminum pipe when the temperature was increased? 5 mm Aluminun Steel Figure No. 1

Sustainable Energy

2nd Edition

ISBN:9781337551663

Author:DUNLAP, Richard A.

Publisher:DUNLAP, Richard A.

Chapter8: Direct Use Of Solar Energy

Section: Chapter Questions

Problem 5P

See similar textbooks

Similar questions

An aluminum pipe has a length of 64 m at a temperature of 15°C. An adjacent steel pipe at the same temperature is 2 mm longer. At what temperature will the aluminum pipe be 6 mm longer than the steel pipe? Assume that the coefficient of thermal expansion for the aluminum is 22.5x10-6/°C and that the coefficient of thermal expansion for the steel is 12.5x10-6/°C. Answer: T₁= i °℃
A 13 in length of aluminum tubing (with E = 11.4 x 106 psi and  = 12 x 10-6 /deg F) having a cross-sectional area of 1.6 in2 is installed with “fixed” ends so that it is stress-free at 70 deg F. In operation, the tube is heated throughout to a uniform 500 deg F. Careful measurement at the higher temperature indicates that the fixed ends separate to 13.008 in. What loads are exerted on the ends of the tube, and what are the resultant stresses?
An aluminum pipe has a length of 65 m at a temperature of 16°C. An adjacent steel pipe at the same temperature is 5 mm longer than the aluminum pipe. At what temperature (in degrees Celsius) will the aluminum pipe be 14 mm longer than the steel pipe? (Assume that the coefficients of thermal expansion of aluminum and steel are a, = 23 x 10-6/°C and a = 12 x 10-6/°C, respectively. Also assume that the temperature of both pipes change equally.) °C
Q8: Consider a steel rod of fixed ends. If the temperature of the rod is increased by AT-80 °C, then the generated thermal stress (in MPa) in the rod is: (Hint: For the steel, the Young's modulus (Y) is 2x10 N/m and the coefficient of linear thermal expansion (a) is 11 x 106 ly a) 2.2 b) 176.0 c) 352 d) 776.6
1. When the force of 3 mN is applied to the plate the line AB in the liquid remains straight and has a velocity of 0.6x103 m/s. If the surface area of the plate in contact with the liquid is 0.6 m2, determine the approximate viscosity of the liquid. В в B B' 3 mN 4 mm A
An aluminum pipe with a length of 60 m at a temperature of 10°C rests freely on the ground. An adjacent steel pipe at the same temperature is 5 mm longer than the aluminum pipe. (a) At what temperature (degrees Celsius) will the aluminum pipe be 15 mm longer than the steel pipe? (Assume that the coefficients of thermal expansion of aluminum and steel are a=23x10-6/°C and as-12x10-6/ c, respectively.) (b) What is the axial stress developed in the aluminum pipe when the temperature was increased? 5 mm Aluminun Steel Figure No. 1
The aluminum tube AB of cross section has a fixed support on the base and is supported by a pin at the top of a horizontal beam supporting a load Q = 200 kN. Determine the required thickness t of the tube if its outside diameter for 100 mm and the necessary safety factor in relation to Euler buckling for n = 3.0 (assuming A = 72 GPa). I know the answer, but I cannot understand the critical charge formula. I don't know why to use the constant 2.046 in the formula, can you please show me?
An aluminum pipe has a length of 60 m at a temperature of 10° C. An adjacent steel pipe at the same temperature is 5 mm longer than the aluminum pipe. At what temperature (degrees Celsius) will the aluminum pipe be 15 mm longer than the steel pipe? (Assume that the coefficients of thermal expansion of aluminum and steel are aAL=23x 10^-6°C and as=12x10^-6° C respectively)
A prismatic bar 50°F is imbedded in a rigid concrete wall. The bar is 40 in long and has a cross-sectional area of 4 in?. What is the axial force in the bar if its temperature is raised to 100°F? Assume cocfficient of thermal expansion is 5x10%F and modulus of clectricity is 32x10° psi.
A metallic cube of 30 cm side and weighing 500 N is lowered into a tank containing two fluid layers of water and mercury. Top edge of the cube is at water surface. Determine the position of block, at Water-Mercury interface when it has reached equilibrium. (30-1) Water Interface Mercury
An aluminum pipe has a length of 75 m at a temperature of 18°C. An adjacent steel pipe at the same temperature is 0.005 m longer than the aluminum pipe. At what temperature (0C) will the aluminum pipe be 0.015 mm longer than the steel pipe? (Assume that the coefficients of thermal expansion of aluminum and steel are aa = 23 x 10–6/°C and as = 12 x 10–6/°C, respectively.)
An aluminum pipe with a length of 60 m at a temperature of 10°C rests freely on the ground. An adjacent steel pipe at the same temperature is 5 mm longer than the aluminum pipe. (a) At what temperature (degrees Celsius) will the aluminum pipe be 15 mm longer than the steel pipe? (Assume that the coefficients of thermal expansion of aluminum and steel are ca=23x10-6/°C and as=12x10-6/°C, respectively.) (b) What is the axial stress developed in the aluminum pipe when the temperature was increased? Aluminun Steel Figure No. 1 5 mm