Modern commercial airliners are largely made of aluminum, a light and strong metal. But the fact that aluminum is cheap enough that airplanes can be made out of it is a bit of historical luck. Before the discovery of the Hall-Héroult process in 1886, aluminum was as rare and expensive as gold. What would happen if airplanes had to be made of steel? The fuselage of the Boeing 777, which can carry 305 passengers, is approximately a hollow aluminum cylinder without ends, 64.0 m long, 6.2 m wide, and 2.5 mm thick (see sketch at right). The fuselage of an airplane Suppose this fuselage was made of steel (density 7.87 g/cm') instead of aluminum (density 2.70 g/cm), and let's say the average passenger has a mass of 80 kg. We'll also assume the engines can't lift any greater mass than they already do. Calculate the number of passengers that the Boeing 777 could carry if its fuselage was made of steel.

Modern commercial airliners are largely made of aluminum, a light and strong metal. But the fact that aluminum is cheap enough that airplanes can be made out of it is a bit of historical luck. Before the discovery of the Hall-Héroult process in 1886, aluminum was as rare and expensive as gold. What would happen if airplanes had to be made of steel? The fuselage of the Boeing 777, which can carry 305 passengers, is approximately a hollow aluminum cylinder without ends, 64.0 m long, 6.2 m wide, and 2.5 mm thick (see sketch at right). The fuselage of an airplane Suppose this fuselage was made of steel (density 7.87 g/cm') instead of aluminum (density 2.70 g/cm), and let's say the average passenger has a mass of 80 kg. We'll also assume the engines can't lift any greater mass than they already do. Calculate the number of passengers that the Boeing 777 could carry if its fuselage was made of steel.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A machinist was tasked to insert an aluminum piston into a steel cylinder. The inside diameters of the cylinder and of the piston are 0.500 m and 0.4998 m, respectively, at 25 ℃. To what temperature must they be heated to obtain a perfect fit?
A washer has a hole in the middle. (a) As the washer is heated, does the hole expand, shrink, or stay the same size? (b) Whichof the following is the best explanation for you prediction?I. The hole shrinks because the metal of the washer expands inward into the hole.II. The hole expands along with everything else—every dimension of the washer expands.III. The size of the hole remains the same because it is empty space, rather than metal like the washer.
If a force of 400 N is applied to a bar of titanium and an identical bar of magnesium, which would stretch more?
What are Ductile materials?
How much heavier, on average, will an aluminum-alloy tennis racquet be if it is made from titanium alloy? Obtain a tennis racquet, and take appropriate measurements to perform your analysis.
Answer is Around 5.8lb [diagram must be drawn] An automobile weighing 3900 lbs has 29-inch diameter wheels. Assuming the coefficient of rolling resistance between the tires and the road of 0.02 inch, determine the force necessary to overcome rolling friction on a level road. Answer should be in lbs
If the wrought stock material costs $60 per kg, what is the lost value due to the material removed, assuming scrap is sold for $3 per kg? Assume the density of titanium is 4.5 g/cm3. Briefly explain how you got your answer. Neglect costs of lubricant/coolant, chip handling, etc. Round your answer down to the nearest dollar.
A machinist was tasked to insert an aluminum piston into a steel cylinder. The inside diameters of the cylinder and of the piston are 0.500 m and 0.4998 m, respectively, at 25OC. To what temperature must they be heated to obtain a perfect fit?
As James orbits, he slams into a space elevator, peals himself off, and gets in. On the way down, he thinks about how much strain his legs (0.3m long) can take. If he has a mass of 45kg, and a diameter of 3cm what is the strain on each leg? Assume compact bone.
A machinist was tasked to insert an aluminum piston into a steel cylinder. The inside diameters of the cylinder and of the piston are 0.500 m and 0.4998 m, respectively, at 25 degrees Celcius. To what temperature must they be heated to obtain a perfect fit? Answer: 55.8 degrees celcius.
For 6061-T6 aluminum, estimate the maximum tensile load (kg) that can be supported if the cross-section is 1.6 mm x 6.5 mm. Which key material property must you look up (cite source; use Callister, matweb.com, or azom.com, for instance) to solve this? Show your calculations and list any assumptions or approximations that you make.
In steel alloys, what is the best choice for aircraft construction? And why?