(MO14) 4. Design a quick return mechanism with 270 cm stroke, time ratio of 3, fixed link length of 75cm and driving crank length of 97.5cm. Determine a.Range of values of L2 b.a and B c.61 and 62 d. Actual value of L2

(MO14) 4. Design a quick return mechanism with 270 cm stroke, time ratio of 3, fixed link length of 75cm and driving crank length of 97.5cm. Determine a.Range of values of L2 b.a and B c.61 and 62 d. Actual value of L2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The flexural strength and associated volume fraction porosity for two specimens of the same ceramic…

A: Given data:- Flexural strength (σ1) =100 MPa for 0.05 porosity Flexural strength (σ2) =50 MPa for…

Q: A long straight conductor has a constant current flowing to the right. A wire rectangle is in the…

A: To choose: The right option. Given: The loop is shown below

Q: The horizontal position of the 500-kg rectangular block of concrete is adjusted by the wedge under…

Q: Q5 The figure shows a shaft carrying three gears that rotates at 1150 rpm. Gear A =10kw delivers…

A: Given, NA=NB=NC= 1150rpmFor Gear A, PA= 10kw = 10×103wFor Gear C, PC=…

Q: Select the statement(s) that is (are) belong to the Carnot Principle_________ A. The efficiency…

A: As per carnot theoremthe efficiency of carnot reversible cycle ηcarrnot=1-TLTH

Q: Given are the following: T = 12kN – m L = 6m 0 = 2° G = 83 GP a Determine the smallest value of d.

A: Given data:- T=12 kN-m L=6 m θ=2° G=83 GPa To find :- the smallest value of d

Q: For the truss loaded as shown, determine the equation for the line of action of the stand-alone…

Q: 9-26. Locate the centroid of the area. 9-27. Locate the centroid y of the area. 4 ft || - 4 ft 2 X

Q: the problem related to Fundamental.7 sketches of the system showing: the respective velocity and…

Q: A solid plastic rod has a diameter of d = 33 mm and a length of L = 575 mm. An axial load of P = 32…

Q: a) The velocity component of an incompressible and 2-dimensional flow is given by Determine u = -x +…

Q: For the truss loaded as shown, determine the equation for the line of action of the stand-alone…

Q: truss is subjected to the loading shown. Determine the support reaction forces and the forces in…

Q: 3) Olive oil is cooled from 90°C to 20°C in a heat exchanger using water. Water enters the heat…

Q: For an object subjected to one or more forces, there are two force cases to consider. What are the…

A: For an object subjected to one or more forces, there are two force case to consider- Two or more…

Q: Two systems shown in fig. 3, a mass of 1 kg and the springs each with stiffness k = 20 kN/m. Under…

Q: 14.47 A 12 kW (shaft output) motor is available to run a non- cooled compressor for carbon dioxide.…

Q: * quiny 500 M T₁. T.₁. Fig.2

A: Given system is Newton’s second law, Inertia force = net restoring force

Q: Irradiation on a semi-transparent medium is at a rate of 640 W/m². If 160 W/m² of the irradiation is…

A: Given:Irradiation on a semi-transparent medium, I=640 W/m2Irradiation reflected, Ir=160…

Q: Problem 10.34 Take that a = 36 mm. (Figure 1) Figure Part A Iy = 5a Determine the moment of inertia…

Q: Refrigerant 134a circulates through the components of the system, and property data at the numbered…

A: Given:Refrigerant=R134aMass flow rate of refrigerant, m˙ref=4.6 kg/minCondition of the refrigerant…

Q: Refrigerant 134a is used as the working fluid in an OTEC power plant, which utilizes a simple…

Q: Each line of the following table gives data, in Btu, for a process of a closed system. Determine the…

Q: be developed in this member due to a uniform live load of 3 kN/m that acts on the bridge deck along…

Q: *8-60. Each block has a weight of 400 lb. Determine how far the force P can compress the spring…

A: To find: The compression of spring and force required. Given: The weight of each block isW=400 lb.…

Q: 3. A slender, rigid bar of mass 20 kg and length 4 m is rotating about its pin joint at Point A as…

Q: The higher the room temperature, the worse the performance of the air conditioner in the summer.…

A: Filter, cooling coil, membrane, and heating coil are the components of the summer air…

Q: a) Find the speed of the tape passing through the machine. b) Calculate the total acceleration at…

Q: ᴡʜᴀᴛ ɪꜱ ᴛʜᴇ ᴄʀɪᴛɪᴄᴀʟ ʟᴏᴀᴅ ᴏꜰ ᴀ ꜱᴛᴇᴇʟ ᴄᴏʟᴜᴍɴ ᴡʜᴏꜱᴇ ꜱᴜᴘᴘᴏʀᴛᴇᴅ ʟᴇɴɢᴛʜ ɪꜱ 10.7 ᴍᴇᴛᴇʀꜱ ᴀɴᴅ ᴅɪᴀᴍᴇᴛᴇʀ ᴏꜰ…

Q: Estimate (a) the maximum, and (b) the minimum thermal conductivity values (in W/m-K) for a cermet…

A: Introduction In this problem, we will compute the maximum and minimum thermal conductivities of a…

Q: Irradiation on a semi-transparent medium is at a rate of 640 W/m². If 160 W/m² of the irradiation is…

A: Irradiation that get absorbed will be, Gabs=G-Gtr-Gref =640-130-160Gabs=350 W/m2 Absorptive…

Q: ALLOYS OF NICKEL Examples : Application or Uses: Reference :

Q: Problem-5: A Plunger is fitted to a vertical pipe filled with water. The lower end of the pipe is…

A: Givena=5 m/s2hatm=10mhv=2mg=10 m/s2

Q: Why does intercooling reduce work in a comprssor (such as in the Brayton cycle), but it doesn't…

A: The Brayton cycle and the Rankine cycle vary in that the former uses a liquid as one of its…

Q: A shaft 70-mm in diameter is being pushed at a speed of 400mm/s through a bearing sleeve 70.2-mm in…

Q: 5. A solid sphere of radius 0.3 m and mass 5 kg rolls down the incline without slipping as shown in…

A: To find: The acceleration and angular acceleration. Given: The mass of the sphere is m=5 kg. The…

Q: T₂ 30% 7₁ 60°

A: Free body diagram:- it is drawn by isolating the object from the surrounding and mentioning all the…

Q: A chamber wall (1m x 2m) has an inside temperature of -4°C. The outside temperature is 22°C. The…

A: Given:Area of the wall, A=1m*2m=2 m2Inside temperature, Ti=-4oCOutside temperature, To=22oCThickness…

Q: A cast-iron bar with a square cross-section of 50 mm is reinforced by placing tw steel plates 50 mm…

A: Given data as per the question Length of bar = 2 m Sudden applied load = 100 kN

Q: Calculate the pressure of the air in the sealed tank shown in Fig. 6.25 that would cause the…

Q: (4.23) Air is compressed at steady state from 1 bar, 300 K, to 6 bars, 440 K with a mass flow rate…

Q: Rainwater flows through the galvanized iron downspout shown in the figure below at a rate of 0.009…

A: We have to determine the radius of the cross-section area of downspout. This problem require the…

Q: For an air conditioner, if QH = 600.00 kJ, and QL = 350.00 kJ, then the coefficient

A: Given Source heat, QH = 600 kJ Sink heat, QL = 350 kJ Find COPAC

Q: A vertical 2-m-high and 5-m-wide double-pane window consists of two sheets of glass separated by a…

Q: A) Plot the page 265 of the Book, for the following sets of data: forced-undamped vibration response…

A: Given data: Find: (a) Plot the forced-undamped vibration response of a spring-mass system (b)…

Q: A large blower for a furnace delivers 47 000 ft/min (CFM) of air having a specific weight of 0.075…

A: Given: V˙ =47000 ft3/min γ=0.075 lb/ft³ To find: W˙ and m˙

Q: Determine the value of F that will cause a 100 kg block to move. The coefficient of static friction…

A: Given data:- mass of the block(m)=100 kg μ=0.25 angle of force F=20° To find:- Magnitude of the…

Q: How do you calculate the pressure in a horizontal pipe given the pipe's radius, the liquid's flow…

Q: Select the picture that shows the process of a refrigerator_________

Q: The guy wires AB and AC are attached to the top of the transmission tower. The tension in cable AB…

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

write in hand written

(MO14) 4. Design a quick return mechanism with 270 cm stroke, time ratio of 3, fixed link
length of 75cm and driving crank length of 97.5cm. Determine
a.Range of values of L2
b.a and B
c.o1 and 62
d.Actual value of L2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Design a quick return mechanism with 2400 mm stroke, time of forward stroke is 3s,return stroke time is 1s, fixed link length of 50 cm and driving crank length of 80cm.Determine a.Range of values of L2b.α and βc.ϕ1 and ϕ2d.Actual value of L2
A offset crank-slider mechanism is used in a conveyor loading device. Find the crank length in mm required to generate this motion. Use the design parameters specified below. (Note: A is the crank pivot; C is the coupler-slider joint; B is the coupler-crank joint). - CBDC: 107 mm below and 140 mm to right of A (Note: BDC=Bottom-Dead-Center) - Stroke: 52 mm along a 42° incline (This direction: /. Not this direction: \)
find average piston velocity in each direction ( between limiting positions) for an off-set slider crank mechanism. The crank length is 2". The connecting rod length is 4 " and the offset is 1". the crank speed is 3000 rpm CW.
1. Design a crank-rocker linkage that will move the rocker link between two extreme positions 45 de apart. The rocker should take twice the time to moving in one direction that it takes moving in the other. somyb\\; eqrad no malieb uroy dont elle est sor oldnoba mare ono mol foque (do iliw now wodor 00. aasbois.oved nov 2. If the fourbar linkage designed in question 1 is non-grashof, list two ways in which you would alter the design so that the crank is able to rotate.
Design of Slider-Crank Mechanisms For Problems 5-11 through 5-18, design a slider-crank mechanism with a time ratio of Q, stroke of | AR4lmax and time per cycle of t. Use either the graphical or analytical method. Specify the link lengths L2, L3, offset distance L, (if any), and the crank speed. Q = 1; IARlmax = 0.9mm; t = 0.4 s. Q = 1.15; IAR4lmax = 1.2 in.; t = 0.014 s. Q = 1.20; IAR4lmax = 0.375 in.; t = 0.025 s.
find average piston velocity in each direction ( between limiting positions) for an off-set slider crank mechanism. The crank length is 2". The connecting rod length is 4 " and the offset is 1". the crank speed is 3000 rpm CW. Answers are given, I need a help for to know how to draw and solve such a question
|design a simple piston-like crank-slider mechanism that looks similar to the Figure 4 (not to scale). The centre of the crank and the slider are aligned vertically to each other. It has already been determined that the crank radius (O2A) must be 25mm, while the slider block is in a square shape of 20 mm by 20 mm. The highest position of the slider (Hmax), which is the furthest vertical distance of the slider from the centre of the crank, must be 92 mm. Based on the given design parameters, your task is to determine the suitable couple length (AB) and the lowest position of the slider (Hmin). Your superior has asked you to present the results graphically. 20 Slider 10 20 H Crank O2 Figure 4
500 mm B B2 A2 O2, 61.9292 X-line The slider-crank mechanism has a stroke of 500 mm. The required advance-to-return ratio is 1.80. The crank angle during the advance stroke (a), crank angle during the return stroke (B), crank link length (r2), and coupler length (ra) is. (See Theory of Machines and Mechanism, 5th Edition, Problem 1.31) (NOTE: Use the angle for the X-Line as shown) (a) a=231.43°, B=128.57°, r2-301.872 mm, r3=412.751 mm (b) a=128.57°, B=231.43°, r2=223.875 mm, r3=340.409 mm (c) a=231.43°, B=128.57°, r2-223.875 mm, r3-340.409 mm (d) a=128.57°, B=231.43°, r2=191.751 mm, r3-387.233 mm
Find the average piston velocity (between limiting positions) for an in-line slider-crank mechanism. The crank length is 2inch, and the crank rotates at 3000rev/min.
Figure 3 shows a quick return mechanism, which consists of a crank AB, a slider block B and a slotted link CD. (Given wAR = 3.5 rad s'', asn = 6 rad s², ocD= 4.5 rad s' a = 0.15 m, l= 0.35 m, 0 = 35° and - 35°.) (a) Determine the velocity of the slider block B. (b) Determine the angular acceleration of link CD (acD). AB Figure 3: Quick return mechanism
Aim: To conduct a full kinematic analysis and calculate dynamic reaction forces in a linkage mechanism, calculate instantaneous torque, required to drive the mechanism and to present the results of the case study in a clear reporting format. Introduction: Figure 1 shows a pumpjack operating at an oil well. Its representation as a linkage is also shown in Figure 1. The pumpjack is driven by a motor attached to crank OA. A constant torque T is applied to the crank and the crank rotates at a constant angular velocity ???. A force P is applied vertically downwards at the end of the walking beam BD, which has its centre of mass at point G. To design the mechanism, a careful kinematic analysis of the mechanism needs to be conducted. To avoid mechanical failure and to provide adequate support to the mechanism, the engineer needs to analyse the reaction forces in the joints. Masses of links OA and AB are assumed to be smaller in comparison with the mass of BD and are ignored in the analysis.…
3. Design a slider-crank mechanism with a time ratio of Q=1.25, stroke of AR4lmax=2.75 in., and time per cycle of t=0.6 sec. Find the imbalance angle, link lengths, and the crank speed.