MHVIE A: Find the original quantities of cement and water for the following situation of a hydrated cement paste. (Assume that the reaction occurred in a sailed container): V,= 30.8ml, W12 ml, unhydrated cement 20 ml, total voids= 37.5ml and the degree of hydration = 50%. !3!

MHVIE A: Find the original quantities of cement and water for the following situation of a hydrated cement paste. (Assume that the reaction occurred in a sailed container): V,= 30.8ml, W12 ml, unhydrated cement 20 ml, total voids= 37.5ml and the degree of hydration = 50%. !3!

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The cement sample was put in the pan and weigh it on the triple beam balance before transferring it…

A: Fineness of Cement Test : We know that cement hydrates when cement is mixed with the water and a…

Q: For the given amount of (weight of cement =120gm and w/c ratio=0.48, degree of hydration=50%), the…

A: To determine the volume of hydrated cement. Given, Total weight of dry cement, Wtc = 120 gm…

Q: 8) For the following cements, answer the following questions: Cement A Cement B 50 20 C3S (%) C2S…

A: Given-

Q: Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit…

A: aTrial-1γd1=W2-W1V=69.6-20.3 lb0.5ft3=98.6lbft3Trial-2γd2=W2-W1V=68.2-20.3…

Q: 8. What is the maximum allowable limit of Materials Finer Than 75 Mm (No. 200) Sieve in Coarse…

A: 8. What is the maximum allowable limit of Materials Finer Than 75 Mm (No. 200) Sieve in Coarse…

Q: Compute for the concrete mix proportion for a 6" diameter concrete cylinder mold with 12" height and…

Q: 35,000 units of CHB, how many samples for moisture content determination only? 2. You have 25T-25mm…

A: 1. 35,000 units of CHB, how many samples for moisture content determination only? 2. You have…

Q: Design a concrete mix for the following performances and ingredients: • Characteristic compressive…

A: Given data- Characteristic compressive strength 50 N/mm2 at 7 days.Defective rate 1 % Standard…

Q: WEIGHT OF RETAINED FINE AGGREGATES (g) SIEVE SIZE TRIAL 1 TRIAL 2 TRIAL 3 AVERAGE 4.75 mm 14 10 12…

Q: Using Nominal Mix Design, calculate the individual quantity of cement, sand, gravel, and water for…

A: Let the grade of concrete be M20, that is cement:Sand:Aggregate=1:1.5:3 We will find the quantity of…

Q: WEIGHT OF RETAINED FINE AGGREGATES (g) SIEVE SIZE TRIAL 1 TRIAL 2 TRIAL 3 AVERAGE 4.75 mm 14 10 12…

A: Given Data: To Determine Fineness modulus of the Fine Aggregate Sample.

Q: Given the % Cum Pass made on a fine aggregates: Sieve size mm 9.5 4.75 2.36 1.18 0.6 0.3 0.15 %…

A: It is required to determine the % cumulative retained. % Cumulative retained=100-% cumulative…

Q: What can you conclude if the specific gravity of hydraulic cement I acquired is 3.14? How this will…

A: Step: 1 Specific gravity (Gs'): - It is defined as the ratio of density of any given substance to…

Q: 1- The result of sieve analysis of three aggregate samples (A, B, and C) are given below. a) Design…

A: Solution Given Data dmax= 16 mm

Q: Q1. Fill the remaining columns for the sieve analysis data given in the table Weight of Empty…

A: Note: Since you have asked multiple questions, we will solve the first question for you. If you want…

Q: contractor needs 403 m3 of aggregate material for a highway construction project. The required dry…

Q: 21. Estimate the number of bags of cement for the concrete slab on fill, if Class C mix ratio…

Q: Strength requirements, in MPa – 30.68 Mpa Water cement ratio, in decimal – 0.45 Coarse aggregate…

A: Solution: Design of concrete mix for M24 grade The mean strength; fm=fmin+ks=24+1.64x4=30.56 Mpa…

Q: The proposed mixture has the following details: (1: 1.5: 3) by mass, w/c = 0.5, and concrete fresh…

Q: TABLE 1-2 CONCRETE PROPORTION Cement Sand Gravel Class 40 kg. / Bag 50 kg. / Bag cum Mixture cu.m.…

Q: Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit…

A: The given data is: Volume of bucket = 1/2 ft3 Weight of Empty Bucket = 20.3 lb Weight of bucket…

Q: WEIGHT OF RETAINED FINE AGGREGATES (g) SIEVE SIZE TRIAL 1 TRIAL 2 TRIAL 3 AVERAGE 4.75 mm 2.36 mm…

Q: Table 1 CONCRETE PROPORTION Mixture Proportion Cement in Bag Sand Gravel 50 kg Class AA 40 kg cu. m.…

Q: A sieve analysis test was performed on a sample of aggregate and produced the results shown in…

A: Following table containing Sieve no & amount retained of the soil sample is given: It is…

Q: Calculate the density and the yield of cement slurry produced. ii. What is the volume of water in…

Q: A simple platform having a stair will be constructed, as an estimator, your boss gave you an…

A: Concrete construction classes are of four types: Class-AA, Class-A, Class-B, and Class-C. Based on…

Q: It is required to find the unit of weight, yield, and the quantity of cement for a concrete mix in a…

Q: Calculate the sieve analysis shown in Table P5.20, and plot on a 0.45 power gra- dation chart. What…

A: The given table is shown below:

Q: Highways Engineering Example2: Determine percentages air voids and voids filled with binder to…

Q: Prepare concrete with 290 kg/m cement dosage, with a water-cement ratio of 0.44! How many (in kg) of…

A: Percentage air content = 0.02*57.9= 1.158 m3. Volume of materials required= 57.9-1.158=56.742 m3…

Q: (B) Determine the volume of the products of hydration of a mix contains 110 gm cement, 35 gm water…

A: cement weight=110gm water weight=35gm assume specific gravity of water=1 specific gravity of…

Q: SITUATION 9: On the pouring the slab of a certain restroom has the following specifications:…

Q: Q1 /Choose the correct answer. 1- hydration of C2S is a) High rate of temperature rate of…

Q: a) Cement brand b) Cement – water ratio c) Aggregates physical appearance d)…

A: In this question effect of various factors on strength is asked

Q: Given properties of cement, sand and gravel is presented in the table below: Specific Density,…

Q: SITUATION 2: The ground floor of a residential house has an area of 200 square meters. The plan…

Q: 2.49 Calculate the Bogue composition of the cements with the oxide com- position given below. Oxide…

A: Given:- The Oxide composition for cement A, cement B, and cement C is given below To determine:- The…

Q: H.W: calculate the volume of products hydration for 126g cement and 60ml of water cured in a sealed…

Q: Mixture Proportion Cement in Bag Sand Gravel Class 40 kg 50 kg cu. m. cu. m. .50 .50 AA 1:1½:3 12.0…

A: Area of concrete block from top view is 12*5 + 4.5*4.5 + 0.5*3*4.5 + 5*4.5 = 109.5 sq.m Volume of…

Q: Water defined by the following analysis is to be softened by excess lime treatment in a two- stage…

A: Solution: Consider the table: Compound Mg/L Equivalent weight M/L CO2 4.5 22 0.204 Mg2+ 37…

Q: unit cost of river sand per cubic meter is 899, while the total cost is 1348.50. Determine the total…

A: Given Cost of sand per cubic meter of concrete = 899 Total cost of sand =1348.5 Here the total…

Q: clay material containing a high percentage of gypsum was used in the manufacture of bricks through…

A: Brick is one of clay material substance the major construction material. since from the very old…

Q: H.W Q1) Assume we have 100 gram of cement within a closed tube, so that there is no water movement…

A: The given data is: Weight of dry cement actually hydrated, Wcah=100 g The volume of dry cement…

Q: Calculate the quantity of Cement, Sand, Gravel and Water for the given solid as shown and the…

Q: Calculate the slump of fresh concrete mix if you know: 1. W/C = 0.47 2. Sand = 648 Kg/m3. 3. Gravel…

Q: Using Nominal Mix Design, calculate the individual quantity of cement, sand, gravel, and water for…

Q: "A sieve analysis test was performed on a sample of fine aggregate and produced the following…

A: Sr. No. Sieve (mm) Amount Retained (gm) % Retained Cumulative %retained % Passing 1…

Q: determine the effective specific gravity of aggregates. DATA: Specific Gravity: Fine Agg = 2.603…

Q: (a) Explain how the following factors affect construction material choice: (i) resource utilization…

Q: 20 Choose the amount of cement in -2 tons and fine aggregate (sand) in cubic meters needed to pour…

A: Given length of road, L = 1 km = 1000 m Width of road, b = 10 m Thickness of road, h = 0.2 m Density…

Question

A: Find theforiginal quantities of cement and water for the following situation of a hydrated cement
paste. (Assume that the reaction occurred in a sailed container): V= 30.8ml, We= 12 ml, unhydrated
cement 20 ml , total voids= 37.5ml and the degree of hydration = 50%.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the given amount of (weight of cement=120g, degree of hydration=100% and w/c ratio=0.40), the amount volume of gel water equal to *
The cement content of a concrete is 375 kg/m3 and the w/c ratio is 0.46. At a specific moment of the cement hydration, the degree of hydration is 0.80. Calculate the volume (dm/m³) of the following: (i) chemically bound water, (ii) gel water and (iii) capillary water A concrete sample was extracted from a structure and dried at 105 °C in which 80 kg/m3 of water evaporated. The degree of hydration (a) was determined to be 0.5. The mix design of the concrete was 1:6.0:0.6 (Cement:Aggregates:Water mix ratio by weight) and the target air content was 3 %. a) How much of the water had been evaporated prior to drying at 105°C? b) What were the volume of (i) un-hydrated cement, (ii) solid part of cement gel, (iii) gel water, (iv) contraction pores, and (v) capillary pores at the time of sampling?
please provide step by step solutions and draw the lever on the graph as well. i know the answers. (c) About 1250 C (d) Fe3C, cementite (e) About 0.7 wt% C, about 72% (f) About 40%, no. (h) Draw the microstructure of a 1.5 wt.% C material that has been heated to 1200 C and then slowly cooled to 600 C. Clearly label all phases.
If the degree of hydration=55% and the weight of cement =100gm, the volume of gel water equal to *
Design a concrete mix according to the following conditions: Design Specifications Concrete ramp (not reinforced) Slab thickness =270 mm Design strength (fc) = 25.5 MPa Standard deviation s= 1.86 MPa on 200 specimens Environment = Severe exposure to freeze-thaw and de-icing chemicals Slump = 50 mm Materials Available Cement: Type GU; specific gravity 3.15 Admixture: Air entraining admixture 8 ml/1% air/100 kg cement . Coarse Aggregate: Nominal maximum size = 37.5 mm Type = Crushed stone Bulk oven-dry specific gravity = 2.63 Absorption = 2.1% Oven-dry rodded density = 1755 kg/m3 Moisture content = 1.5% Fine Aggregate Type = Natural sand Bulk oven-dry specific gravity = 2.55 Absorption = 3.1% Moisture content = 4.3% Fineness modulus = 2.40
Q1: Prepare mix design for given data • The 28-day compressive strength should be 34 MPa, The slump should be between 75 mm and 100 mm and the maximum aggregate size should not exceed 19 mm The properties of the materials are as follows: • Cement : Type I, specific gravity = 3.15 • Coarse Aggregate: Bulk specific gravity= 2.65; absorption capacity = 0.5%; dry-rodded unit weight = 1605 kg/m3, surface moisture = 1% • Fine Aggregate: Bulk specific gravity= 2.60; absorption capacity = 1.1%; fineness modulus = 2.70; surface moisture = 3%
Second Section The composition of a certain brand of cement is given (C3S = 53.0%, C2S = 18.0%, C3A=12.0% and C4AF = 8.0%) the type of cement is * Sulphate resisting cement Rapid hardening cement Ordinary Portland cement Low heat cement For the If the chemical composition of cement is as follows (CaO=60%, SIO2 =25.6%, AI203= 3.8%, MgO=4%, SO3=2.1%, C4AF=13.7%) the type of cement is * White cement None of the above Expansive cement Pozzolanic cement
In designing a concrete mix, if the amount of mixing water is estimated at W = 185 Kg/m, the SSD weight of the coarse aggregate is 1045 Kg/m, and the SSD weight of the fine aggregate is 617 Kg/m. The coarse aggregate has a moisture content of 1% and an absorption capacity of 2%. The fine aggregate has a moisture content of 2% and an absorption capacity of 5%. The adjusted weight of mixing water (in Kg/m³) is: O 177 O 214 156 193 O 172 O O O O O
A concrete mix has a ratio os 1:2:4 by mass. The properties of thematerials to be used are tabulated below.MATERIALS. SPECIFIC GRAVITYCEMENT 3.33SAND 2.65GRAVEL 2.67Cement weighs 40 kg per bag. Use 24 liters of water per bag of cement Compute the volume of cement solids per bag of cement in cu m.Compute for the required volume of sand solids per bag of cement.Compute for the volume of concrete that can be produced per bag of cement 0.1
A concrete mix includes the following ingredients per cubic meter: a. Cement = 400 kg b. Water = 176 kg c. No admixture Table P6.30 shows possible changes that can be made to the mix ingredi- ents. Indicate in the appropriate boxes in the table what will happen in each case for the workability and the ultimate compressive strength as increase, decrease, or approximately the same.
a. For an aggregate sample, if you know that the apparent relative density is 2.72 and the water absorption is 1.2%. The dry mass of the aggregate is 514 gm. Find the bulk and saturated surface dry (SSD) relative density values? b. Why does the maximum size of aggregate depend on the clear spacing between bars? Show with a simple sketch. Note: Please answer both a and b... Please answer the both questions.. I don't want single b answer.. thank you
Complete the sieve examination table for aggregates below and calculate the fineness coefficient