Hi .. This is simulation starting synchronous motor in matlab 2012 who can I find the power factor by use this simulation and what is the elemen add to find the power factor Mechanical load-0.5Vf sourcePmRate LimiterVf(pu)>= 0.99 IS)400 V; 50 HzSynchronous M achinepu Fundamental60 kVA 400 V 50 HzThree-Phase BreakerLatchR_startVabc5kWFromVabc machineElectromagnetic torque Te (pu)>Vf(pu)Apply feld voltageScopeContinuousStarting a Synchronous Motor?powerguiDouble click for info

as power factor is given by PF=apparent power real power and apparent power=real power2+reactive…

Mechanical load -0.5 V source Pm A Rate Limiter Vf(pu) >= 0.99 s) 400 V. 50 Hz Synchronous Machine pu Fundamental 60 kVA 400 V 50 Hz Three-Phase Breaker Latch Rstart Vabc) 5kW From Vabc machine Electromagretic brque Te (pu) Vf(pu) Apply feld voltage Scope Continuous Starting a Synchronous Motor powergui Double click for info

Mechanical load -0.5 V source Pm A Rate Limiter Vf(pu) >= 0.99 s) 400 V. 50 Hz Synchronous Machine pu Fundamental 60 kVA 400 V 50 Hz Three-Phase Breaker Latch Rstart Vabc) 5kW From Vabc machine Electromagretic brque Te (pu) Vf(pu) Apply feld voltage Scope Continuous Starting a Synchronous Motor powergui Double click for info

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter7: Symmetrical Faults

Section: Chapter Questions

Problem 7.21MCQ

See similar textbooks

Similar questions

The step down DC chopper uses DC source voltage V(dc) = 200 V and resistive load impedance of 10 ohm. The duty cycle is 0.4 the voltage drop across the switch may be taken as zero, Calculate : (a) Average and RMS value of output voltage. (b) Average and RMS value of output current.
in lab winding schemes, The-2 induced emf in a coil is emf in .coil for wave winding a) greater than b) smaller than O c) equal to O
The ripple factor for pure dc is Answer:
In capacitive AC circuit voltage is leading current O a. True O b. False
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diodeshave? (Use constant voltage drop model for the Silicon diode) D IN4001 OV 10 kN IN4001 DELL
Protection Schemes for Series Capacitor (compensation )
Single phase control AC voltage regulator with an inductive load connected with AC power Vs-220 vrms F-120 Hz. resistance is 1.50 L-5mH and phase angle is 45 determine the P.F. 0.69 O 0.65 O 0.45 O 0.95
3-9 An rms ac voltmeter and a peak-to-peak-reading ac voltmeter are to be used to determine whether three ac signals are sinusoidal. Deter. mine whether the signals are sinusoidal if the following readings are obtained First signal Second signal Third signal peak-to-peak reading = 35.26 V rms reading. - 12.00 V peak-to-peak reading - 11.31 V rms reading = 4.00 V peak-to-peak reading = 25.00 V rms reading -8.83 V
13. The transformer in a large welder provides single-phase ac output at 30 V, 50 Hz. An SCR bridge is used to control the welder. A large inductor helps to maintain a welding arc. a. What phase delay angle should be used to set an initial voltage of 25 Vac? b. The phase angle drops back once the arc has formed. What phase delay angle is needed for 8 Vdc output?
The brushes width in Wave winding is equal to a. 1.5 commutator segments. b. 1 of commutator segments. c. 1.25 commutator segments.
4) Determine the value of voltage across resistor and capacitor5) Convert in rms values
In DC choppers the wave forms for input and output voltages are respectively a. both discontinuous b. discontinuous,continuous c. both continuous d. continuous,discontinuous