Match column A with Column B. Given: Samples were spotted on the TLC plate and after performing the experiment, the following were obtained: Component A, Rf = 0.2 B, Rf = 0.5 C, Rf = 0.8 Which is the most polar? A. Component A v Which can dissolve in water? B. Component B Which has affinity to the stationary phase? c. Component C Which has affinity to mobile phase? Which is the least polar Which can dissolve in organic compounds? v Which component is slightly hydrophobic and hydrophilic? Activa

Match column A with Column B. Given: Samples were spotted on the TLC plate and after performing the experiment, the following were obtained: Component A, Rf = 0.2 B, Rf = 0.5 C, Rf = 0.8 Which is the most polar? A. Component A v Which can dissolve in water? B. Component B Which has affinity to the stationary phase? c. Component C Which has affinity to mobile phase? Which is the least polar Which can dissolve in organic compounds? v Which component is slightly hydrophobic and hydrophilic? Activa

Principles of Instrumental Analysis

7th Edition

ISBN:9781305577213

Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Publisher:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Chapter16: An Introduction To Infrared Spectrometry

Section: Chapter Questions

Problem 16.14QAP

See similar textbooks

Similar questions

Imagine you are trying to analyze Zn2* in a multivitamin. 7. Discuss with your group: what are other ions which may be in a multivitamin that could make the quantitation of Zn2+ difficult? analyte signal = F (standard signal S samp = KĄCA Sspike = kA (CAVotVad Vo V std + Cstd [analyte] [standard] Vo+V std
True of false? 1. Raman Spectroscopy can be used in the airport to detect the presence of Alcohol in the bags? 2. Furnace atomisation is used when the concentration of the sample in the ppb level? 3. 24 karat of gold mean the percent of gold in the object is 75%?
How do I solve for [FeSCN2+] heres the formula they provided me and my data but I would like steps on how to solve it and what data I should be using to solve for it u can use any fake numbers you need to help me understand ! I'm confused only by the absorbance part , what number am I using for the absorbance? Is it Fe3+ added to ScN- absorbance values ? also e = 202 and L = 1.0
What are the advantages of using the KBr in IR spectroscopic sample preparation? Please shortly write at your own words. (4-5 lines maximum ).
Why is it important to acquire a reference spectrum and subtract it from the sample’s spectrum? Why are quartz cuvettes better for UV-visible absorption spectroscopy than polystyrene cuvettes, especially at lower wavelengths (UV)? What would happen if you put too much of a compound in the cuvette during the spectral measurement? Why is it important to avoid any scratch on the cuvette? Could you use a compact fluorescent light (CFL) bulb to perform UV-visible absorption spectroscopy? Why/why not?
8. Why are higher resolution monochromators found in ICP-OES spectrometers than in flame AAS spectrometers?
Below is the Electrospray ionization mass spectrum of a compound; what is the exact mass of this compound? 100- 80 60 40 20 10 95 96 97 98 MS-NW-5593 20 fpoy.ql.ppppplıyo 30 40 50 60 70 80 90 100 110 TTTTT 120
5. Can you explain why not all CuSO4 solution concentrations can be determined from spectrophotometer readings using wavelength absorption at 700 nm? Are there readings that are inaccurate? If not, why not, and if yes, why?
1. True or False a. UV-Vis spectroscopy normally reports data in the from of bands rather than single peaks because of overlapping electronic transitions that are being recorded by the detector. (T/F) b. When using linear regression to translate absorption data using Beer's Law, the y-intercept (+b) of the linear equation represents the path length. (T/F) c. Phosphorescent materials give a glowing effect because the electrons remain at an excited state for much longer, which is the cause for the "glow". (T/F)
Please complete Table 2 and show the calculations for protein concentration and the concentration of the undiluted sample. a). Using Excel software, enter data from Table 1 to plot a standard curve (corrected average absorbance on Y-axis and protein concentrations on X-axis). The standard curve must contain correct labels on both axes. b). From the standard curve, obtain a best fit line and equation. c). Use the best fit equation and data from Table 2 to find the concentrations of proteins in sample A2-D2 and E1. [onto your plotted standard curve, indicate where A595 of A2-D2 and E1 are located] d). Calculate the concentrations of proteins in undiluted samples A to E. Thank you very much.
Calculate the molar concentration for a sample dye solution with a measured absorbance of 0.304. (Hint: Use linear regression analysis.). Final answer in 3 significant figures.
Why is CCL4 preferred over acetone as a solvent in running IR spectra of solids?