M 12 m. 60° Sin. 40 lb Problem 03.114.b - Location of the resultant force Locate the points where the line of action of the resultant intersects the line AB and line BC. Take M-90.00 lb-in. 6.87 in. to the left of B. The line of action of the resultant intersects line AB at a= The line of action of the resultant intersects line BC at c= 2.91 in. below B.

M 12 m. 60° Sin. 40 lb Problem 03.114.b - Location of the resultant force Locate the points where the line of action of the resultant intersects the line AB and line BC. Take M-90.00 lb-in. 6.87 in. to the left of B. The line of action of the resultant intersects line AB at a= The line of action of the resultant intersects line BC at c= 2.91 in. below B.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the forces acting on the beam shown in Figure 3.1c, determine the location of the equivalent resultant force with reference to point A in m. Given a = 2.5, b = 2, P1 = 20, w1 %3D = 5 and w2 = 9. (Note: Prefix the answer with negative sign "." if the location is to the left of the reference point. E.g. if the location of the equivalent resultant force is located between points A and B, or to the left of point B by 1.2m, the answer should be "-1.2" with reference to point B) P, kN W2 kN/m W, kN/m A a m b m Figure 3.1c
Determine the intenal normal force, shear force, and moment at point Cin the simply supported beam. Point Cis located just to the right of the 250 Nm couple moment. * Make sure to add units out of ** Your answer should look like this: Ne =, Vc=. Mc 100 N 5 m 300 N/m A 35 250 N.m 8 m 4 m 4 m 40 N Answer
The 16 x 22 x 25-mm rubber blocks shown are used in a double U shear mount to isolate the vibration of a machine from its supports. An applied load of P = 238 N causes the upper frame to be deflected downward by 4 mm. Determine the shear modulus G of the rubber blocks. Double U anti-vibration shear mount 25 Rubber block dimensions Shear deformation of blocks O 0.745 MPa O 0.883 MPa O 1.140 MPa
A light fixture of negligible mass, has three applied forces acting on it as shown. |F,| = 4 kN 1.2 m 1.2 m 1.2 m 2.8 m |F, = 6 kN y 45° |F,| = 5 kN %3D Using the coordinate system shown, determine the components of vector F2 = Fxi + F,J + F,k (Answer in Kilo Newtons) Choose... + Fy Choose... F2 Choose...
PROBLEM NO. 1 For the beam shown below, determine the following using double integration method. 600 N/m 200 N/m 200 N/m В 2 m 3 m 0.8 mp.8 m E = 12 000 MPa | = 50 x 10 ° mm A. Reaction at left support. B. Deflection at point 2.0m from left support. C. Deflection at point 3.0m from left support.
The figure shows a cantilever of length L= 4 m consisting of steel angles size of 100 x 100 × 12 mm mounted back to back. The cantilever is subjected to a point load P= 1500 N acting at a = 2.5 m and a distributed load w= 1100 N-m-. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. P a В Find the deflection at B. The deflection at B is – 4.46 mm.
3. Determine the resultant of the following forces acting at 0 as shown in the figure. B= 300 N. %3D A = 200 N 45 30° O\60 C= 250 N 140 24
A light fixture of negligible mass, has three applied forces acting on it as shown. |F,| = 4 kN %3D 1.2 m 1.2 m 1.2 m 2.8 m |F,| = 6 kN y 45° |F = 5 kN Using the coordinate system shown, determine the components of vector F = Fxi + F,J +F,k (Answer in Kilo Newtons) Fy F2 F,
A beam supported by three identical springs at points A,B,C (see figure). Given that flexural of rigidity of the beam, EI= 2.029X1011 N.mm2 ; spring constant,k = 1471.5N/mm, w=116N/mm All dimensions are in mm. 1. What is the reaction for at point A,B and C? 2. What is the deflection at point B? 3. Please draw shear-force and bending moment diagram.
Q3: Three forces are acting on a steel plate with 4m length by 4m width shown in figure. These three forces are required to cause a horizontal resultant acting through point A. If F = 405N, 1) The value of horizontal resultant R is: F E A B
Figure 1 shows a beam supported at A and B. The beam has a point load of 4 kN at C. Calculate the deflection at C using the conjugate beam method (E = 200 GPa and I = 420 x 106 mm*). 4 kN A в 20 m 10 m
Suppose we have a uniform beam that is 4.46 metres long has a flexural rigidity of 25079Nm². Find the deflection of the beam in millimetres if the beam is under a load of f(x) = 7.00(x + 3.3252) (5.02 - – x). answers. N and is supported with simple supports at both ends. Fill out the table below with your x-coordinate x = 0.54 x = 1.07 x 2.19 = m Deflection (mm) y(x) = Skipped y(x) = Skipped y(x) = Skipped x = 3.34 y(x) = Skipped x = 4.19 y(x) = Skipped Enter as many decimal places as your calculator allows (8 to 10). Your answer must be within +0.0005 of the correct answer to be considered correct.