Let us consider two water columns at different temperatures, one being at 40oC and the other being at 20oC. As both the water columns are separated by a glass wall of area 1m by 2m and a thickness of 0.003m. Calculate the amount of heat transfer. (Thermal Conductivity of glass is 1.4 W/mK)

Let us consider two water columns at different temperatures, one being at 40oC and the other being at 20oC. As both the water columns are separated by a glass wall of area 1m by 2m and a thickness of 0.003m. Calculate the amount of heat transfer. (Thermal Conductivity of glass is 1.4 W/mK)

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.36P

See similar textbooks

Related questions

Q: 2.122 The homogeneous gate shown in Fig. P2.122 consists of one quarter of a circular cylinder and…

A: To findDetermine the weight of the gate per meter of length.Givenwater depth = 4 mwidth of the gate…

Q: 3. The system in Problem 2 assumes the AT for heat transfer between the refrigeration system…

A: Given:The condenser temperature, The evaporator temperature, The environmental temperature, The…

Q: how much total force does the pulley system shown below apply to the ceiling? the mass hanging from…

A: Ans Given Now draw the FBD of the hanging pulley asNow net force in vertical direction is

Q: The control rod AP exerts a force F on the sector as shown. Determine both the x-y and the n-t…

Q: The motion of a particle is defined by the equations x=(+1)² and y = 4(t+1)2, where x and y are…

A: The equation of particle is

Q: 6. An old automobile exhibits a vertical oscillating displacement of maximum amplitude 7 cm and an…

A: For the solution refer below images.

Q: 7/50 The wheel of radius r is free to rotate about the bent axle Co which turns about the vertical…

A: Given :The rate of vertical axis turning is

Q: Air with the properties below enters a converging duct. Does the flow reach choked conditions? U =…

A: Hi, As per the rules, we can provide the solution for only first question so please resubmit your…

Q: (a) Derive planar density expressions for BCC (100) and (110) planes in terms of the atomic radius…

A: For the solution refer below images.

Q: Suppose that the coordinate frame 0₁x₁₁Z₁ is obtained from the coordinate frame ooxoyoZo by a…

A: The solution uses the formula for the rotation matrix about the x-axis, which is a special case of…

Q: Why does Qc = -hA(deltaT) and not just hA(deltaT)?

A: There are two expressions for the heat to be condensed.The difference between the two expressions…

Q: The container truck engine operated on the diesel cycle with a compression ratio of 12. Assume the…

A: The diesel cycle is The initial pressure is The initial temperature is The heat removed during…

Q: Q4). Sketch the [112 2 ] plane in the outline of the hexagonal lattice below

A: It is asked to draw plane in hexagonal lattice

Q: Water flows from the nozzle attached to the spray tank shown in the figure below. Determine the…

A: Given:

Q: 3.21 Some animals have learned to take advantage of the Bernoulli effect without having read a fluid…

Q: For the position-time graph shown, pick the corresponding velocity-time graph. Velocity Position…

A: We know thehe derivative of position with respect to ime gives us the velocity.

Q: • Explain turbo-charged and super-charged engine in comparison to naturally-aspirated engine. •…

A: The objective of this question is to understand the differences between naturally-aspirated,…

Q: F6-8. Determine the force in members LK, KC, and CD of the Pratt truss. State if the members are in…

Q: 3. A vibrating mass-spring system exhibits an acceleration amplitude of 27 mm/s2 and a dis-…

A: The acceleration amplitude or maximum acceleration:The displacement amplitude or maximum…

Q: Part D- The Forces in the Members at Joint D Having found Fcp in the analysis of joint C, there are…

A: Ans Given Now draw the FBD of the point B asNow take equilibrium in vertical direction as Hence, the…

Q: A pool ball is shot against the wall of the pool table. Find the velocity and angle of the ball…

Q: Consider the system shown in Fig. P1-77. If a change of 0.7 kPa in the pressure of air causes the…

A: To finddetermine the ratio of..Giventhe specific gravity of mercury, S.G. = 13.56The specific…

Q: 2. Given a closed container of volume 1 L containing 50 g of helium gas, calculate the following: a.…

A: “Since you have posted a question with multiple sub-parts, we will provide the solution only to the…

Q: 4. A pair of connected pulleys receive a force F = 75 N and P = 150 N as depicted in the image. The…

Q: The diagram shows a conical section fabricated from pure aluminum. It is of circular cross section…

A: The temperature at is The temperature at is The diameter is , The lateral surface are insulated

Q: 2. If the engine operates at 50 cycles per second, the power output is A) 381 W B) 45.8 W C) 1145 W…

A: Definition:Engine powerThis engine power focuses on how much labor or energy an engine can generate…

Q: 2- the rubber blocks shown in Figure 2 are used in a double U shear mount component. The dimensions…

A: Given:The dimensions of the rubber block are The value of the applied load, The deflection in the…

Q: The figure 1 above presents a crudely simplified centralised water heating system. The system…

Q: Part B - Average normal strain in cable S Determine the average normal strain in cable S due to…

A: The objective of the question is to calculate the average normal strain in cable S due to the load…

Q: 15. Suppose that we have a product that we want to assemble on a product layout system. The job…

A: Find the given details below:

Q: Calculate the equilibrium temperature of the plate, based on the incoming solar radiation and the…

A: DefinitionThermal radiation:This topic investigates how electromagnetic waves transmit heat across…

Q: 3.51 WP Referring to Fig. P3.51, water contained in a piston-cylinder assembly, initially at 1.5 bar…

A: The initial pressure is The initial quality is The final state is saturated vapour

Q: n the pressure vessel experiment, the readings (µε) in the strain gauges #1, #2 and #6 are 213, -76…

Q: A railway line is laid so that there is no stress in the rails at 8°C. The rails are 30 m long. Take…

Q: 1-D, steady-state conduction with uniform internal energy generation occurs in a plane wall with a…

A: From energy balance, rate of heat generation per unit area is equal to heat transfer by convection…

Q: Problem 4-17: The pipe is stuck in the ground so that when it is pulled upward the frictional force…

A: To findDetermine the initial force P required to pull the pipe out and the elongation just before it…

Q: for some reason it is saying that is not correct. I have tried 5.17PkN, 5.17kN, 5.17PKN, and it will…

A: The force P according to the maximum tension (3 KN) is 5.172 KNThe force P according to the maximum…

Q: In a manufacturing process, a transparent film is being bonded to a substrate as shown in the…

A: The temperature of bond surface is .The temperature of air is .The temperature of the substrate at…

Q: We use a 5 meter long cable with linear mass density of 9 kg/m to lift a bucket of water with total…

Q: A part made of Aluminum 6061-T6 has a yield strength = 400 MPa. For each stress state below, draw…

Q: 2-77. The cables attached to the screw eye are subjected to the three forces shown. Express each…

A: Given data:Need to determine the magnitude and direction of the resultant force.

Q: An insulated piston- cylinder contains ammonia at 1000 kPa, 50°C. Ammonia is expanded in a…

Q: Choose a common metal that is solid at 0°C and liquid at 1500°C. a) Look up the following values:…

Q: A vertical bar consists of three prismatic segments AB, BC, CD with cross sectional areas 6000 mm²,…

Q: The length of the cable segment AB is 10 ft (Eigure 1) The angle a = 30° Figure 10 ft ▲ Part A What…

A: The length of AB is .The angle is The weight of crate is

Q: ●Water enters a boiler at 22.000C at atmospheric pressure through a pipe at an average velocity of…

Q: A hollow cylinder with a mass of m= 100 kg and a diameter of d = 1 m is placed on a conveyor belt.…

A: Given : The mass o hollow cylinder is The diameter of cylinder is The accelration of conveyer belt…

Q: A hollow cylinder with a mass of m= 100 kg and a diameter of d = 1 m is placed on a conveyor belt.…

A: Draw FBD

Q: The shelf bracket is subjected to the force F = 281 Newtons at an angle #= 33.6º. Compute the moment…

A: Given:The force applied to the shelf bracket, The angle made by the applied force, with the…

Q: A spring-loaded piston-cylinder device contains 1 kg of carbon dioxide. This system is heated from…

Concept explainers

Conduction and Convection

When energy travels from one object to another it is said to have undergone heat transfer. Heat transfer is nothing but the transfer of thermal energy or internal energy from one thing to another, like e.g., when a vessel with water, kept on top of a burner, heats up because of the flame underneath it.

Question

Let us consider two water columns at different temperatures, one being at 40^oC and the other being at 20^oC. As both the water columns are separated by a glass wall of area 1m by 2m and a thickness of 0.003m. Calculate the amount of heat transfer. (Thermal Conductivity of glass is 1.4 W/mK)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given and required

VIEW

Step 2: Determination of heat transfer

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

⦁ Two water columns are at different ⦁ temperatures, one being at 35oC and the other being at 18oC. The water columns are separated by a glass wall of area 1m by 2m and a thickness of 0.005m. Calculate the amount of heat transfer. (Thermal Conductivity of glass is 1.6 W/mK)
Q2: A: The exterior wall of a single-story office building near Chicago is 3 m high and 15 m long. The wall consists of 100-mm face brick, 40-mm polystyrene insulating board. 150-mm lightweight concrete block, and an interior 16-mm gypsum. The wall contains three single-glass of 3 mm thickness windows 1.5 m high by 2 m long. Calculate the heat loss through the wall at design conditions if the inside temperature is (20 °C). The outside temperature is (-18 "C).
On a winters day the outside temperature of a 15 inch thick concrete wall is -25F, the wall is 16 ft long and 10 ft high. How manu BTU are required to keep the inside of the wall at 75F? Assume walls thermal conductivity is 0.8BTU/h ft F. Show detailed solutions
A water tank is completely filled with liquid water at 40°C. The tank material is such that it can withstand tension caused by a volume expansion of 5 percent. Determine the maximum temperature rise allowed without jeopardizing safety. Assume a volume expansion coefficient value at that of 65 °C. (Just write the numerical answer. Include - if the answer is negative. No need to put the unit.) Properties of saturated water Volume Specific Heat Jkg - K Thermal Conductivity k, Wim- K Prandti Enthalpy Dynamic Viscosity H. kg/m -s Expansion Coefficient Number Density P. kgim Saturation of Pr Temp. T, "C B. 1/K Liquid Pressure Vaporization P, kPa Liquid Vapor hg, k/kg Liquid Vapor Liquid Vapor Liquid Vapor Liquid Vapor 0.0171 1.792 x 103 0.0173 0.922 x 105 13.5 0.934 x 10-5 1.00 -0.068 x 10 3 1.00 1.00 0.01 0.6113 999.8 0.8721 0.0048 0.0068 2501 2490 2478 4217 4205 1854 0.561 0.571 1.519 x 10-3 1.307 x 10-3 0.946 x 10-5 1.138 x 10 3 0.959 x 10-5 1.002 x 10 3 0.973 x 105 999.9 1857 11.2 0.015…
P3. After a particularly cold night, Alice leaves a tub of water outside. You may consider the ground and air to have temperatures of Te = -10°C and Th = 10°C respectively. How thick is the layer of ice that forms at the bottom of the tub of water, after the tub has been left outside for a long time? The tub of water initially has a layer of water of thickness ho 10 cm. You may assume that the ground and air remain at a constant temperature throughout, and that the side lengths of the tub a, b » ho, i.e. the heat conduction is one- dimensional. Density of ice and water are pice = 920 kg/m³ and pw = 1000 kg/m³. Ice and water have thermal conductivities of kice = 2.22 W K-1 m' -1 and kw 0.556 W K-1 m' -1.
all of the How much thermal energy is required to heat at water in a swimming pool by 1°C if the dimensions are 4 ft deep by 20 ft wide by 75 ft long? Report your result in megajoules.
To ensure a tight fit, the aluminum rivet used in airplane construction are made slightly larger than the rivet holes and cooled by dry ice (solid CO2) before being driven. If the diameter of a hole is 0.500 cm, what should be the diameter of a rive at 20 degree Celsius if its diameter is equal that of a hole when the rivet is cooled to -78 degree Celsius, the temperature of dry ice? Assume the coefficient of expansion to remain constant. (Given and solutions)
Please solve only part 3. This is a 3-part question involving heat transfer. Part 1 and 2 are correct, but I need help how to find part 3. Thank you.
(a) The temperature at the surface of the heating rod, T1. (b) If the salt solution temperature is 300 degree Celcius, what is the value of convection heat transfer coefficient, h of the salt solution ? (c) If the heating rod is not covered by metallic cylinder and corresponds to the result of part (a) and (b), how much the rate of energy transfer to the salt solution ? (d) Compare and discuss the difference of heat transfer with and without the matallic cylinder.
The first part of the question has been worked on, where the heat transfer was calculated to be 6.770 kilowatt, but the problem also asks to calculate the temperature of the outer most surface. What is the temperature of the outer most surface?
In 1 paragraph, make a narrative of what you have learned in Heat Transfer
a metal bar is made up of 3.0 cm of aluminum and 5.0 cm of steel. the free end of the aluminum bar is placed in contact with steam at 100 degree Celsius. at the other side, the free end of the steel bar maintained at 0 degree Celsius by placing it in contact with the ice. find the temperature at the point that connect the aluminum and the steal (junction)