Please no hand writing solution Let the pressure gradient in the pipebe 1400 Pa/m and the diameter of the pipe be4.0 mm.Part AWhat is the average speed through this pipe of 20°C motor oil?Express your answer in millimeters per second.ΤΟΠ ΑΣΦUavg 11.4SubmitX Incorrect; Try Again; 5 attempts remainingPart BPrevious Answers Request AnswerVavg 2 =What is the average speed through this pipe of 100°C motor oil?Express your answer in millimeters per second.ΤΕΙ ΑΣΦSubmit?Request Answer?mm/smm/s

Name: Please no hand writing solution Let the pressure gradient in the pipeb
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Please no hand writing solution Let the pressure gradient in the pipebe 1400 Pa/m and the diameter of the pipe be4.0 mm.Part AWhat is the average speed through this pipe of 20°C motor oil?Express your answer in millimeters per second.ΤΟΠ ΑΣΦUavg 11.4

Answered: Let the pressure gradient in the pipe…

Engineering

Mechanical Engineering

Let the pressure gradient in the pipe be 1400 Pa/m and the diameter of the pipe be 4.0 mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 29 Not yet answered Marked out of 2.00 P Flag question Find the head lost due to friction in a pipe of diameter 5 m and length 5000 cm, through which a liquid of density 900 kg/m is flowing at a velocity of 3 m/s. Use Darcy formula and assume the viscosity of the liquid is 400 poise. B. Write your answer here Reynolds number (Re) = coefficient of friction (f)= Head lost due to friction (h,) =
Learning Portal Academic Departments ETC - CIMS - Courses - Reports - e-Services - Moham Select one: O True O False The energy loss due to the change of flowrate of a fluid flow in direction is known as minor loss. Select one: O True O False Determine the time taken by the oil to get collected in a measuring jar of 26 x 10-3 m³. The oil has the specific that has a mean velocity of 9 m/s in a pipe of cross-sectional area 11 x 10-5 m2. Time taken (in s) arch EUROSTARD
A fluid is being pumped through a pipe. The density of fluid is 872 kg/m³. The viscosity is 2.8x102 Pa.s. The velocity in the pipe is 5.9 m/s. If the Reynolds number is 2100. a- What is the pipe cross-sectional area? b- If the pipe cross-sectional area increased 1.5 fold under same Reynold number, density and viscosity, what is the new velocity?
What is the water pressure as it exits into the air? Water flows from the pipe shown in the figure with a speed of 5.0 m/s. (Eigure 1) Express your answer with the appropriate units. μΑ ? N Value Figure Submit Previous Answers Request Answer Оpen X Incorrect; Try Again; 2 attempts remaining 5.0 cm 4.0 m Part B What is the height h of the standing column of water? 10 cm?
Write T as an answer if the statement is true and F as an answer if the statement is wrong. If your answer is F, then correct the statement Example: Q1- Sinop is a southern city located at Anatolia. A typical answer 1- F: Sinop is a northern city located at Anatolia. Question2-1 Thermal hot wire anemometers measure the temperature of the flow, and they are very small devices which do not disturb the flow significantly. Question2-2 Using a Laser Doppler velocimetry, one can measure the velocity information at a cross section instantaneously. Question2-3 An obstruction flow meter can be used to measure the velocity profile around a car in a wind tunnel. Question2-4 The exact value of the discharge parameter of an orifice meter should be supplied by the producer because it has a design based value.
ball is thrown from A. (Figure 1) Figure 96°F Sunny 3 ft 30° R B 4 8 ft 1 of 1 X
valg, (21535mm 1.15 The pressure difference, Ap, across a partial blockage in an artery (called a stenosis) is approximated by the equation μV Ap - K. 4 + K.(A-1) pv² = K₂ A s.r to zogy nish190 32\V as bonb dignol a 3 basiy noft where V is the blood velocity, u the blood viscosity (FL-2T), p the blood density (ML), D the artery diameter, Ao the area of the unobstructed artery, and A, the area of the stenosis. Determine the dimensions of the constants K, and K. Would this equation be valid in any system of units?
QUESTION 14 The venturi meter has water flowing through it. The pressure difference is 6894.6 Pa. The diameter at point 2 is 0.1524 m, and diameter at point 1 is 2 times of point 2. What is volumetric flow rate through this meter? Write your answer only on m/h only. The coefficient of discharge is assumed to be as unity and density of water 1000 kg/m. [2(P - P2)/p]/2 V2 = C, 1- (A / A}) %3D Click Save and Submit to save and submit. Click Save All Answers to save all answers. Save All Ans
In shut off valve experiment, the 3/ 6th of valve position, the discharge is found as of 6 lit/s for the 27mm diameter pipe. Find the velocity and Reynolds number of the flow. Take the viscosity of water as 1.14x10 Ns/m?. (Enter only the value in the box by considering the unit given in bracket. Do not write the unit in the boxes) Velocity of water (unit in mm/s) = Reynold's number
Part A Let the pressure gradient in the pipe be 1400 Pa/m and the diameter of the pipe be 4.0 mm. What is the average speed through this pipe of 20°C motor oil? Express your answer in millimeters per second. ν ΑΣφ ? Vavg 1 = mm/s Submit Request Answer Part B What is the average speed through this pipe of 100° C motor oil? Express your answer in millimeters per second. Hνα ΑΣΦ ? Vavg 2 = mm/s
A fan is used to blow air (density=1.15 kg/m3) in a duct. A pitot tube is placed in the duct as shown. The static pressure in the duct is measured with a wall tap and pressure gage. Use the gage readings to determine the velocity of the air. note: Pitot tube is used to measure the air total pressure. Mind on the head to be calculated if it is already in air. x 103 Pa Ptot tabe 12 x 103 Pa
B1. A water with viscosity 11.4x10-3 poise is flowing through a pipe of diameter 300 mm at the rate of 500 litres per sec. Find the Reynold's Number & the head lost due to friction in the pipe of length 1 km. (Enter only the values by referring the unit given. Also upload the hand written answers in the link provided) The velocity of flow of water (in m/s) is The value of Reynold's Number is The frictional loss in the pipe (in m) is