no hurry .............a very good handwriting with every step to be mentioned to understand the answer easilystep to followgivenrequirementsolutionresultif not followed the above steps , ready for consequencesi want the solution with a very good handwriting lagrange interpolation is to be used to represent the enthalpy of saturated air as a function of thetemperature. the pairs of values to be used as the basis are (9.470,0),(29.34,10), (57.53,20), and (99.96,30).detremine the coefficients and calculate enthalpy

The lagrangian interpolation formulae: f(x)=∑i=0nf(xi)li(x) here, li(x)=∏i=0, j=1nx-xjxi-xj The…

lagrange interpolation is to be used to represent the enthalpy of saturated air as a function of the temperature. the pairs of values to be used as the basis are (9.470,0),(29.34,10), (57.53,20), and (99.96,30). detremine the coefficients and calculate enthalpy

lagrange interpolation is to be used to represent the enthalpy of saturated air as a function of the temperature. the pairs of values to be used as the basis are (9.470,0),(29.34,10), (57.53,20), and (99.96,30). detremine the coefficients and calculate enthalpy

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

determine the saturation mixing ratio and the mixing ratio of each of the following air samples. For the SMR and MR, leave three decimal places (round to the nearest thousandth). The rank the air samples from highest vapor content to lowest (1 is highest and 6 is lowest). Temp: 14C ; SMR: g/kg ; RH: 90% ; MR: g/kg; Rank: Temp: 20C ; SMR: g/kg ; RH: 60% ; MR: g/kg; Rank: Temp: 24C ; SMR: g/kg ; RH: 40% ; MR: g/kg; Rank: Temp: 30C ; SMR: g/kg ; RH: 40% ; MR: g/kg; Rank: Temp: 34C ; SMR: g/kg ; RH: 30% ; MR: g/kg; Rank: Temp: 38C ; SMR: g/kg ; RH: 15% ; MR: g/kg; Rank: Please explain how you got the rank number.
What is the specific enthalpy for steam at 17.5 bar and 443 degrees celcius. Show the steps for double interpolation to arrive at your answer.
A probe with an improvement coefficient of 0.88 will measure the temperature in an ideal gas flow with a speed of 95 m/s. Since the gas constant of the liquid is 0.288 kJ/kgK and its isanthropic base is 1.4, how many ºC is the difference between the temperature that the probe will show and the actual temperature of the liquid? a. 2.317 b. 3.939 c. 2.455 d. 2.716 e. 3.268
2. Two hundred and fifty pounds of a mixture of 10 mol% propane 20% n-butane, and 70% n-pentane is completely vaporized in a pipe still in one hour. At the outlet, the temperature anc 433 F and 600 psia. What is the volumetric flow pressure are rate in cfm at the outlet conditions? Answer: The physical properties of the gas are: Tc Pc MW Propane 369.9 K 665.8 R 42.0 atm 44 Butane 425.17 K 765.31 R 37.47 atm 58 Pentane 469.8 K 845.64 R 33.3 atm 72
A continuous flow calorimeter was used to obtain the calorific value of a sample of fuel and the following data collected: Mass of fuel: 2.25kg Inlet water temp: ll CQuantity of water: 360 L Outlet water temp: 60 CCalorimeter efficiency: 85 % Calculate the calorific value of the sample (kJ/kg).
Q.1: Air of 40 °C DB temperature and 20 °C WB temperature is flowing with rate of 5000 kg/hr. Water at 20 °C is sprayed over the flowing air and because of that, the DB temperature of the air decreases to 26 °C. If the barometric pressure of the air is 90 kPa, calculate: 1. The relative humidity and moisture content before and after the spraying process. 2. The mass flow rate of water evaporated in the air during the spraying process. 3. The amount of heat removed from the air in kW. 4. If the flowing air (after spraying) is passed over a surface of temperature 14 °C, is there any condensation would happen on that surface?
Using the following information, determine the vapor pressure of water at 300 °C. Note: We started this problem in week 6 lecture 3. Please refer to the lecture to get started on this problem. You only need to show your work starting from where the lecture left off. H₂0 at T = 179.88 degrees C the vapor pressure is PSAT = 10 bar. The enthalpy of vaporization is 2014.59 kJ/kg V = 0.1944 m³/kg V¹ = 0.001127 m³/kg The equation we left off on in class was, cpf 1 [P² psat dpsat pi psat Tf 1 ∆vapH (TF 1 RAZ Ti dT T2a
I am trying to find the mass flow rate of cooling water in the condenser Known values T9 = 20 C, T10 = 30 C, m_dot = 20.27 kg/s, h3 = 2190.209 kJ/kg, h4 = 146.681 kJ/kg The formulas I have found require using cp or knowing the enthalpies of states 9 and 10 but I am not sure how to find these. how do I solve this problem.
The concentration of salt ? g/L in homemade soap is given as a function of time as follows: ??/dt = (0.37? − 0.03)? At the initial time, ? = 0 minute, the salt concentration is 20 g/L. Choose a step size in a range of 1 < h ≤ 1.5 minutes for the interval from 0 to 8h minutes and apply THREE (3) numerical methods to compute the salt concentration. Select the best numerical method to estimate the salt concentration and justify your answer. method 1: ruler's method
Hi, pleass help me solve this problem. I need it asap. Thank you so much. *** A thermometer in a 10 x 8 x 4 m room reads 25°C and a humidistat reads the R. H. to be 33%. What mas of water vapor is in the room? Saturated air at 25°C contains 19.33 g h2O/m^3.
8. The exact differential equation of enthalpy can be expressed as below: dH=-uCpdp + C₂dT where C: constant pressure heat capacity u: Joule-Thomson coefficient μl= a) Derive the exact differential equation of enthalpy from the general exact differential equation of enthalpy: = (3), dp + (7) dr T dH = b) Considering that you use nitrogen gas to make a temperature drop to an isenthalpic system, how much pressure drop is required to cool the system by 20 K? The Joule-Thomson coefficient of nitrogen is u 3 0.27 K atm¹. c) Prove that the Joule-Thomson expansion can occur without change of enthalpy (isenthalpic process).
Q3) The temperature of the vehicle cabin is 72F and Ø = 50%. pR (i) the partial pressure of the air and water vapor (ii) the vapor density, and (iii) the 29.92 in. Hg Find humidity ratio of the mixture. Ans. (i) 14.496 psi , 0.1941 psi, (ii) 0.000613 Ib/ft3, (iii) 0.00833