K 5' El constant 10 ft 5' 10 k-ft 10 ft 10 k-ft

Q: Stresses acting on an infinitesimal soil element are shown in the figure (with o₂ > 0). The major…

A: Given  Compressive stresses are taken with positive sign .

Q: *A 40-lb, 0.8-ft-diameter, 1-ft-tall cylindrical tank slides slowly down a ramp with a constant…

A:

Q: 1 of 5 | Railway Engineering Save For a sleeper density of (n + 5), the number of sleepers required…

A: Given data: Sleeper density = n+5 Length of rail = 12.8 (general value)                      n=13…

Q: 2) Using angles to the right shown below, calculate the forward and back bearings and azimuths of…

A:

Q: Calculate the true reduced level (m) of a point A after correcting the refraction and curvature. The…

A: Given- distance d=2 km,staff reading fore sight F.S=2.56 m,bench mark BM=100 m,back sight BS=1.34 m.…

Q: 2) Using angles to the right shown below, calculate the forward and back bearings and azimuths of…

A:

Q: P10-28. The shaft carries a torque of 4500 N-m between sections B and C. Compute the maximum shear…

A: Diameter of shaft =25mm Torque applied (T)= 4500N-m T=4.5kN-m To find maximum shear stress near B

Q: The perception reaction time for a vehicle travelling at 90 km/h, given the coefficient of…

A: Given data: SSD=170 mv=90 kmhrg=9.81 ms2f=0.35

Q: (Situation 2) Determine the support reactions and member forces on the following trusses: 9 ft ₁2 k…

A: Given figure shows a truss provided with hinge support at D and roller support at B Required-To…

Q: Two identical pipes (i.e. having the sam same diameter, and same roughness) o withdraw water from a…

A: To find ratio of discharge in parallel connection to that in series connection

Q: Question 2 The figure below shows a three-layer system. Calculate the maximum horizontal strain at…

A:

Q: From the following measured interiror angles of a five sided figure, compute the following: Station…

A:

Q: Q-6 While designing for a steel column of Fe250 grade the base plate resting on a concrete pedestal…

A: Given data: While designing of Fe250 grade. The base plate resting on a concrete pedestal of M20…

Q: Four balls of equal radii form a pyramid supported by a smooth horizontal plane surface. The three…

A: Solution:-The given data are as follows,There are four equal-sized balls.  Assume that the radius of…

Q: Fluid is being given to a patient by an IV in a vein of their arm. The fluid is a saline solution…

A:

Q: Exercise 1.4.2 A gentle hill slope with an area of 10 ^ 4 * m ^ 2 receives rain for a period of 40…

A: Given data:- The given average rainfall intensity, =30 mm/hr The given area of hill is, =104 m2 The…

Q: Differentiate Infiltration, Percolation and Seepage.

A: Seepage:- The flow of water in soils is a serious and common issue with building foundations in…

Q: Two identical pipes (i.e. having the same length, same diameter, and same roughness) are used to…

A:

Q: The table below show 4hr U.H. drive 12hr U.H by using S-Curve? Time (hr) 04 8 12 16 20 24 28 32 36…

A: Given A 4 HR unit hydrograph ordinates Required 12 HR unit hydrograph using s curve method

Q: 3 kN T 2m 2 m LA G -3 m- B OKI -3 m- -1.5 m (b) *Assume A to be hinged and D to be roller. -3 m- 3…

A: Support Reaction  The roller support provides only one degree of restraint in the vertical…

Q: 1)Determine the horizontal and vertical components of the deflection at joint B B 4. 4m 3m C 84 kN A…

A: Given data  A = 1200 mm2  E = 200 GPA  Find horizontal and vertical deflection of joint B.

Q: a soil having a void ratio of 0.50 has a specific gravity of 2.70. compute the effective unit weight…

A: Answer  Quick sand is a phenomenon when the upward seepage pressure becomes equal to submerged…

Q: -) A (50 cm) well fully penetrates an unconfined aquifer of saturated depth 80 m. When a discharge…

A:

Q: 5.47 (Ans. max V = 67.5 ft-k, max M = -675 ft-k) 15 ft- 3 klf Hinge 105 OS 15 ft15 ft- 12 ft TER

A: Objective: To write the shear and bending moment equations for the given beam and determine the…

Q: 4-One body's reaction to the other occurs perpendicular to the contact surface when the two --bodies…

A: We have to asked Science of Statics Questions and we have Explain the Question with Fill in the…

Q: Determine the slope length (L) between two points given the following information: Horizontal…

A:

Q: Problem 3: A sailor is being rescued using a boatswain's chair that is suspended from a pulley that…

A:

Q: Problem 2. A base line is measured and subsequent calculations show that its total length is…

A:

Q: (d) 1 kip/ft find moment at A, and reaction and find Ay find reaction at B find Dy and Dx

A:

Q: Four balls of equal radii form a pyramid supported by a smooth horizontal plane surface. The three…

A: Solution:-The given data are as follows,There are four equal-sized balls.  Assume that the radius of…

Q: 2., The forces F1, F2, and F3 act as shown. Find the x, y, and z components of each force, and the…

A: Objective: To determine the x, y and z components of the given forces and calculate the resultant…

Q: E A Dn. C JI D

A:

Q: 1. A sample of saturated soil weighs 588N and has a volume of 0.03m3. If the void ratio of the soil…

A:

Q: Determine the member of forces of the truss. Utilize Method of joints and Method of section Put if…

A: To find force in all members of the truss

Q: A group of 16 piles of 50 cm diameter in arranged with a centry to centre sporing of 1.0 m. The…

A: The ultimate bearing capacity of a pile is the maximum load which it can carry without failure or…

Q: A long natural slope in overconsolidated fissured clay of saturated unit weight 22 kN/m³, is…

A: Given data- γsaturated=22 kN/m3,i=14o,depth z=4 m,ϕ=20o. To Find- The factor of safety FOS.

Q: : Determine the amount of deflection at free also the maximum deflection. Use W = 35 kN/m, M = 15…

A:

Q: Determine the absolute weight and the weight relative to the rotating earth of a 87-kg man if he is…

A: From Given  Data :  Mass of man ( m ) = 87 kg latitude ( γ ) = 33°   To Find :   Absolute weight…

Q: Given the following properties of beam: b=250mm, d=325mm and h=400mm a. Assuming the concrete is…

A: Given : b = 250 mm , d = 325 mm and  h = 400 mm Uncracked moment = 25 KN -m 4 - 16 bars To find : 1.…

Q: For a sample of water with the ionic composition shown below, the Carbonate and Non-carbonate…

A: Equivalent weight=( total weight) / valency Eq wt of CaCO3 = 100/2 = 50mg/l To find carbonate…

Q: #2 Draw the influence lines for (a) the vertical reaction at A, (b) the shear at C, and (c) the…

A:

Q: Given: ● . • Find: A (1030.00 N, 990.00 E), B (1040.00 N, 1120.00 E) ZA = 51° 54'41", ZB = 53°…

A:

Q: -2 m- -2 m- B 2m 2m 2 kN

A:

Q: Question-An isolated three-phase traffic signal is designed by webster's method. The critical flow…

A: To find out the optimal signal cycle length by Webster method.

Q: 3-In mechanics, natural quantities are expressed in terms of three basic quantities approved in the…

A: Engineering mechanics is the discipline devoted to the solution of mechanics problems through the…

Q: 2-21. Determine the reactions at the supports A and B of the compound beam. There is a pin at C. 4KN…

A:

Q: A set of sandstones plugs from the Vicksburg formation in South Texas gave the following results…

A:

Q: Question-An isolated three-phase traffic signal is designed by webster's method. The critical flow…

A:

Q: A moist soil has a unit weight of 125pcf. Given the specific gravity of solids = 2.67 and the…

A:

Q: A concentrically loaded isolated square footing of size 2 m x 2 m carries a concentrated vertical…

A:

Dependence on mechanical properties

The mechanical properties of materials are those structures that include the reaction to the load used. Metal switching features determine the scope of the usefulness of the content and establish the expected service life. Machine structures are also used to help distinguish and identify material objects. The most common mechanical properties considered are strength, ductility, stiffness, impact resistance, and resilience to fractures.