QUESTION 6: Consider the circuit of Figure P11.3 with transistor parameters ß= 155 , V4=0, and VBE(on) =0.66 V. The circuit is biased by V*= 6 V and V = -6 V.Design the circuit such that the Q-point values are Icı = Ic2 = 140 µA, and vo1 =vo2 = 1.2 V for vị = v2 = 0.Format : 98.34Rc (kN)Format : 47.93RE (kN)IciRCRCv0210aREFigure P11.3

Answered: Image /qna-images/answer/bf56be08-0afe-452d-ac0b-37f5b2c42f92.jpg

JESTION 6: Consider the circuit of Figure P11.3 with transistor parameters ß = 155 , V4=∞, and V3BE(on) = 56 V. The circuit is biased by V*= 6 V and V = -6 V. sign the circuit such that the Q-point values are Icı =Ic2= 140 µA, and vo1 = vo2 = 1.2 V for vị = v2 = 0. Format : 98.34 Format : 47.93 - (ΚΩ) = (kN) レメ RC RC vo2 10a Q2 RE Figure P11.3

JESTION 6: Consider the circuit of Figure P11.3 with transistor parameters ß = 155 , V4=∞, and V3BE(on) = 56 V. The circuit is biased by V*= 6 V and V = -6 V. sign the circuit such that the Q-point values are Icı =Ic2= 140 µA, and vo1 = vo2 = 1.2 V for vị = v2 = 0. Format : 98.34 Format : 47.93 - (ΚΩ) = (kN) レメ RC RC vo2 10a Q2 RE Figure P11.3

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Set up a midpoint bias for a JFET with IDSS = 14 mA and VGS(off) = -10 V. Use a 24 V dc source as the supply voltage. Show the circuit and resistor values. Indicate the value of ID. Indicate the value of VGS. Indicate the value of VDS.
Identify the source, drain, gate, and bulk terminalsand find the current I in the transistorsAssume VTN = 0.70 V
........ (Figure-1) R. RB= 380kN,Rc= 1kN B = 100, VBB = Vcc=12V RB ww Vec CC ......... I, V CE СЕ V ВЕ BB Q-1-b) Describe briefly the input / output characteristics and application of Common Emitter BJT Configuration
Determine VB, VE, VC, VCE, IB, IE, and IC in Figure. The 2N3904 is a general purpose transistor with a typical BDC 200 Vcc +30 V WWII VCE VB R₁ • 22 ΚΩ IC(mA) Chọn... * Chọn... * IB(UA) Chọn... * IE(MA) Chọn... ◆ Chọn... * Chọn... * Chọn... * VE VC R₂ ´ 10 ΚΩ www Rc 1.0 ΚΩ 2N3904 PDC=200 RE 1.0 ΚΩ
Q1:- find the emitter, base and collector currents and VE. (let any parameters if you need). + Vcc=6 V 2 k2 530 k2
Part of the data sheet of the 2N5457 model JFET transistor is provided in your question paper. Answer the following using this data sheet i. Find the Ip (drain current) value for VGs = 0 V. (VGs (off) = - 3.5V) ii. Find the Ip (drain current) value for VGs = -2 V. (VGs (ofM= - 3.5V) iii. Calculate the values of Vps and VGs in the circuit given in the figure. Use the minimum values given in the data sheet. VDD +12 V Rp 10 kf 2N5457 Rs 5.6 kf
1. Design a fixed-base BJT bias circuit, similar to the one shown in Figure 1, such that VCE = 5.5 V. Assume VBE (on) = 0.7 V and 3=150 for the transistor. 5V HUF RB ww Figure 1 1.5k Q2N2222 12V Note: Use PN2222A in Multisim
Figure 1 shows the typical output characteristics of MOSFET. Those characteristics show the difference curve of the drain current, Ip, as function of the drain- source voltage, VDs at a given gate-source voltage, VGs. In the Figure 1, it shows that the Ohmic region. What the meaning of the Ohmic region? Explain with necessary example any consequences that will happen for any condition of MOSFET. 360 10 V ev 7V 320 280 Ohmic region + 240 200 160 120 5.5 V- 80 40 2 3 Vos [V] Figure 1 lo [A]
Draw and explain the schematic diagram for the following: Common Base NPN operating in cut-off region Common Emitter PNP operating in the active region Common Collector NPN operating saturation region From the given figure, identify and explain the 1.Type of Transistor 2. Type of Configuration 3. Mode of Operation V3 SV Q2 100A/A Q3 100A/A 7 V4 5V V6 5V
Subject:Electronics Engineering What is pinch off voltage in JFET? Define pinch off voltage with respect to different characteristics of an n-channel JFET. Is the drain current affected by VP? Justify your answer.
From the figure shown, when S1 is at 1 : up position; the following statement is not correct except: (a) Collector-emitter voltage of Q1 is approximately zero (b) the LED will illuminate (c) the base voltage of Q2 is equal to 9 V (d) (b) and (c)
04:- Design a bias circuit for NPN silicon transistor having a nominal B-100 to be used in voltage divider circuit with Q-point of Ic 10 mA and VCE = 10 V. Use standard valued 5% resistors and draw a schematic diagram of your design. (10 points)