Item A is one of the products manufactured at ABC Manufacturing. • Each order for producing the product has a cost of $300/order, regardless of the number of units ordered. • The lead time for placing the order is 2 week(s). • The inventory cost is $3/ unit/week and the on-hand inventory at the beginning of week 1 is 145 units. The gross requirement for Item A is specified for the beginning of weeks 1 through 8 in the table that follows. Item A Week 1 Week 2 Week 3 Week 4 Week 5 Week 6 Week 7 Week 8 60 65 0 90 0 55 95 85 Gross Requirement On-hand Inventory Net Requirement Planned Order Receipt Planned Order Release For a "lot size using Part Period" scheduling policy, determine the total cost for the 8 week period. Assume that inventory is tracked at the beginning of the period. The number of units ordered can be a multiple of the Part Period, depending on the computed net requirement in a week. What is total number of units held in inventory during the planning period (i.e. weeks 1 through 8)?

Item A is one of the products manufactured at ABC Manufacturing. • Each order for producing the product has a cost of $300/order, regardless of the number of units ordered. • The lead time for placing the order is 2 week(s). • The inventory cost is $3/ unit/week and the on-hand inventory at the beginning of week 1 is 145 units. The gross requirement for Item A is specified for the beginning of weeks 1 through 8 in the table that follows. Item A Week 1 Week 2 Week 3 Week 4 Week 5 Week 6 Week 7 Week 8 60 65 0 90 0 55 95 85 Gross Requirement On-hand Inventory Net Requirement Planned Order Receipt Planned Order Release For a "lot size using Part Period" scheduling policy, determine the total cost for the 8 week period. Assume that inventory is tracked at the beginning of the period. The number of units ordered can be a multiple of the Part Period, depending on the computed net requirement in a week. What is total number of units held in inventory during the planning period (i.e. weeks 1 through 8)?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A specialty coffeehouse sells Colombian coffee at a fair rate of 300 kilograms annually. the beans are purchased from a local supplier for $3 per kilogram. the coffeehouse estimates that it costs $50 in paperwork and labor to place an order for the coffee, and holding costs are based on a 10 percent annual interest rate. a. determine the optimal order quantity for Coffee? b. what is the time between the placement of orders? C. what is the average optimal annual cost? d. Suppose the coffee is ordered in a box of 50kg each. how many boxes should the coffee shop order? A- B. 問

The BOM for product A is shown in Figure 11.40, and datafrom the inventory records are shown in Table 11.9. In theMPS for product A, the MPS start row has 100 units in week 3and 200 in week 6. Develop the material requirements planfor the next 6 weeks for items C, D, and E.a. Develop the material requirements plan for the next6 weeks for items C, D, and E.b. What specific managerial actions are required inweek 1?
TWM Company purchases 8000 units of product each year at a unit cost of $10.00. The order cost is $30.00 per order, and the holding cost per unit per year is $3.00. a) What are the economic order quantity, the total annual cost, the number of orders to place in one year, and the reorder point when the lead time is two weeks? b) What happens to the EOQ if backordering is possible and the stockout cost per unit per year is $1.00? c) The supplier is offering a special discount and has temporarily reduced his unit price from $10.00 to $9.00. What amount should be purchased to take advantage of the discount? d) The supplier will increase his unit price from $10.00 to $11.00 on 1 January. What amount should be purchased and delivered on 31 December before the price increase is effective if the stock position is 346 units? What will be the cost saving of the special purchase
A chemical firm produces sodium bisulfate in 100-pound bags. Demand for this product is 20 tonsper day. The capacity for producing the product is 50 tons per day. Setup costs $100, and storage andhandling costs are $5 per ton a year. The firm operates 200 days a year. (Note: 1 ton = 2,000 pounds.)a. How many bags per run are optimal?b. What would the average inventory be for this lot size?c. Determine the approximate length of a production run, in days.d. About how many runs per year would there be?e. How much could the company save annually if the setup cost could be reduced to $25 per run?
1) A product is made- to- stock. annual demand is 60,000 units. each unit costs $4 and the annual holding cost rate = 25%. setup cost to produce this product is $300. Determine 1-Economic order quantity 2-Total inventory costs for this situation
Assume three products are made in four departments A, B, C, and D. Product 1 has a production volume of 20 pallets per week in the sequence ABCDB. Product 2 has 10 pallets per week in sequence ACDB. Product3 and 4 pallets per week in sequence BD. 1. Construct From-To chart indicating the number of trips from one department to another. 2. Construct relationship chart following these rules: “A" for any two departments with a total number of trips ( including both directions) greater than 30; “E" for greater than 20 but less than or equal to 30; “I" for greater than 10 but less than or equal to 20;"O" for greater than 5 but less than or equal to 10; and “U' for greater than or equal to zero but less than or equal to 5. Show all your computations
An order for 100 of a product is processed on work centers A and B. The setup time on A is 30 minutes, and run time is 10 minutes per piece. The setup time on B is 50 minutes, and the run time is 5 minutes per piece. Wait time between the two operations is 4 hours. The move time between A and B is 10 minutes. Wait time after operation B is 4 hours, and the move time into stores is 15 minutes. There is no queue at either workstation. If it is decided to overlap operations A and B by splitting the lot of 100 into two lots of 70 and 30. Wait time between A and B and between B and stores is eliminated. Setup on operation B can start before the first batch arrives. Calculate the manufacturing lead time for the whole order. Calculate the manufacturing lead time for the first patch.
1. DREZ Inc. has three departments, each of which houses variety of manufacturing equipment. One department has six machines listed in the table. Note: Add 10 feet each side of the first two machines types and 8 feet to the others to allow for operators access, material handling carrier access and work-in process storage. Machine Typе Length(ft) Width(ft) No. of machines Hobbing 10 1 Punch Press 10 10 1 Extruding Equipment Injection Molding Surface Finishing 20 10 2 10 10 3. 5 5 4 Debburing 10 10 Compute the total space requirement of the cell considering the following assumptions for each equipment type: a. Auxiliary space requirement is 10% of those machine area b. Operator space is 8% of the required of the auxiliary and machine space С. Material storage is 20% of the actual area required for machines d. Additional allowance is 80% of the areas determined in a,b.c and machine area.
1.Convert 21 inches of Hg (vacuum, gauge) to kPa (absolute) 2. Trays which hold 10 ounces are being processed in a continuous retort. The cook zone of the retort is 120 inches long. The belt speed is 2.1 feet per minute. If the trays are 5 inches wide and spaced 1 inch apart on the belt, what is the production rate of the system in trays per hour? What is the production rate in kg per hour? What is the exposure time of a tray in the cooking zone in minutes? 3. A differential pressure sensor is attached across the two effects in an evaporator reads 5.6 psi with the high side attached to the first effect. A separate gauge on the first effect reads 9.21 inches Hg (vacuum). What are the pressures of the first and second effects in kPa absolute?
A certain job shop specializes in one-of-a-kind orders dealing with parts of medium-to-high complexity. A typical part is processed sequentially through ten machines in batch sizes of one. The shop contains a total of eight conventional machine tools and operates 40 hours per week of production time. Average time values on each part per machine are: Machining time = 0.5 hour; Work handling time = 0.3 hour; Tool change time = 0.2 hour; Setup time = 3 hours; Nonoperation time = 12 hours. A new programmable machine is being considered that can perform all ten operations in a single setup. The programming of the machine for this part will require 20 hours; however, the programming can be done off-line, without tying up the machine. Setup time will be just 2 hours because simpler fixtures will be used. Total machining time will be reduced to 80% of its previous value due to advanced tool control algorithms; work handling time will be the same as for one machine; and total tool change time…
1. A certain batch of parts is routed through six machines in a batch production plant. The setup and operation times for each machine are given in the table below. Batch size is 200 and the average nonoperation time per machine is15 hr. Determine (a) manufacturing lead time and (b) hourly production rate for operation 4.Machine 1 2 3 4 5 6Setup time (hr) 5 3 6 4 5 3Operation time (min) 3.0 3.3 8.2 3.9 4.5 2.3 a. 6(4.3+200(3.9/60)+15) = 193.8 hours 24.2 days if 8 hour shiftb. 4(60)+200(3.9)/200 =5.1 hourly production for operation 4 2. Suppose the part in the previous problem is made in very large quantities on a production line in which an automated work handling system is used to transfer parts between machines. Transfer time between stations is 30 sec. total time required to setup the entire line is 102 hr. Assume that the operation times at the individual machines remain the same as in the previous problem, Determine (a) manufacturing lead time for a part coming off the line,…
A product line has two models: X and Y. Model X consists of 4 components: a, b, c, and d. The number of processing operations required to produce these four components are 2, 3, 4, and 5, respectively. Model Y consists of 3 components: e, f, and g. The number of pro-cessing operations required to produce these three components are, 6, 7, and 8 respectively.The annual quantity of Model X is 1,000 units and of Model Y is 1,500 units. Determine the total number of components and processing operations associated with these two models.