Answered: IR Rs IL もI V2 = 12v VL = 12V V; =16V…

IR Rs IL もI V2 = 12v VL = 12V V; =16V a) Find the Rs and RL values that will keep VL constont at 12 Volts if the load current I, varies between 0-200 mA. b) Calculate the power of the Zener diode.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 4RQ: What is the difference between a diode and rectifier?

See similar textbooks

Related questions

Q: An experimental ac Voltmeter uses the following circuit , where the PMMC movement has Rm = 100 Q and…

A: PMMC A permanent magnet moving coil is an instrument to measure dc quantity across the target…

Q: Consider the circuit below consisting of diode-connected NMOS transistors. Assume K' = 100 µA / V2…

Q: Consider an NMOS structure that is made with the following characteristics tox = 100 A, N, = 8×10“…

A: NOTE-As per the rules we can answer only 3 sub-parts, please post the remaining sub-parts as the…

Q: An NMOStransistor is to be used as a power switchto disable one core of a multicore processor…

A: The resistance of the core is calculated as shown below: The core resistance is also given by the…

Q: Q22 A transistor circuit is given below. The Zener diode breakdown voltage is 5.3 V as shown. Take…

A: Given transistor circuit is - Given that zener diode is in breakdown region and breakdown voltage…

Q: A) A rectifiers shown in fig.3. If the output current assumed to be ripple free. (a) Draw the output…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: 4.3 PMOS Transistors 4.47. Calculate K, for a PMOS transistor with u, 200 cm2/V · s for an oxide…

A: For a PMOS transistor, Hole mobility μp=200cm2/V-s Find Kp' for an oxide thickness of, (a) 50nm (b)…

Q: Q4: An AC voltmeter uses the circuit below. The meter has an internal resistance of 1000 and…

Q: A PV system is to be designed using 220-V (DC-AC) inverter with efficiency of 90% and a bank of…

A: This question is from "Power Electronics". Under which we are going to study about the "inverters".

Q: Assume you are to create n*pn transistor using n- and p-typed doped silicon w the following doping…

Q: Suppose that a certain npn transistor has VBE=0.7 V for IE = 10 mA. Compute VBE for IE = 1 mA.…

A: Given:

Q: An intrinsic semiconductor is neither a good conductor nor a good insulator. Select one: True O…

Q: Consider an npn transistor with vE =0.7 V at i =1 mA. Find vRE at i =0.1 mA. %3D %3D

A: Given that VBE1=0.7Vic1=1mAVBE2=?ic2=0.1mA

Q: 1. Using an Example LED computation, What Value series resistor should be used to produce 21mA of…

Q: The destructive breakdown of silicon dioxide occurs with an electric field of about 10 million V/cm.…

A: 1- The breakdown voltage for the given electric for the MOSFET is calculated as shown below:…

Q: You are tasked to design a dc power supply that operates from a single-phase ac supply (50Hz) with…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: Assume you are to create n+pn transistor using n- and p-typed doped silicon with the following…

A: n=3 1018 /cm3, p=6.2/cm3, and n=5 1016/cm3

Q: A battery of em.f 4V and prternal. xesistance 2.n is joined to a desistor of 82 calculate the…

A: Given, A battery of EMF 4 V and internal resistance 2 Ω is joined to a resistor 8 Ω,

Q: 1. A circuit with 2 or more connected transistors is called _________ or multi-staged amplification.…

Q: Given a current mirror circuit using NMOS with Vth = IV, Kn(W/L)=0.25e-3 a. If1=1.5mA, find R1=? b.…

A: A current mirror is a circuit created to manage the current flowing through another active device in…

Q: In the Zener regulator shown, the Zener diode has the parameters V = 5.2 V, r, = 20 Q, 1, =0.5 mA 20

A: A Zener diode has a low Reverse breakdown voltage and gives a constant output voltage when operated…

Q: 8.3 A single-phase diode-clamped inverter has m = 5. Find (a) instantaneous, average, and rms…

A: Solution : Calculate the number of separate dc sequences N N = m-1Calculate the maximum output…

Q: 2) An NMOS device of gate dielectric (k=10.2) thickness 53nm and W/L ratio of 1 biased at Vd=0.07v…

Q: 3.7 (a) If an nMOS process has fox = 25 nm, find N so that y = 0.5 V1/2 (b) If tox is doubled, what…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: Assume you are to create n+pn transistor using n- and p-typed doped silicon with the following…

A: n=3 1018 /cm3 p=6.8/cm3 and n=5 1016/cm3,

Q: NMOS Operating Region? Determine the Values of Rp and Rs such that the circuit below operates at I,…

Q: a- Analyze the DTL circuit shown. Assume VBE (sat) =0.8 V, VCE (sat) = 0.2 V, and the drop across a…

A: The given circuit is as shown below :

Q: I-V Characteristics For a NMOS, sketch a I, vs. V ps plot. Label all regions and conditions…

Q: Consider the transistor inverter on the right driving a dc motor modelled as a 1.2mH inductor. The…

A: Let us first understand Transistor Inverter - A transistor is a device that functions as a switch…

Q: Plot the power-delay product versus power for thelogic gate with the power-delay characteristic…

A: Given: To plot the power-delay product versus power for the logic gate with the power-delay…

Q: It is desired to form a 0.2 um-deep source-drain diffusion for a transistor using a…

A: 1. Source drain diffusion transistor - The source/channel regions of a MOSFET are, as an outcome,…

Q: a- Analyze the DTL circuit shown. Assume VBE (sat) =0.8 V, VCE (sat) = 0.2 V, and the drop across a…

A: DTL circuit; VBE(sat)=0.8V VCE(sat)=0.2V drop across the conducting diode=0.7 V β=25

Q: The specific name for the AC-to-DC converter is: А. DC Chopper В. Rectifier С. Inverter D.…

A: 1) To connect AC to DC we use rectifier. Ans. Rectifier.

Q: *43. a. Design the network of Fig. 2.187 to maintain Vį at 12 V for a load variation (I,) from 0 mA…

A: Given: VL=12VLoad variation(IL)=0mA to 200mA

Q: e tasked to design a dc power supply that operates from a single-phase ac supply (50Hz) with source…

Q: Q1/ For the circuit shown in fig (1), the silicon diode devices used VBE sat=0.8volt, VCE sat= 0.2…

A: the fan out of the above-given circuit is determined as shown below

Q: *43. a. Design the network of Fig. 2.187 to maintain V1 at 12 V for a load variation (I,) from 0mA…

Q: Ехample a power plant of 2 MW, in which a large number of PV modules are connected in series. The 2…

A: Solar Photovoltaic Array Photovoltaic Array is formed by connecting an N-number of PV modules in…

Q: 3300 Si 平本Ge +5V

Q: Q1: For the circuit shown below, assuming V, = 10V: 1. Calculate the current in the diode (Ip). 1 k2…

Q: A single-phase diode-clamped inverter has m = 5. Find (a) instantaneous, average, and rms currents…

A: A) The number of separate dc sequences N N = m−1N = 5−1N=4The maximum output voltage value : Vo max…

Q: direct current in our transmission lines

A: DC and AC current- Current that which changes its direction frequently is called alternating current…

Q: If you employ constant field scaling between different MOSFET generations, by what factor does the…

A: We need to select correct option for given statement

Q: Vp Vr = 0.7 V - Ideal diode- Ip Draw the Volt-ampere characteristic curve of the device and explain.…

A: A voltage -ampere characteristics of are voltage to the current curve drawn with the variation of…

Q: 2.) Draw the transistor level implementation of the following function: f= (A+B)CD Annotate sizes on…

Q: For a single-phase single-pulse thyristor rectifier with resistive load (R=15 Ohms) shown in Fig.…

Q: Rizlosz Egalov TR, = 3052 Is= 2A considered' ieteal, using first model of approximation , diodes the…

Q: Explain in details the PCM system,with example

Question

IR
Rs
I年
IL
V3 = 12v
VL =12V
V; =16V
a) Find the Rs and RL values that will keep VL constont
at 12 Volts if the load current I, varies between 0-200 mA.
b) Calculate the power of the Zener diode.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is the difference between a diode and rectifier?
Determine the peak output voltage for the bridge rectifier in this figure. Assuming the practical model, what PIV rating is required for the diode? The transformer is specified to have a 12 Vrms secondary voltage for the standard 110 V across the primary. D3 110 V Vpisec) RL 10 kN- Vploun) alll loll
Draw a full wave bridge rectifier circuit with input voltage is vz = 18 sin(1100t), design the filter circuit for 0.25 V ripple voltage. Assume that the load resistance of the circuit is RL = 500 N and the each diode parameters are V, = 0.7 V and rf = 0 N %3D respectively.
Half-wave diode rectifier AC voltmeter circuit with values Rd = 20Q, Rsh = 200Q, direct bias current D1 = 200uA, Im = 100uA and Rm = 2009. The Vrms measurement range is from O to 20V. What is the value of Rs used?, 01 R. In Rh R O a. 22.44 k ? O b. 33.66 kQ c. 44.88 KQ d. 67 kQ
Consider the circuit shown in the figure below with Ry=13 ko and R=9 kO. The Zener diode voltage is Vz = 3.5 V, then the currents Iz and , respectively, are equal to: R1 ww 20 V O a. 1.280 mA, 0.789 mA O b. 0.680 mA, 0.189 mA O c. 0.880 mA 0.389 mA O d. 1.080 mA, 0.589 mA
2. Design a full wave rectifier for a regulator that delivers 100W electrical power to a white off-the-shelf LED. Per datasheet, the LED requires 33V and draws 3A current. You are required to limit the ripple voltage to less than 20% of average DC voltage of the output. Assume all diodes have Von=0.7V and negligible off current.a. Draw the circuit diagram.b. Determine the voltage of transformer and capacitance of the filter
E = 20V, R = 220 ohm, Vz = 10 V, Pzmax =400 mW Calculate; a.) RL that will establish maximum power conditions for the Zener diode. (in k-ohm) b.) IR in mA c.) IL in mA
A single phase full bridge inverter has RLC load of R=4 ohm, L=35 mH, and C=155 uF. The DC Input voltage is 230 V and the fundamental output frequency is 50 Hz. Calculate the condition time of each diode.
Problem # 4 In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VpC e. PIV (Peak Inverse Voltage) 10:1 Dy 1ISV ms Ouiput RL 2.2 k2 D, 50 pF All diodes are IN4001. alleee
A commercially available IN4002 diode used in power supplies has the following typical data: (VDI, IDI) = (0.6V, 1mA) (VD2, ID2) = (0.8V, 100mA) Find its reverse saturation current Is and ideality factor n.
Determine the ripple factor for the filtered rectifier circuit below when RL= 4KO. Then explain briefly the effect of changing in the RL value on the output waveform. 5:1 Vp= 0.7v for all diodes Vma 100 V f= 60H2 D S0uF
Please answer in short I will like but please asap please urgent... Consider the circuit shown in the figure. Assume that each diode has a turn-on voltage of V_gamma = 0.6V. a) Determine R1, R2 and R3 such that, ID1 = 0.2mA, ID2 = 0.3mA and ID3 = 0.5mA. b) Find the voltage across V1, V2 and the current for each of the diodes for, R1 = 10kΩ, R2 = 4kΩ and R3 = 2.2kΩ.