included with the kitchen small appliance branch circuits?

Q: Draw the schematic for a simple circuit that gives O/P according to AND gate logic. Determine “V0 ”…

A: AND GATE: Logical expression - Y=A.B TRUTH TABLE: A B OUTPUT (Y) 0 0 0 0 1 0 1 0 0 1 1 1…

Q: 10. Which of the following is true about microprocessors?

A: The correct option along with the explanation is provided in the following section.

Q: State the stages in the ADC (analog to digital converter) circuit and briefly explain each of these…

A: We are authorized to answer one question at a time since you have not mentioned which question you…

Q: Elaborate with Scientific Reason: Briefly explain how a Transistor can be used as a Switch and as…

A: Transistor as a switch: When a transistor works as a Switch it works in Cutoff and Saturation…

Q: How to design your circuit so that no latch-up occurs in your circuit in the event of an ESD?

A: Remedies to avoid latch-up of circuits include, Locating the conflicting components as far as…

Q: 24. Define FACTS and write its necessity and benifits. With neat diagrams, briefly describe…

A:

Q: TTR 300 , what are the features (specifications) of the device ?

A: TTR 300 is known as transformer turns ratio tester it is set of three phase transformer which is…

Q: C) What are the types of gate protection circuit? List advantage and disadvantage of each one? D)…

A: Since both the question are not interlinked as per the guidelines of Bartley we supposed to answer…

Q: Draw the schematic diagram and explain the temperature - resistance characteristics of the RTD.

A:

Q: 1. How are encoders used in the measurement of speed? Explain the encoder with a neat diagram.

A: An encoder is a transducer that is used to measure angular displacement. The encoder can be used to…

Q: Q3: Explain with aid of figures and equations the type of quantization and the quantization error.…

A: The quantization is a process of converting an analog signal into an equivalent digital signal. This…

Q: 2) what is aparallel circuit?what cct. Characteristics indicate that aparallel cct. Condition…

A: Since, you have posted multiple questions. We can answer only one of them. So, i solved Q. 2 for…

Q: Q3) Explain the function of the LOOP instruction and write a small program using it (different from…

A: LOOP instruction is used to perfom repetitive sequence for specific number of times

Q: __________________ is used to convert the low-voltage DC to higher-voltage AC.   Utility grid…

A:

Q: 3. Draw a block diagram of Execution and Bus interface units of 8086 microprocessors.

A:

Q: Define the analog and logic circuits. List the Logic Circuit advantages / disadvantages.

A: An analog circuit is a circuit which gives a continuous signal (continuous in both time and…

Q: i. Draw the circuit diagram of 4-bit Ripple Carry Adder.

A: To draw the circuit diagram of 4 bit ripple carry adder 4 full adders are connected one after…

Q: Discuss the difference between Microcontroller & System-on-Chip

A: The microcontroller is used for a specific purpose, various sensors could be interfaced to it while…

Q: compare the analog voltage divider method for handling switches versus the multiplexer method. In…

A: COMPARISON BETWEEN ANALOG VOLTAGE DIVIDER METHOD FOR HANDLING SWITCHES VERSUS THE MULTIPLEXER METHOD…

Q: Q. How the serial communication is performed in 8086 and draw and explain each block of internal…

A: In serial communication one bit is transferred at a time. Serial communication of 8086 is…

Q: With Neat sketch explain the construction, operation, VI characteristics, application and features…

A: Both BJT and MOSFET have some limitations to be used in very high current applications. So to…

Q: What is the reason for using CRT used instead of LCD or LED displays? a) To meet the required…

A: Given: CRT: CRT stands for cathode ray tube. It is a vacuum tube containing one or more electron…

Q: Draw the constructional diagram of a PMMC instrument and explain its operation in detail. Mention…

A: A Permanent Magnet Moving Coil meter also known as a D'Arsonval meter or galvanometer. It  is an…

Q: Explain ARM Cortex M4 controller (STM32F407) and compare ARM Cortex processors, e.g. M0,M1,M2,M3,M4…

A: ARM Cortex M4 controller (STM32F407) can be defined based on certain characteristics, these are…

Q: wave shapes of a three phase inverter

A: Diode- When diode is forward biased it is short circuited in a circuit ideally.When diode is reverse…

Q: Explain the working principle of LED bulbs used in homes.

A: LED bulbs use principle of electroluminiscence.

Q: ) What is the minimum clock period for the circuit own? D CIk O What are the setup and hold time…

A:

Q: What are the merits of Cockroft Walton voltage multiplier circuit?

A: Given:   Here in this question they are interested to know about the Cockroft Walton voltage…

Q: What are the advantages of using a digital system over an analog one

A: Disadvantages of Analog System- More effect on system by unwanted signal (noise) as it works on…

Q: а. What is an accumulator system, explain with mathematical expression. b. Find whether an…

A: Bartleby has policy to solve only first 3 subparts of a question. For solution of rest questions…

Q: What is an embedded system?

A: In this question , we have to write about embedded system...

Q: 31. Consider the following stick diagram. Draw the electrically equivalent transistor-level…

A: According to the question, for the given stick diagram as shown below We need to draw the…

Q: If Vin exceeded Vref in a real ADC IC, would it actually damage the IC? If not, what would the…

A:

Q: What is the difference between an analog and a digital system? Provide examples that are…

A: Analog system:Analog system process the continuous signals with in the range Example :Audio…

Q: What is the name of the Intel technology that enables a CPU to simultaneously manage two threads?

A: Hyper threading Intel technology ,enables a CPU to simultaneously manage two threads.

Q: Explain How is the inverter type ACU open-loop systems calibrated

A: An open-loop system is a sort of control system in which the system's output is determined by the…

Q: Draw the block diagram of Digital instrumentation system and label the same.

A: In the engineering field, we deal with various types of instruments to record, monitor, indicate,…

Q: Explain the construction and operation of CRO with diagram.(write by computer)

A: CATHODE RAY OSCILLOSCOPE:   CRO is used to display, measure and analyze various types of wave forms…

Q: How can I implement 4035 ic as a parallel input and serial output?

A: For implementation of 4035 IC as a parallel inputs we have to use pin number 9, 10, 11, 12 or Pin…

Q: b) Which type of VFD architecture does require a braking resistor; Voltage Source Controller or…

A: The detailed answer is solved below according to the given parameters and instructions in the…

Q: Give the classification of digital voltmeters. Describe briefly with neat diagrams the working of…

A: In the explaination below I have described the question in an easy way. Have a look at the solution…

Q: Describe with the aid of a diagram how a metal-oxide- semiconductor structure can be used to form a…

A:

Q: transistor logic (discuss)

A: The explanation is as follows.

Q: 1- The thyristor holding current is defined as:* the minimum thyristor current that holds the…

A: there are multiple questions. as you haven't specified which one is to be solved. so I am solving…

Q: Explain the purpose of ASI and CPI testing in VAST deployments.

A: VSAT: A two-way ground system that collects and sends satellite data is called the very small…

Q: For the ALU circuit shown below, what should be the control word (S251SO) to perform the (sl A)…

A: According to the question, for the given circuit as shown below We need to find the condition for…

Wheatstone Bridge Method

A Wheatstone bridge is a circuit used to measure unknown resistance by measuring the ratios of the two branches of the circuit such that each branch has two resistance and out of four resistance one is unknown. The two branches are joined in between with the help of galvanometer which is used to determine the direction of the current. The main advantage of this circuit is that it can provide the most accurate measurement (different from a simple voltage separator).