In this derivable the students need to calculate the output of a summing amplifier. Students have to use the design equations for both inverting and non-inverting summing amplifier. Assume that you need to add the following three input voltages: Vs1 = 0.2 V, R1= 20k Vs2 = 0.4 V, R2= 35kn Vs3 =0.6 V, R3= 40kn Rf= 80kn | Submit (below) a report with the following: 1. Calculate the output with the use of the inverting summing Amplifier 2. Calculate the output with the use of the non-inverting summing Amplifier 3. Compare the two summing amplifiers (inverting and non-Inverting) and write their advantages and disadvantages

In this derivable the students need to calculate the output of a summing amplifier. Students have to use the design equations for both inverting and non-inverting summing amplifier. Assume that you need to add the following three input voltages: Vs1 = 0.2 V, R1= 20k Vs2 = 0.4 V, R2= 35kn Vs3 =0.6 V, R3= 40kn Rf= 80kn | Submit (below) a report with the following: 1. Calculate the output with the use of the inverting summing Amplifier 2. Calculate the output with the use of the non-inverting summing Amplifier 3. Compare the two summing amplifiers (inverting and non-Inverting) and write their advantages and disadvantages

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The screen of a CRT is 60 cm from the centre of the plates. The parallel deflecting plates are of length 2 cm and are 5 mm apart. It has anode voltage of 2400 V. The input is supplied deflecting plates through an amplifier with gain of 20. To get a deflection of 3 cm on screen the input voltage is
In Basic electronics lab on summing amplifier Arifa is asked to give the circuit connectionaccording to figure below to make a three input summing amplifier. She uses IC 741 as OP-AMPand two power supplies to power up the IC. According to the instruction of his teacher she usesthree input such that ?1 = 2?, ?3 = −1? & set ?2 such that the output voltage ?0 = −16.5?. A. What is the virtual ground of OP-AMP?B. Draw the equivalent circuit of OP-AMP and then simplify it for Ideal case.C. Determine the value of ?2 from the figure above for which ?0 = −16.5?.D. If the 50KΩ feedback resistor is replaced by a capacitor of 100uF what will be the outputvoltage after 1 second. Use the value of ?2 = 5 ???(200??)?�
4. Determine the voltage gain of the non-inverting op-amp with Rf-100k and R1=4.7k02. Calculate the output voltage if the input voltage is 200mV
4- For an operational amplifier circuit below. Draw the input and output waveforms if Vin is sine wave with 10 mV,R₁ = 10 KM, and R₂ = 100 KM. VI R₂ www PO
II-1) Draw the circuit of a V-I converter and derive an expression for the output current in terms of input voltage, 2) Draw the neat diagram of analog multiplier using log-antilog amplifiers and explain its operation.
for the common -base configuration using a common value of 30 ohm for the input resistance, input voltage is 200mv and RI=3000 ohm, find the voltage amplification. * 50v 30v 25v 20v
Consider a PV Module with 4 solar PV cells with the Size of each 10cm x 10cm are connected in Parallel. If we connect a lamp load of 2W across this module, choose the correct statement for the above PV Module. (Assume necessary data) a. The output voltage is 0.5V, the output current is 2A b. The output voltage is 0.5V, the output current is 4A c. The output voltage is 2V, the output current is 2A d. The output voltage is 2V, the output current is 4A
What output voltage results in the circuit below for an input of 0.5 V. Refer to the following for the values of Rf = 413981 ohms, R1 = 16788 ohms. Express your answer up to two decimal places. ... V. 360 kQ 12 ko Round your answer to 2 decimal places.
Compute for Zin and Zout. Voltage Gain and Current Gain.
A circuit consist of two cascaded opamp amplifiers, If the gain of first stage is 6.7 and the gain of the second stage is 3. Then the total voltage gain A, is
A piezoelectric force transducer has a charge sensitivity of 20 pC/N. It is connected to a charge amplifier and overall gain of transducer and amplifier is 50 mV/N. The gain of amplifier is O 2.5mV/pC O 1mV/pC O 1.5mV/pC O 4mV/pC
4. A current measuring operational amplifier is made by bridging a resistor across the inverting terminal (pin 2) and the output terminal (pin 6). The noninverting terminal is grounded. a. Draw a sketch of the current measuring circuit. Determine an appropriate resistor for converting a current of 1.0 picoamperes (1.0 × 10-¹2 A) to a voltage of 0.010 V. (The math for this question is very easy, don't overthink this question. b. There are a few reasons that circuit you drew in part a will not be effective. First, you will have a difficult time finding a resistance with the required resistance value. Second, the input terminals do not have infinite resistance value. In fact, for an inexpensive 741 op-amp, the input terminal resistance may only be a few MOhms, which is far less than the resistance your calculated for the feedback resistor. This means that more current will be drawn into the op-amp than will go around it. Finally, the op-amp may have a bias current that is larger than the…