In the following 3-phase power system, the voltage at point a is initially 0.95 pu, and the motoris drawing power 0.95 pu with power factor 0.8 lagging. The reactances are X,and X{ = 0.15 (all per unit).= X = 0.25тILjXajX"jXm+E,EmA ground fault occurs along the dotted line. What is the per-unit fault current?

In this question we need to find a fault current of the given system when a ground fault occurs at…

In the following 3-phase power system, the voltage at point a is initially 0.95 pu, and the motor is drawing power 0.95 pu with power factor 0.8 lagging. The reactances are X, = Xm = 0.25 and X = 0.15 (all per unit). IL jXt jX" jX" + E, A ground fault occurs along the dotted line. What is the per-unit fault current?

In the following 3-phase power system, the voltage at point a is initially 0.95 pu, and the motor is drawing power 0.95 pu with power factor 0.8 lagging. The reactances are X, = Xm = 0.25 and X = 0.15 (all per unit). IL jXt jX" jX" + E, A ground fault occurs along the dotted line. What is the per-unit fault current?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter9: Unsymmetrical Faults

Section: Chapter Questions

Problem 9.13P: Consider the oneline diagram of a simple power system shown in Figure 9.20. System data in per-unit...

See similar textbooks

Similar questions

The negative sequence current of a solidly grounded generator for single line to ground fault is j 2.5 p.u. Then the current flow through the neutral during the fault is j 2.5 pu j0.75 pu j7.5 pu j0.25p.u
In single phase power factor meter there is error due to frequency and waveforms but not in three phase power factor meter, I know the reason why?? Please elaborate properly
Q3/ For the system shown in figure. The generator is supplying 1.0 pu MW power under prefault condition. When three-phase fault occur at point F. What should the value of fault reactance must be to make the critical clearing angle equal to 58.9. Sc j0.1 j0.1 10.21 BE j0.38 38 j0.21 IEgl-12 pu 10.19 F 10.19 IVI-1.00 pu j0.1 j0.1 Q4/ Figure below shows the one-line diagram
In the figure below, all impedances are in per unit on a common MVA base. The generators are operating on no load at their rated voltage. A three-phase fault occurs at bus 1 through a fault impedance of Zf = jo.o8 per unit. Find Vi during the fault in per unit. X, = 0.1 Ooto X 0.1 X =0.2 X-0.1 O a. vi(n=0.4 p.u O b. vif)=0.5 p.u OC V1(0=0.6 pu VI=0.7 p.u
Description In the particular case of figure below derive both the critical clearing angle and the critical clearing time. P, = Pmaz sin d Pm A1 do der Smar A generator having H = 6.R MJ/MVA is delivering power of 1.0 per unit to an infinite bus through a purely reactive network when the occurrence of a fault reduces the generator output power to zero. The maximum power that could be delivered is 2.5S per unit. When the fault is cleared, the original network conditions again exist. Determine the critical clearing angle and critical clearing time. (Roll=PQRS)
• A radial power system network is shown in figure below, a three phase balanced fault occurs at F. Determine the fault current and fault level in MVA under fault condition using a base of 12MVA, 11.8 KV on the generator. 12 MVA G1 Xg1 = 0.12 pu 12 MVA G2) X92 = 0.15 pu 11.8 KV T, 12 MVA, X71 = 0.12 pu Line-1, Zne-1 = (9.45 + j12.6) ohm 33 KV- 3 MVA, x72 = 0.08 pu 6.6 KV Zine-2 = (0.54 + j0.40) ohm %3D Line-2 F
Determine the short-circuit current ISC3,0.4kV for a 3-phase short- circuit fault at F. Give your answer up to 2 decimal in kA but do not enter the unit in your answer. Transformer T1 Transformer T2 Cable C1 Isc3,6.6kV Isc3.0.4kV O + j0.150 F 1 MVA 2 MVA 22/6.6kV 25 MVA fault level 6.6 kV/400V Z=3% 6.6 kV switchboard 400 V switchboard
(9) An unloaded generator with a pre-fault voltage 1 pu has the following sequence impedance: Zo = 0.15 pu, Z₁ = Z₂ = 0.25 pu The neutral is grounded with a reactance of 0.05 pu. The fault current in pu for a single-line to ground fault is (a) 3.75 pu (b) 4.28 pu (d) 7 25 pu
A generator operating at 50Hz delivers 1 pu power to an infinite bus through a transmission circuit inwhich resistance is ignored. A fault takes place reducing the maximum power transferable to 0.5 puwhereas before the fault, this power was 2.0pu and after the clearance of the fault, it is 1.5 pu. By theuse of equal area criterion, determine the critical clearing angle.
Consider the oneline diagram of a simple power system shown in Figure 9.20. System data in per-unit on a 100-MVA base are given as follows: The neutral of each generator is grounded through a current-limiting reactor of 0.08333 per unit on a 100-MVA base. All transformer neutrals are solidly grounded. The generators are operating no-load at their rated voltages and rated frequency with their ENIFs in phase. Determine the fault current for a balanced three-phase fault at bus 3 through a fault impedance ZF=0.1 per unit on a 100-MVA base. Neglect -Y phase shifts.
Even though the fault current is not symmetrical and not strictly periodic, the rms asymmetrical fault current is computed as the rms ac fault current times an asymmetry factor, which is a function of _______.
Equipment ratings for the five-bus power system shown in Figure 7.15 are as follows: Generator G1:Â Â Â Â 50Â MVA,Â 12kV,Â X=0.2 per unit Generator G2: 100Â MVA, 15 kV, X=0.2 per unit Transformer T1: 50 MVA, 10 kV Y/138kVY,X=0.10 per unit Transformer T2: 100 MVA, 15 kV /138kVY,X=0.10 per unit Each 138-kV line: X1=40 A three-phase short circuit occurs at bus 5, where the prefault voltage is 15 kV. Prefault load current is neglected. (a) Draw the positive-sequence reactance diagram in unit on a 100-MVA, 15-kV base in the zone of generator G2. Determine (b) the ThĂ©venin equivalent at the fault, (c) the subtransient fault current in per unit and in kA rms, and (d) contributions to the fault from generator G2 and from transformer T2.