In the figure, two blocks are connected over a pulley. The mass of block A is 6.70 kg and the coefficient of kinetic friction between A and the incline is 0.160. Angle 8 of the incline is 46.0°. Block A slides down the incline at constant speed. What is the mass of block B? Frictionless, massless pulley B Number Units

In the figure, two blocks are connected over a pulley. The mass of block A is 6.70 kg and the coefficient of kinetic friction between A and the incline is 0.160. Angle 8 of the incline is 46.0°. Block A slides down the incline at constant speed. What is the mass of block B? Frictionless, massless pulley B Number Units

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. Blocks B has a mass of 20 kg and block C has a mass of 15 kg. The coefficient of static friction at the contacting surfaces is 0.2. Block A is suspended by a rope that passes over a fixed cylinder and is attached to block B. The coefficient of static friction between the rope and the cylinder is 0.25. What is the largest mass block A can have without causing block B to slip the left? 20
The three flat blocks are positioned on the 30 degrees inclien as shown and a force parallel to the incline is applied to the middle block. The upper block is prevented from moving by a wire which attaches to the fixed support. The coefficient of static friction for each of the three pairs of matting surface is shown. Compute the following: 1. The value of P before any slipping takes place. 2. The maximum value of the friction force between the 40 kg block and the 50 kg block. 3. The tension of the cable supporting the 30 kg block. 30 kg 50 kg 40 kg H=0.30- H₂=0.40 30⁰ -H=0.45
2(b) Problem 9.19 Each box weighs 10 Ib. The coefficient of static friction between box A and box B is 0.24, and the coefficient of static friction between box B and the inclined surface is 0.3. What is the largest angle a for which box B will not slip? Strategy: Draw individual free-body diagrams of the two boxes and write their equilibrium equations assuming that slip of box B is impending
Based on the following figure if the value of F is equal to 2541 N and the angle α is equal to 26.3°. Determine the minimum mass of the block A (in kg) so that it does not slide to the right product of the force F, if it is known that the static coefficient of friction is 0.25 and the dynamic is 0.2.
PROBLEM 5 The uniform block, 4'x 3'as shown weighs 2001b. It is pulled up the incline by the force F= 250 lb. Determine the maximum and minimum values of d so that the block does not tip over as it slides up the incline. The coefficient of friction is 0.21. +3 IL
Calculate the uplift pressure at point C₂ shown in the figure below using Khosla's theory. 5m AH-6m E1 C1 D1 10m USWL E2 C2 3mm D2 20mm v DS BL E3 C3 D3 0.2 m 7mm
Q1- The W=2500-N block shownin Fig. below is in contact with 30° incline. The coefficient of static friction is o.25. Compute the value of the horizontal force P necessary to W P (a) just start the block up the incline or (b) just prevent motion down the incline? 30°
Q4: In Figure below, find the hydrostatic force on the curve AB Oil S=0.9 Тank Cylinder r=1.5m B 2.25 m 3.25 т
P 120 N 200 N 30° 2. Block A weighs 120N, block B weighs 200N and the cord is parallel to the incline. If the coefficient of friction is 0.60 and = 30°. eripit lipwhat force P applied to B acting down and parallel to the incline will elec start motion? What is the tension in the cord attached to A? 2 0837 W
A 10-lb force is pushing the 40-lb block as shown. The incline angle of the plane is α=40º . The coefficient of static friction between the block and the incline is μs = 0.75 and the coefficient of kinetic friction is μk = 0.65. Will the block slide on the plane? If it does, will it slide up or down the plane? What is the friction force between the block and the plane?
4. A 25 mm diameter shaft is pulled through a cylindrical bearing as shown (not rotating). Oil is used as a lubricant and fills the 0.3 mm gap between the shaft and the bearing. The kinematic viscosity of the oil is 8.0 x 10-4 m²/s and the specific gravity is 0.91. Determine the force P required to pull the shaft at a velocity of 3 m/s. Assume the velocity distribution in the gap is linear (i.e. Couette flow). Draw the free body diagram and show the forces. Bearing Shaft 0.5 m- Lubricant
1. Determine the minimum coefficient of static friction us which will allow the drum with fixed inner hub to be rolled up the 17° incline at a steady speed without slipping. What are the corresponding values of the force P and the friction force F? rig 17° 31°