Urgent In the figure, ideal fluid (water) flow from the infinitylarge basin through the atmosphere. Diametersof the pipes for AB, is 0.30 m, BC is 0.10 m and, CD is0.20. The absolute atmospheric pressure is 1kgf/cm?and the absolute vapor pressure is 0.025 kgf/cm².According to given data;0.40m0.10m0.30m0.20mDetermine the discharge of the systemand calculate velocities in each part ofthe system,Determine the possible maximum axialheight of the BC pipe (z) and draw theabsolute and relative (hydraulic) gradelines for this condition.0.00m

Given:- absolute vapour pressure=0.025 kgf/cm2 absolute atmospheric pressure = 1kgf/cm2 AB dia=0.30m…

In the figure, ideal fluid (water) flow from the infinity large basin through the atmosphere. Diameters of the pipes for AB, is 0.30 m, BC is 0.10 m and, CD is 0.20. The absolute atmospheric pressure is 1kgf/cm? and the absolute vapor pressure is 0.025 kgf/cm². According to given data; 0.40m Determine the discharge of the system and calculate velocities in each part of the system, Determine the possible maximum axial height of the BC pipe (z) and draw the

In the figure, ideal fluid (water) flow from the infinity large basin through the atmosphere. Diameters of the pipes for AB, is 0.30 m, BC is 0.10 m and, CD is 0.20. The absolute atmospheric pressure is 1kgf/cm? and the absolute vapor pressure is 0.025 kgf/cm². According to given data; 0.40m Determine the discharge of the system and calculate velocities in each part of the system, Determine the possible maximum axial height of the BC pipe (z) and draw the

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

0.0. I Rd 5. A horizontal Venturimeter with inlet and throat diameters 300 mm and 100 mm respectively is used to measure the flow of water. The pressure intensity at inlet is 130 KN/m2, while the vacuum pressure head at the throat is 350 mm of mercury. Assuming that 3% of head is lost in between the inlet and throat, find, the value of Cd for the Venturimeter and rate of flow.
Calculate the discharge through a pipe of diame ter 200 mm when the difference of pressure head between the two ends of a pipe 500 m apart is 4 m of water. Take the value of 'f' = 0.009 %3D
Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized air in the tank. Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014 *12.9517*99.9358*30.4889*39.5136 What gage pressure p1 in kPa, is needed to provide the given flow rate? *1121 kPa*1692 kPa*1328 kPa*1725 kPa
Sample problem 2: (256) Oil flows from a tank through 150 m of 150mm diameter pipe and then discharges into air. If the head loss from point I to point 2 is 600 mm, determine the pressure needed at point I to cause 17 lit/sec of oil to flow. El. 30 m Air, p-? El. 20 m Oil S 0.84 ఆదిరిదిి 150 m - 150 mm O
Situation 2: The figure shown below shows a pump drawing water from a reservoir and discharging it into the air at point B. The pressure at point A in the suction pipe is a vacuum of 10 in mercury and the discharge is 3 ft³/s. Determine the total head at point A and B with respect to a datum at the base of the reservoir. 10-in-diameter suction pipe 8-in-diameter discharge pipe Pump 15 f 25 ft "T 40 ft
Show complete solutions and figures. The shown tank with an attached manometer contains water unit weight is 9.79 kN/cu.m.at 200oC. The atmospheric pressure is 100kPa. There is a valve located 1m from the surface of the water in the manometer. The valve is closed trapping the air in the manometer, and the water is added to the tank to the level of the valve. Find the increase in the elevation of the water in the manometer assuming the air in the manometer is compressed isothermally. a) 101.3mm b) 92.7mm c) 73.2mm d) 82.4mm e) None
With the pressure meter located at Point B, the pressure of running water at point A is measured. Temperature 20°C and specific gravity of fluids According to N / m3; Ywater =9790 N/m³, Ymercury=133100 N/m³, Yoil =8720 N/m³ a) show The Co-print lines on the figure. b)if the pressure value in B is 87 kPa, calculate the pressure value at Point A. SAE 30 oil Gage B 6 ст mercury 5 cmi Water 11 ст 4 cm
Oil (SG = 0.83) flows at a rate of 200 L/s through a 500m pipe with a diameter of 200mm. The friction factor of the pipe is 0.0225. The pipe slopes down at 10 degrees from the horizontal. Determine the difference in pressure between the start of the pipe to the end of the pipe. A) 287.79 KPa B) 176.36 KPa c) 129.34 KPa D No Answer among the choices E) 238.86 KPa
Problem 2 The containers A and B, shown on the figure, are filled with water, with density Pwater = 1000 kg/m³. The pressure in B H0 0,5m container A is PA= 40 kPa. The two containers are connected 1,5m with inclined U-shaped liquid manometer, with 0,5m an manometric fluid density Pmanometric = 2600 kg/m³. Determine the pressure in container B, considering the shown geometry on the figure. Manometric fluid
Oil (SG = 0.83) flows at a rate of 200 L/s through a 500m pipe with a diameter of 200mm. The friction factor of the pipe is 0.0225. The pipe slopes down at 10 degrees from the horizontal. Determine the difference in pressure between the start of the pipe to the end of the pipe. A No Answer among the choices В 287.79 KPa (c) 176.36 KPa C D) 129.34 KPa E 238.86 KPa
*Homework: The tank is filled with water under pressure (19.62 kPa). The length of tank =2m. an empty cylinder lie along the tank on one of its corner. Find (F, and Fy) 19.62 kPa r=1m/ A 1.5m
3. A hydrometer consists of 8-mm diameter cylinder of length 20cm attached to a 25-mm diameter weighted sphere. The cylinder has a mass of 1.20-g and the mass of the sphere is 12.80g. At what level from the junction of the cylinder and sphere will this device float in liquids having the following specific gravities. a. 0.80 b. 1.0 c. 1.20