Hello sir, please explain and solve this term In rolling process, contact length between roll and workpiece (L) can be approximately determined by:L =R(t, -t)where:R= roll radiust0= initial thicknesstf= final thicknessProve that the above equation is true. Also, explain that through drawing an illustrative figure of rolling.

Answered: Image /qna-images/answer/d7897165-9079-4f7b-ab01-570b404fa275.jpg

Answered: In rolling process, contact length…

In rolling process, contact length between roll and workpiece (L) can be approximately determined by: L = / R(t, =tf) where: R = roll radius t0= initial thickness tf= final thickness

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: What is the Pure Rolling Bodies in The Mechanical Systems and what its application?

A: Pure rolling refers to the rolling process in which no slide occurs. Pure rolling is a mix of…

Q: For a frictionless deformation process the maximum increase in temperature is (Where p is workpiece…

A: During the deformation of a metal, a large amount of energy supplied to the work piece is converted…

Q: If coefficient of friction µ in a rolling process is 0.5 and radius of roller is 1,000 mm, what is…

A: Given, Coefficient of friction = μ = 0.5 Radius of the roller = R = 1000 mm Maximum possible…

Q: 6. You have been consulted to design a draw die system for a wire production facility. The starting…

Q: Show that the true strain rate in extruding a round billet of radius r, as a function of distance x…

Q: If it is desired to reduce the power required for the rolling operation of part (b), what…

A: Given : Roller operation for a workpiece To find : To reduce the power required

Q: During a hot upset forging process the starting diameter of work part is 36 mm, and starting height…

A: Given, Initial radius, r1=18 mmFinal radius, r2=35 mmInitial height, h1=33 mmYf=45 MPaμ=0.2

Q: In a rolling operation using rolls of diameter 500 mm, if a 25 mm thick plate cannot be reduced to…

A: Given data: The diameter of roll is D = 500 mm. The thickness of the plate is t = 25 mm. The…

Q: A brass blank was produced using a force of 25.194 tonnes. The blanking punch radius was measured as…

Q: Explain the difference between Flat Rolling and Shape Rolling processes.

A: Rolling: The process of reducing the thickness of a metal slab is done by rolling. It is done to…

Q: In a multi-pass operation, a round bar of 10 mm diameter and 100 mm length is reduced in…

Q: Discuss the significance of tolerance and allowance in production process? Briefy explain?

A: Tolerance and allowance:

Q: The method of sheet forming in which springback is prevented is called .......... n) With the help…

A: Given :- m) The method of sheet forming in which springback is prevented is called ..........n)…

Q: Show that the true strain rate in extruding a round billet of radius r, as a function of distance x…

Q: In hot rolling process, the following data was collected: N=20rpm, R=20cm, to-40mm, t-35mm,…

A: Given Data: The roller radius: R=20 cm=200 mm The original thickness: to=40 mm The final thickness:…

Q: A hot rolling operation is being carried out on 250 mm wide and 25mm thick low carbon steel…

A: Calculate the final thickness. hf=1-0.2ho =0.8×25 =20 mm Calculate the strain. Strain ε=lnhohf…

Q: In rolling process, calculate the applied torque in (N.m) when w= 600mm, K = 275 MPa, n = 0.10, %3D…

A: Given Data W=600 mm K=275 MPa n=0.1 ho=35 mm hf=29 mm R=373.3 mm

Q: In blanking operation, if the final blank diameter is 200 mm & the clearance is 1.5 mm, then the Die…

A: Answer 8: In the blanking operation, the clearance is provided on the punch not on die so die and…

Q: Q1/ A cuber of the type of open-end đies arranged in a ring, has 66 dies, 32x32x150 mm. a-Calculate…

A: Turning operation is the manufacturing technique that is done on a lathe machine. In this operation,…

Q: In a rolling operation using rolls of diameter 500 mm, if a 25 mm thick plate cannot be reduced to…

A: H=25-20 mm=5 mm R=250 mm Maximum draft for successful rolling per pass is given by, H=μ2R5 =…

Q: The figure below shows a symmetric plane-strain upsetting process. The process may also be thought…

A: The intiallength of the tube is LiLi=2t+t =3tThe final length of the tube is LfLf=2t+2t…

Q: In rolling operation, roll strip contact length is evaluated as

A: In rolling operation, roll strip contact length is evaluated as Answer:

Q: Show that the true strain rate in extruding a round billet of radius r, as a function of distance x…

Q: A 200 mm wide and 42.0 mm thick plate made of low carbon steel is to be reduced in one pass in a…

A: Given: The width of the plate, b1 = 200 mm The thickness of plate initially, t1 = 42 mm The increase…

Q: Two parallel shafts 1 & 2, 11 cm. apart and rotating at 75 RPM and 200 RPM are connected by…

Q: Raw material with an input speed of 3.1 MIS will be rolled to the rolling mill with a plate-shaped…

A: Metal forming is a manufacturing process in which the raw material is deformed plastically to get…

Q: A 250 mm wide strip of 20 mm thickness is reduced to 18 mm in a single pass through a rolling…

A: In a single pass, a 250 mm wide strip with a 20 mm thickness is reduced to 18 mm using a rolling…

Q: The following figure demonstrates the pressure acquired form a direct extrusion process versus the…

A: Given: Extrusion process

Q: 1) According to the slab method, in strip drawing, the axial stress at the die exit needed to cause…

A: The axial stress needed to cause deformation in case of ideal frictionless condition is -…

Q: In hot rolling process, the following data was collected: N=20rpm, R=20cm, to-40mm, 1F35mm,…

Q: the work metal has a flow curve defined by K=300MPa and n=0.2, and the coefficient of friction…

Q: Extrusion is a compression process in which material is forced to flow through a die orific to…

A: Answer True

Q: A 300-mm-wide strip 25-mm thick is fed through a rolling mill with two powered rolls each of radius…

A: Let b =width =300mm h1 =Thickness before passing to roller =25mm h2 =Thickness after passing to…

Q: 27(B). Distinguish the Open die and closed die forging process with its benefits and limitations.

Q: (a) Explain the advantage of corner radii of punch and die in Sheet Metal Drawing Process. (b)…

A: (a) Sheet metal drawing process This is a type of forming process in which metal in the form of…

Q: 7) Which of the following statement is/are 1 correct for extrusion process? i. In extrusion, block…

A: Extrusion is a process in which billet or bloom is forced through a opening which may be of any…

Q: In drawing process, compressive forces are used to reduce the cross section of the workpiece.

A: In the above statement, it is mentioned that compressive force is applied in drawing process to…

Q: The thickness of a metallic sheet is reduced from an initial value of 16 mm to a final value of 10…

A: Data given- T1 = 16 mm T2 = 10 mm D = 400 mm So R = D/2 = 400/2 = 200 mm

Q: In hot rolling process, the following data was collected: N=20rpm, R=20cm, to=40mm, t-35mm,…

Q: In a single pass rolling process using 412mm diameter steel rollers, strip of width 120mm and…

Q: Q2. In a hot rolling process with 60 cm roll diameter and coefficient of friction is 0.75, maximum…

Q: Show that the true strain rate in extruding a round billet of radius r, as a function of distance x…

A: Given:- Radius of the billet = r Distance = x True strain =…

Q: 2. Forging. Based on 18.12 (7th ed.) A cylindrical work part has a starting height of 4 inches and a…

A: Given data: The starting height of the cylinder work part is: ho=4 in. The starting diameter of the…

Q: The shear strength of a sheet metal is 300 MPa. The blanking force required to produce a blank of…

A: Given data: The shear strength of the sheet metal is τ = 300 MPa. The diameter of the blank is d =…

Q: 6) is a sheet metal forming process performed by placing a sheet-metal blank over a die cavity and…

A: Only four multiple questions are allowed to solve.

Q: 21) In sheet metal forming the area to volume ratio is considered to be 22) In rolling, if the…

A: As per company guidelines subjected to solve only three sub parts at a time please repost the same…

Q: H.W Example: A 300 mm wide strip 25 mm thick is fed through a rolling mill with two powered rolls…

A: As per given Question W=300mm Thickness =25mm Radius=250mm K=275mpa Reducced thickness =22mm…

Concept explainers

Basic Thermodynamic Processes

The word 'thermodynamics' can be divided into two words, 'thermo' and 'dynamics'. The word thermo deals with the heat and thermal phenomenon, whereas dynamics deals with forces or external agent that drives the heat flow or aids in the motion of heat.

Question

100%

Hello sir, please explain and solve this term

In rolling process, contact length between roll and workpiece (L) can be approximately determined by:
L =
R(t, -t)
where:
R= roll radius
t0= initial thickness
tf= final thickness
Prove that the above equation is true. Also, explain that through drawing an illustrative figure of rolling.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Manufacturer process A compound die will be used to blank and punch a large rectangle (90x150mm blank dimensions) out of 6061ST aluminum alloy sheet stock 3.5 mm thick. The diameter of inside hole is 25 mm. The aluminum sheet metal has a tensile strength = 310 MPa. Determine the minimum tonnage press (force) to perform the blanking and punching operation (1) assume that blanking and punching occur simultaneously and (2) assume that punching occurs first, then blanking. Take: Ac=0.06
A compound die will be used to blank and punch a large rectangle (90x150mm blank dimensions) out of 6061ST aluminum alloy sheet stock 3.5 mm thick. The diameter of inside hole is 25 mm. The aluminum sheet metal has a tensile strength 310 MPa. Determine the minimum tonnage press (force) to perform the blanking and punching operation (1) assume that blanking and punching occur simultaneously and (2) assume that punching occurs first, then blanking, Take: Ac-0.06
Please give me full explanation in 1hour do it fast A 4-in-thick aluminum slab is 10 in wide and 100 in long. It is reduced in one pass in a two-high rolling mill to a thickness = 3.5 in. The roll rotates at a speed = 12 rev/min and has a radius = 20 in. The aluminum has a strength coefficient = 25,000 lb/in2 and a strain hardening exponent = 0.20. Determine the (a) roll force, (b) roll torque, and (c) power required to accomplish this operation, d) Estimate the GHG emission in an hour for the rolling operation.
Wire is drawn through a draw die with entrance angle a= 17°. Starting diameter is 3.0 mm and final diameter = 2.4 mm. The coefficient of friction at the work-die interface = 0.08. The metal has a strength coefficient K = 205 MPa and a strain-hardening exponent n = draw force in this operation. Why are multiple passes usually required to achieve the desired reduction? (Hint: Observe the draw stress value found in this question) 0.20. Determine the draw stress and Lubricant box Initial wire stock (in coil form) Multiple pass/draft drawing Draw die V2, F V3, F shown in figure. Capstan drum (holds multiple loops of wire) (1) (2) (3)
A hot/cold rolling setup is shown right. The operation first hot rolls a 3/8” thick plate, 12” wide (w), of6061 Aluminum, to an intermediate thickness, then finally through cold rolling, down to 1/4” thick plate.The friction factor μ is assumed to be constant at 0.15 for the hot roll, 0.12 for the cold rolling stage. Thefirst set of rolls operate at 50 RPM. Also ignore any width increase during rolling. CW=13% or .13 What is the plate thickness (mm) prior to the last rolls, t1, if the last set of rollers perform cold work reduction listed below at .13 or 13% Note that 9.52 mm is equal to 3/8 of an inch.
0/ Two thick slabs of 300mm each, the first one is used in cold rolling where μ=0.08 while the second is used in cold rolling where µ-0.5. The mill roll diameter in each case is the same as 600mm. Determine the max draft (reduction) in both cases. Discuss the wide difference in results.
Calculate (1) die pressure distribution and (2) forging force for plane strain forging (open die forging). Assume yield strength of the material is Y, and yielding criterion is von Mises. ho 2Lo h Forged to 2L xdx L 'x+value Note: Assume Zo Constant Plane strain Die pressure distribution h L L Die pressure distribution h MATERIAL L dx -(-1) Friction Hill Y L When 0; =Y P=Y' = Calculate forging force X L dF elemental volume Average pressure
A flat-rolling operation of 250 mm wide alloy stee Calculate roll torque
The team is extruding a billet that is 80 mm long with diameter of 40 mm is directly to a diameter of 20 mm. The extrusion die has a die angle of 75°, see Figure 1. For the work metal, K = 600 MPa and n = 0.25. In the Johnson extrusion strain equation, a = 0.8 and b = 1.4. Remaining billet length 75 Ram pressure, p Do Figure 1: Extrusion process. Determine the following design parameters: (a) Extrusion strain (b) Ram pressure at L = 80, 40, and 10 mm. (c) Draw the relationship between the ram pressure and billet length and discuss the results. What are your recommendations to decrease the required ram pressure?
In hot rolling process, the following data was collected: N=20rpm, R=20cm, to-40mm, t-35mm, C=415MPA, m=0.02, w=60cm, one pass rolling. Find Froll, T and Power.
Questions: 1. Two thick slabs of 300mm each, the first one is used in cold rolling where u=0.08 while the second is used in cold rolling where u-0.5. The mill roll diameter in each case is the same as 600mm. Determine the max draft (reduction) in both cases. Discuss the wide difference in results. = 2. A tensile specimen of the metal of 100 mm is length stretched to a length 157 mm during the rolling process. If the metal has a flow curve with parameters: K = 850 MPa and strain hardening exponent n = 0.30. Determine the average flow stress that the metal has been subjected to during the deformation.
Walk-Through Video Dashboard Note: - You are attempting question 4 out of 12 In a rolling operation, a plate of 2 cm thick and 25 cm wide is passed through a rolling mill having 2 powered rolls. Assume friction was enough for rolling. Thickness of the plate at the end of operation is 1.7 cm. Each roll has a radius of 0.3 m and a roll speed of 0.5 revolution per second. Flow curve has the following values K = 225 MPa and n = 0.15. Determine the power required for driving the rolls.