In order to determine the relative density of a sand sample, its natural moisture content and bulk density were determined in the field and were found to be 7% and 1.61 gm/cc respectively. Sample of this soil were then compacted in a proctor's mould of 1/30 cft. Capacity, at the loosest and the densest states. The following data were obtained. Wt of empty mould = 2100 gm Wt. of mould + soil in the loosest state 3363.6 gm Wt. of mould + soil in the densest state = 3857.4 gm Moisture content of the sample used in tests = 11% Determine the relative density of sand.

In order to determine the relative density of a sand sample, its natural moisture content and bulk density were determined in the field and were found to be 7% and 1.61 gm/cc respectively. Sample of this soil were then compacted in a proctor's mould of 1/30 cft. Capacity, at the loosest and the densest states. The following data were obtained. Wt of empty mould = 2100 gm Wt. of mould + soil in the loosest state 3363.6 gm Wt. of mould + soil in the densest state = 3857.4 gm Moisture content of the sample used in tests = 11% Determine the relative density of sand.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The following results were obtained by testing a sample of clay: water content 25.6%, liquid limit 43.5%, plastic limit 19.1%. From this compute the following: (a) Liquidity Index (b) Plasticity Index (c) Shrinkage Limit
A hydrometer test was conducted on the material passing sieve No, 200 and the results are listed in the table below, The results of sieve analysis on the soil showed that the percentage passing No. 4 was 90 % and that passing No. 200 was 20 %. Estimate the clay size fraction in the soil. Table : Results of hydrometer test diameter (mm) 0.0700 0.0400 0.0150 0.0020 % finer (combined) 19 finer 95 80 16 65 13 45 0.0010 30 6 Select one:
Problem#1: An undisturbed sample of silty sand was brought to the laboratory at its natural water content, and the following measurements were made: Total mass at the natural water content: 1523.6g Mass of oven-dried sample: 1318.3g Total volume of sample: 728.2cm3 Density of the mineral solids: 2.7g/cm3 Calculate the porosity n, void ratio e, volumetric water content 0 and dry bulk density pb.
A liquid limit test on a clay was performed with the following results. The natural water content of the clay is 38% and plastic limit is 21%. Number of Blows 6 12 20 28 32 Water content (%) 52.5 47.1 42.3 38.6 37.5 What is the liquidity index of this clay? (Use Interpolation) Group of answer choices 0.895 0.96 1.08 0.90 Please answer this asap. For upvote. Thanks
The dry unit weight of a sand sample in the loosest state is 13.34 kN and in the densest state, it is 21.19 kN. Its grain specific gravity is 270 and has a porosity of 33% P.S. Sorry for the question can’t fully grasp what was written
Pampanga sand with G, = 2.51 is mixed 26% by weight of water and compacted to produce a cylindrical %3D sample of 48 mm diameter and 96 mm long with 7% air porosity. Calculate the mass that will be required and the void ratio of the sample.
An undisturbed sample of fine sand is tested in the laboratory and found to have a dry mass of 4.63 kg, a total volume of 0.00198 m³ and a specific gravity of 2.70. Other laboratory tests are performed to determine the maximum and minimum density of the sand. At the maximum density, it is determined that the void ratio is 0.35 at the minimum density, the void ratio is 0.95. A. Compute the void ratio of the sand. B. Compute the relative density of the undisturbed sample. C. Compute the dry density in Mg/m³.
Pampanga sand with G, = 2.51 is mixed 26% by weight of water and compacted to produce a cylindrical %3D sample of 48 mm diameter and 96 mm long with 7% air porosity. Calculate the void ratio of the sample.
A clean sandstone core sample with diameter of 3.8 cm and length of 5.6 cm is saturated with a brine. The core was desaturated in several steps, and the resistance was measured at each saturation. The results are as follows: Water Saturation (Fraction) Resistance (k2) 1.000 1.302 0.900 1.695 0.800 2.283 0.730 2.878 0.640 3.775 0.560 5.637 0.480 7.838 0.375 13.175 0.350 17.050 0.300 26 Brine resistivity= 0.74 Qm Archie coefficient =1.03 Cementation factor= 2.2147 (1) Estimate the rock porosity. (2) Determine the saturation exponent. (3) Estimate the amount of oil and brine (in cc) in the core sample when resistivity index is 5. All steps of the calculations should be shown.
A 627-g sample of sand was found to have the following amounts of material retained on each sieve/pan: 3/8 in. = 22 g, No. 4 = 45 g, No. 8 = 96 g, No. 16 = 122 g, No. 30 = 163 g. No. 50 86 g, No. 100 = 51 g, No. 200 = 30 g, pan = 11 g a. Calculate the fineness modulus of the sand. b. Is this sieve analysis valid for acceptance purposes? Explain why. c. Does the sand meet the particle size criteria of ASTM C 33. Fully justify your answer (list and check all relevant criteria from ASTM C33)
The natural water content and in-situ unit weight of a sample of sand above water table are 14% and 119 pcf respectively. The emax and emin corresponding to the loosest and densest states as determined by laboratory tests on dried samples are respectively 0.80 and 0.48. If the particle specific gravity is 2.65, calculate S and Dr.
A liquid limit test on a clay was performed with the following results. The natural water content of the clay is 38% and plastic limit is 21%. Number of Blows 6 12 20 28 32 Water content (%) 52.5 47.1 42.3 38.6 37.5 What is the plasticity index of this clay? (Use Interpolation) Group of answer choices 15.74% 18.99% 18.85% 17.63% Please answer this asap for upvote. thanks