In digital logic design laboratory, you need to use the dc power supply to see the NAND operations by using thediodes. Your laboratory uses AC supply of 120 V (rms) at 50 Hz. You are asked to design a dc power supplyhaving the output, V of 5.45V. This output also can be considered as level 1 oftwo inputs of the NAND gates. Consider the peak voltage of the AC supply is smaller than the PIV of the diodes.ACinput000FPulsated DCStable DCRectifierNAND GATEFig. 1: Block diagram for the signal rectification and NAND gate operationBased on this criterion, prepare the following:i. Identify which circuit is necessary for making the DC power supply from AC supply. Illustrateinput-output signals with appropriate labeling.ii.Use the output of the dc power supply to analyze the NAND operation.

given that AC supply voltage V(rms) = 120 Vfrequency f = 50Hzexpected DC output is VDC =…

In digital logic design laboratory, you need to use the dc power supply to see the NAND operations by using the diodes. Your laboratory uses AC supply of 120 V (rms) at 50 Hz. You are asked to design a dc power supply having the output, V of 5.45V. This output also can be considered as level 1 of two inputs of the NAND gates. Consider the peak voltage of the AC supply is smaller than the PIV of the diodes. AC input 0008 Pulsated DC Stable DC Fig. 1: Block diagram for the signal rectification and NAND gate operation Rectifier NAND GATE Based on this criterion, prepare the following: i. Identify which circuit is necessary for making the DC power supply from AC supply. Illustrate input-output signals with appropriate labeling. ii. Use the output of the dc power supply to analyze the NAND operation.

In digital logic design laboratory, you need to use the dc power supply to see the NAND operations by using the diodes. Your laboratory uses AC supply of 120 V (rms) at 50 Hz. You are asked to design a dc power supply having the output, V of 5.45V. This output also can be considered as level 1 of two inputs of the NAND gates. Consider the peak voltage of the AC supply is smaller than the PIV of the diodes. AC input 0008 Pulsated DC Stable DC Fig. 1: Block diagram for the signal rectification and NAND gate operation Rectifier NAND GATE Based on this criterion, prepare the following: i. Identify which circuit is necessary for making the DC power supply from AC supply. Illustrate input-output signals with appropriate labeling. ii. Use the output of the dc power supply to analyze the NAND operation.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Discuss the pin diagram of any logic gate? Explain how the NAND gate can be used to derive the other logic gates. Discuss the application of diode as positive series clipper positively biased with ideal diode, practical silicon diode. Draw the neat waveform diagrams. Elaborate the working of half wave rectifier with neat diagram and waveforms. Determine the peak output voltage and current in the 4 kW load resistor connected to the output terminals of full wave bridge rectifier, if the transformer secondary voltage is 28 Vrms. Use the practical silicon diode model. Discuss the types of transformers with their applications. Explain with a neat diagram an isolation transformer used for electrical power transmission. Also explain the transformation ratio. Explain the difference between single phase and three phase induction motors with their application in detail. Determine the back emf generated in the dc shunt motor if it takes 250 V, 41 A current while running at full load. Assume…
Diode Logic Gates - OR, NOR, AND, Not, & NAND Circuit diagram and explain it Using this link: https://tinyurl.com/2p8fj34c
QUESTION SEVEN A single-phase bridge inverter is fed from 230 V dc. In the output voltage wave, only fundamental component of voltage is considered. Determine the rms current ratings of an SCR and the diode of the bridge for the following types of loads: (a) R = 20 (b) wL = 29. Find also the repetitive peak voltage that may appear across a thyristor in parts (a) and (b).
Explain this circuits in detail NOT and XOR gate
1) what is the Voltage & Current rating ofTriode for Alternating Current (TRIAC) 2) 5. Are the following statements correct or wrong? Justify your answer.(a) Thyristors are used only for low voltage, low current applications.(b) MOSFETs are used for high frequency applications.(c) BJT is more efficient than IGBT in high power applications.(d) GTO requires very low current applied to its gate to be turn off.(e) IGBT is a voltage driven device.
The gate of a JFET is . . biased Select one: a. forward b. reverse as well as forward c. none of the above d. reverse
I (a) Explain how to construct a NAND gate using Diode & Transistor. (b) Draw the circuit diagrams for three input AND gate using Diodes & using Transistors. Write its Truth Table.
An inductive load is supplied from a single-phase inverter that uses a thyristor and diode. The supply voltage is 100 V. Draw the circuit of the inverter and describe with the help of equation and waveforms, how it can be used to generate AC voltage. Also derive the equation of RMS load voltage.
2) A single-phase full-bridge inverter has a DC voltage source V = 230 V. The rms value of the fundamental component of the output voltage is a- 90 V. b- 207 V. C- 350 V. d- 196 V.
Diode Logic Gates - OR, NOR, AND, Not, & NAND Give Circuit diagram and table and explain it Also site references: P.S. Not hand writing please
Find the RMS voltage expression of output phase voltage of a balanced three-phase square wave inverter need it asap
• Discussion: • How many states the PN sequence generator of DB20 have? • What is the length of PN sequence generator of DB20? • Calculate the outputs of each clock and put them on the Table (2). • What is the PN Sequence of the DB20. • Verify the outputs you get with the outputs from the device.