In a vertical double acting steam engine running at 360 r.p.m, the cylinder diameter is 0.3 m, piston rod diameter is 40 mm and length of connecting rod is 0.7 m. When the crank has moved 120 degree from top dead centre, the pressure of steam at cover end is 0.35 N/mm? and that at the crank end is 0.03 N/mm2. If the weight of reciprocating parts is 500 N and length of stroke is 300 mm, find: (a) Piston effort and (b) Turning moment on crank shaft for the given crank position.

In a vertical double acting steam engine running at 360 r.p.m, the cylinder diameter is 0.3 m, piston rod diameter is 40 mm and length of connecting rod is 0.7 m. When the crank has moved 120 degree from top dead centre, the pressure of steam at cover end is 0.35 N/mm? and that at the crank end is 0.03 N/mm2. If the weight of reciprocating parts is 500 N and length of stroke is 300 mm, find: (a) Piston effort and (b) Turning moment on crank shaft for the given crank position.

Name: In a vertical double acting steam engine running at360 r.p.m, the cyl
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: In a vertical double acting steam engine running at360 r.p.m, the cylinder diameter is 0.3 m, piston roddiameter is 40 mm and length of connecting rod is 0.7m. When the crank has moved 120 degree from topdead centre, the pressure of steam at cover e

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

As shown in Fig., the working area of cylinder head side A=50cm", working load F=10000N, the setting pressure of the valve 1 is 5MPA, and the setting pressures of the valve 2 is 3MPA. e Please answer the following questions: 1) What's the pressure at point A and B respectively when piston of the cylinder is moving forwards at the working speed. Please give the reason. 2) What's the pressure at point A and B respectively when piston of the cylinder reaches and stops at the end. Please give the reason.e To system F A B
Q2 An automotive engine has a bore of 90 mm; the stroke is 110 mm; and the length of the connecting rod is 166 mm Knowing that the volume of the combustion chamber is 75 cm³ and the intake valve closes 18° crank angle degree after BDC. If injection Started 10 degrees before TDC and ends 40 degree after TDC. And the engine is running at 3000 rpm. a. Calculate the geometrical compression ratio and the actual compression ratio? b. Find the ratio between the maximum speed of the piston to the mean piston speed for this engine? c. Find the injection period
There are two double-acting pneumatic actuators, the extension of each one is executed in 5 seconds at 80 psi and recoil in 4 seconds at 30 psi, the travel of both is 12 inches, the diameter of the piston is dp = 4 "and of the rod dv = 1"a) Determine the compression ratios. The local atmospheric pressure is 79kpa = (11.5 psi)b) Determine the air consumption in cubic feet per minute of free air PCMc) Determine the average air consumption for each.d) Propose the regulation values of the pressure switch, system pressure and safety valve
. Two identical cylinders are applied in series as shown in Fig.2. The cylinder piston and rod diameters are 80 mm and 40 mm respectively. The valve is working in position 2. Assuming the tank pressure is 1Bar. . In order to lift the mass 3000 kg in velocity of 0.1m/s, how much pressure in MPa are needed from the motor? • How much volume in liter/min are needed from the motor? 24p CA. ZAP Tips: Q=C₂4 P2 A2 P1 A1 A2 A1 Q1 Q2 MIHIXM Q3
Problem No.4 g exerts no force on the piston when it is at the bottom of the yinder and for the state shown the pressure is 400kPa with volume rise 2 em. ma the newv pressure and spring constant? 1000L-Im |Page2
Q3. Determine the dimensions of an I-section connecting rod for a petrol engine from the following data: Diameter of the piston = 110 mm; Mass of the reciprocating parts = 2 kg; Length of the connecting rod from centre to centre = 325 mm; Stroke length = 150 mm; R.P.M. = 1500 with possible over speed of 2500; compression ratio = 4 : 1; Maximum explosion pressure = 2.5 N/mm.
Patm 1. Initially; the piston sits on the stops and the linear spring exerts no force, the specific volume is 0.05 m /kg and the pressure is 125 kPa. Atmospheric pressure is 100 kPa, mass of the piston is 102 kg, and area of the piston is 200 cm?. The linear spring exerts a force on the piston in such a way that the specific volume becomes 0.08 m'/kg when the pressure reaches 200 kPa. Heat is transferred to the water until its temperature is 115 °C. Calculate work and heat transfer, showing the process on a P-v plot. Hint: In the final stage, the temperature is 115°C, but the pressure is not given. You need to find P and v using the tables and P-v plot.
3- If F = 1x, F = xi, a = wk,, the centrifugal force is equal to a: mw²xî ------- b: -mw²xk c: mw²x k a: 4 d: -mw²xî e: None of them Ś
FIND ONLY (i) THE OVERALL RATIO OF COMPRESSION
Are you Guys Sure? The answer is 14cm? Explain the formulaa please A four-cylinder engine, with a cylinder capacity of 1385.44 cm^3, stroke of 9 cm. Calculate the piston diameter.
(2) a fou-cylinder, 2.4 liter engine operates on a four-stroke cycle at 3200 r.p.m. the compression ratio is 9.4:1, the connecting rod length r = 18 cm, and the bore and stroke are related as S = 1.06 B. calculate :- 3 (a) clearance volume of one cylinder in cm³,L, and in ³. (b) Bore and stroke in cm and in. (c) Average piston speed in m/seca 1 ft/sec
2- Diesel engine, six cylinders is tested at 4750 rpm, the pressure and temperature of the air entering the engine are 1.2bar, and 25 if the bore of cylinder is 80 mm and stroke 120 mm ,take air fuel ratio is 12:1, the specific fuel consumption is 0.52kg/kWh, and the brake power is equal 94 kW find the following: fuel consumption m'f = kg/ sec the air consumption engine capacity.: the flow rate of air intake to cylinder the Volumetric efficiency