In a research lab where ceramics are heat treated for further application, you are presented with two unlabelled specimens (A, B) of bio-ceramics and told that they have the same basic chemical composition, but one has been sintered properly and the other has not been sintered at all. Sample A has larger pore size, and somewhat smaller grains than Sample B. If all ceramics have to be heat treated, which of the specimens need to go into the furnace? Select one: O a. Sample A to go into furnace O b. Neither Sample A nor B to go into the furnace O c. Both Samples A and B to go into the furnace d. Sample B to go into furnace

In a research lab where ceramics are heat treated for further application, you are presented with two unlabelled specimens (A, B) of bio-ceramics and told that they have the same basic chemical composition, but one has been sintered properly and the other has not been sintered at all. Sample A has larger pore size, and somewhat smaller grains than Sample B. If all ceramics have to be heat treated, which of the specimens need to go into the furnace? Select one: O a. Sample A to go into furnace O b. Neither Sample A nor B to go into the furnace O c. Both Samples A and B to go into the furnace d. Sample B to go into furnace

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Given a ceramic material which contains large defects with similar sizes (these defects are small compared to the material), answer the following: 1. Would the strength of the ceramic material be high or low?2. For a set of samples of the ceramic material, would the Weibull modulus be high or low?
Computational analysis has determined that a particular design of glass ceramic component has a maximum allowable tensile stress of 21 MPa Your development team has suggested that a specific grade of Wollastonite with a Youngs Modulus of 99 GPa and a specific surface energy of 0.059 J/m2 may be suitable. What would be the maximum allowable size of any internal pores or defects in the glass ceramic component? (This question has only one correct answer) O a. 8.43 um b. 8.86 mm O c. 8.86 μm O d. 17.72 μm e. 16.86 mm O f. 16.86 μm g. 8.43 mm
In thermal conduction in ceramics and metals, which of the following statements are true? Select one or more: a. Phonons can have arbitrarily high and low energy b. A component of thermal energy is transmitted via phonons c. Phonons are a form of vibrational energy d. Phonons are amplified and strengthened by interaction with lattice defects e. Phonons are scattered and heat transfer reduced with interaction with lattice defects.
EXAMPLE During service, a ceramic valve which is operating at 250°C is likely to be suddenly quenched to room temperature by a flowing aqueous solution. The valve could be manufactured from either of two ceramics, designated A and B, the properties of which are given below. Discuss which ceramic you would select for the application Young's Modulus E (GNm Coefficient of thermal expansion u (K) Fracture Stress , (MNm³³) Poisson's ratio u Thermal conductivity (at 50°C) x (Wm: 'K') 120 2X10 230 0.25 14 B 350 9X104 270 0.27 Ample
Sodium chloride (NaCI) is a ceramic that has the following crystal structure. Given: R(Na*)= 0.098 nm and R(CI")=0.181 Calculate the lonic Packing Factor (IPF) of NaCl? O Na CH Select one: O a. 0.14 O b. 0.66 C. 0.51 O d. 0.74 O e. 0.41 O f. 0.47 g. 0.21
In the appendices, the modulus of elasticity for silicon nitride is 304 GPa (that of steel is 207 GPa). How much porosity could be present in the round bar of silicon nitride such that it equals the reported value for steel?
Young's modulus is a very important mechanical property that can be directly measured by Vickers's hardness test. :Select one True False
A ceramic component with Young’s modulus of 300 GPa and a KIc of 4 MPa.m1/2 is to survive a water quench from 500°C to room temperature of 25°C. If the largest flaw in that material is on the order of 2 μm, what is the maximum value of thermal expansion coefficient (α) for this ceramic required to survive the quench? Assume that there are 20 flaws of 2 μm size. Poisson ratio of the ceramic material is 0.25.
Your supervisor gives you four specimens all of them produced by Lead (Pb), that has atomic mass = 207.2u, atomic number = 82, melting temperature = 327.5 C, and then ask you to make a creep test for all ofthem to know the creep rate and at what temperature will it occur?
Answer the folowing with True or False. Density of a foam material depends on the wall thickness and size of its foam cells. ( ) BCC structure is more densely packed than the FCC structure. ( ) The anion – cation size ratio has an important influence in determining the crystal structure of ionic solids. ( ) CFRP and GFRP are examples of hybrid materials. ( ) The density of a material is determined exclusively by its atomic weight. ( ) Body diagonal in BCC structure has Miller indices of [111]. ( ) The relationship s = Ee is known the Ohms law. ( ) A closed packed triangular plane in FCC crystal has Miller indices of (111). ( )
(Porosity). A dry rock weighs 240 grams and has a bulk density of 2.4 grams per cubic centimeter. When saturated with pure water at room temperature (T=25°C), it weighs 250 grams. At room temperature, specific volume of water is 1.00295 x10-3 m3/kg. Calculate the porosity of the sample. (Permeability). A cylindrical core sample of 1 cm length and 1 cm2 cross-section has upstream and downstream pressures of 2 atm and 1 atm, respectively, during steady state flow of water at 0.997 g/s at room temperature. Calculate the permeability of the core. Note: Water @ 25°C, viscosity = 1 cp, density of water = 0.997 g/cm3. SHOW SOLUTIONS PLS
2. Figure shows the cooling curve for aNiO-MgO ceramic. (b) the solidus temperature 2800 2700 2600 2525 2500 28 2400 10 20 30 40 50 Time (min) Temperature (°C)