"In a R-L series circuit, applied voltage is in phase with the total current." True False "In series-connected ac circuit, the total voltage across the circuit and the voltage across each elements are the same." True False "In parallel-connected ac circuit, the total voltage across the circuit is always equal to the phasor sum of the individual voltage across each element." True False

"In a R-L series circuit, applied voltage is in phase with the total current." True False "In series-connected ac circuit, the total voltage across the circuit and the voltage across each elements are the same." True False "In parallel-connected ac circuit, the total voltage across the circuit is always equal to the phasor sum of the individual voltage across each element." True False

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

15) Kirchhoff's Voltage Law (KVL) states that A) the product of the phasor voltages around any closed path must equal zero. B) the sum of the phasor voltages around any closed path does not have to equal zero. C) the sum of the phasor voltages around any closed path must equal zero. D) the sum of the phasor voltages around a closed path cannot include "through the air."
In a series AC resistive circuit: a) voltage leads current by 90°(degrees). O b) current leads voltage by 90°(degrees). © current and voltage are in phase. d) d current and voltage cancel.
Two impedances consist of resistance of (15 ohms and series connectedinductance of 0.04 henry) and (resistance of 10 ohms, inductance of 0.1 henryand a capacitance of 100 microfarad, all in series) are connected in series andare connected to 230 volts, 50 – Hz AC source. Find: (a) current drawn, (b) voltageacross each impedance, (c) individual and total power factor. Draw the phasordiagram.
A utility company plans to connect a total of 20uF of capacitance to a 7200 volt line. To make this connection four capacitors will be connected in series. What is the capacitance of each capacitor? Answer is 80uF. What is the minimum AC voltage rating of each capacitor? Answer is 1200 volts. What is the current flow through the circuit? And what is the minimum kVAR rating of each capacitor?
4) AC circuit analysis is performed as it was in DC except A) one must use phasors for the voltages and currents and use complex numbers for Impedance. B) one must use phasors for the impedance. C) complex numbers for the V/I ratio are used to represent the power. D) None of the above
Please show you detailed solution Number 10 A voltage of 250 volts at 50 Hz is impressed on a circuit having a 60-ohm resistor, 35-?F capacitor, and a 0.25-henry inductor in series. Determine power factor. A. 0.979 C. 0.924 B. 0.862 D. 0.707
Based on Figures la,1b and 1c and RLC elements, write a discussion on voltage-current relations and power factor.
If T = 0.6Z – 60° and A = 48cm find the position of the first voltage minimum on the line. Select one: O a. The first voltage minimum is at 2cm from the load. O b. The first voltage minimum is at 72cm from the load. O c. The first voltage minimum is at 8cm from the load. O d. The first voltage minimum is at –4cm from the load. O e. The first voltage minimum is at 20cm from the load. O f. The first voltage minimum is at 32cm from the load. O g. The first voltage minimum is at 44cm from the load. O h. The first voltage minimum is at 24cm from the load.
1. A load of 50 ohms resistance and 0.4 H inductance are connected in series to 100 volts, 60 hz a-c source. What must be the value of the capacitance to be connected in parallel to the circuit to raise the power factor to 0.96 lagging. Draw the circuit diagram.
In parallel-connected ac circuit, the value of the equivalent admittance of the circuit is equal to the phasor sum of the individual admittances True or false
An ac resistance is higher than a dc resistance. True False
1. What is the relationship of voltage and current (concerning phase angle) in a pure resistive circuit?