In a heat engine, 3.00 mol of a monatomic ideal gas, initially at 4.00 atm of pressure, undergoes an isothermal expansion, increasing its volume by a factor 9.50 at a constant temperature of 650.0 K. The gas is then compressed at a constant pressure to its original volume. Finally, the pressure is increased at constant volume back to the original pressure. a) Draw a PV diagram to illustrate the cycle for this engine. Label he axes with numerical values. b) find the heat flow into or out the gas during each step. c) Find the entropy change of the gas during the isothermal step.

In a heat engine, 3.00 mol of a monatomic ideal gas, initially at 4.00 atm of pressure, undergoes an isothermal expansion, increasing its volume by a factor 9.50 at a constant temperature of 650.0 K. The gas is then compressed at a constant pressure to its original volume. Finally, the pressure is increased at constant volume back to the original pressure. a) Draw a PV diagram to illustrate the cycle for this engine. Label he axes with numerical values. b) find the heat flow into or out the gas during each step. c) Find the entropy change of the gas during the isothermal step.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

THERMOFLUID Consider a gas undergoing a thermodynamic cycle consisting of three processes from an initial state at P1 = 100 kPa , V1 = 0.81 m3. Process 1 - 2 : constant pressure compression work of 65 kJ,Process 2 – 3 : constant volume heating of 2600 kJ, andProcess 3 – 1 : isothermal expansion. a) Sketch the cycle on a clearly labelled P-V diagram and write appropriate First Law equations for all the three processes. Neglect the changes in kinetic energy and potential energy.
THERMOFLUID Consider a gas undergoing a thermodynamic cycle consisting of three processes from an initial state at P1 = 100 kPa , V1 = 0.81 m3.Process 1 - 2 : constant pressure compression work of 65 kJ,Process 2 – 3 : constant volume heating of 2600 kJ, andProcess 3 – 1 : isothermal expansion. a) Sketch the cycle on a clearly labelled P-V diagram and write appropriate First Law equations for all the three processes. Neglect the changes in kinetic energy and potential energy. b) Determine the:i. volume at the end of constant pressure compression, ii. net work for the thermodynamic cycle, and iii. heat transfer during constant pressure compression.
Problem 4: An engine operating on an ideal Diesel cycle has a cylinder volume when the piston is at bottom-dead-center (BDC), V₁ 1 liter = 0.001 m³. The intake pressure and temperature are P₁ = 300 K. The engine cycle contains the following processes: 100 kPa and T₁ = Adiabatic compression to V₁/24. Constant pressure heating to V₁/14. =
Q1: Select at least five different thermodynamic cycles/processes and make the P-v and T-v phase change diagrams. Also briefly explain the working of each cycle/process.
5. Gas Power Cycle in a Closed System with External Heat Exchange Air in a closed system undergoes the following reversible three-step cycle: 1-2 Isothermal compression of air at T1 = 27°C. The initial pressure is p1 = 2bar 2-3 Isochoric heating to T3 = 1200K . %3D 3-1 Adiabatic reversible expansion to state 1. Consider air as ideal gas with variable specific heats, and gas constant R kJ 0.287 kgK' As you solve the problem, populate the table with the data you need. Use free columns as you like. State T/ p/ v/ u/ h/ 1 2 3 a) Draw the process curve in a p-v-diagram, and in a T-s-diagram. b) Determine the volume V2 = V3 c) Determine work and heat per unit mass of air for each step. d) Determine the thermal efficiency of the cycle. e) The engine runs at 1800 rpm and delivers 12 kW of power. Determine the air mass in the engine and the swept volume. The engine is externally heated, and does not exchange air with the surroundings.
The working gas of a thermodynamic cycle is air. The gas originally starts at 100kPa, 1m³ and 27°C First, the pressure of the gas is doubled keeping the volume fixed. Second, the volume of the gas is doubled at constant pressure. Third, the gas undergoes an adiabatic expansion. Fourth, the gas undergoes an isothermal contraction back to its original state a) Make a table of the pressure, volume, and temperature at the start of each process. b) Make a table of the change in internal energy, heat flow, work done, change in enthalpy and change in entropy during each leg of the cycle. ● ● c) Draw P-v and T-s diagrams, indicating P, V & T at the start of each process & AU, Q, W, AH & AS for each leg. d) Calculate the thermal efficiency of the cycle.
The coefficient of performance for a heat pump is defined as K = - It is a measure of how effective the pump is at extracting heat W (Qin), as compared to the amount of work needed to extract the heat (W]). What is the coefficient of performance for this heat pump?
Draw a schematic diagram of each problem with labels of states of a substance; Assign STATE 1 at the inlet of a high-pressure turbine. The states must be arranged in a chronological order; Plot each cycle in a t-s diagram with thestates consistent to the states assignment in the schematic diagram; A reheat-regenerative Rankine cycle receives steam at 8.0 MPa, 300 0C and exhaust at 0.01 MPa. Steam is extracted at 2.0 MPa for CFWH and the remainder for reheating. The reheated steam enters the 2nd stage turbine at 1.5MPa and expands to 1.0 MPa where more steam is extracted for OFWH. The remainder expands to the condenser pressure of 0.01MPa. Feedwater from low pressure regenerative heater leaves the CFWH at 207 0C and mixes with the feedwater. Determine the percentages of the extracted steam and the cycle thermal efficiency.
Explain the heat transferred from a furnace (Q) to convert the boiler feed water at 25 ° C into superheated steam at 17 bar and 250 ° C.
Q1) Steam is supplied to a turbine at 30 bar and 350°C. The turbine exhaust pressure is 0.08 bar. The main condensate is heated regeneratively in two stages by steam bled from the turbine at 5 bar and 1.0 bar respectively. Calculate masses of steam bled off at each pressure per kg of steam entering the turbine and the theoretical thermal efficiency of the сycle. 1 kg Turbine 1- m- m2 O 1-m, m,- m. Condenser m,. h, m2. 1 kg www kg Drain cooler m2 Heater-1 + (Н.Р.) Heater-2 (LP.)
Q1) Steam is supplied to a turbine at 30 bar and 350°C. The turbine exhaust pressure is 0.08 bar. The main condensate is heated regeneratively in two stages by steam bled from the turbine at 5 bar and 1.0 bar respectively. Calculate masses of steam bled off at each pressure per kg of steam entering the turbine and the theoretical thermal efficiency of the сycle. 1 kg Turbine 1- m- m2 0 1- m, 1- m,-m2 m. h, m2. h2 Condenser 1 kg twwww www meel 1 kg Heater-1 Drain cooler m, m,+ m2 (Н.P.) Heater-2 (L.P.)
Brayton cicle Based on a gas turbine with superheat and intercooling, determine: 1) The thermal efficiency (ƞterm), in %. Use the expression ƞterm= 1 –(qL/ qH)2) How does gas turbine intercooling influence thermal efficiency?3) How and why? It is said that the gas turbine cycle with intercooling, reheating and regeneration is close to the Ericsson cycle.