In a continuous fibre reinforced composite where the fibres are well aligned, the strength in the transverse direction will be the strength in the longitudinal direction. The stiffness of the composite in the transverse direction will be the stiffness in the longitudinal direction. greater than similar to less than

In a continuous fibre reinforced composite where the fibres are well aligned, the strength in the transverse direction will be the strength in the longitudinal direction. The stiffness of the composite in the transverse direction will be the stiffness in the longitudinal direction. greater than similar to less than

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

Sketch and label the expected stress-strain curves at room temperature for lightly cross-linked poly(butadiene) and reinforced poly(methyl methacrylate). Compare the behaviour of each specimen in terms of modulus and toughness.
(b) Compare the thermoplastic and thermoset polymer on the basis of: i. Molecular structure (in the form of sketches) ii. Their behavior upon heating iii. Tensile strength of the engineering stress-strain curve (in the form of sketches) iv. Recyclability
The ingredients in the lamina may be or ... Materials. The laminate composites known as their properties do not vary with direction
name of an aplication in which polymer composite can not be use? and reason why we should not use that composite material in that aplication?
Suggest a structural explanation for why these two polymeric materials have such different glass transition temperatures. Perjant Tg < 0°C sal Tg = = 70°C
Question No. 3 a) Calculate the degree of Polymerization when an average molecular weight of a Polymer is 23040g/mol, having monomer of C8H8O4. b) Calculate the Degree of Crystallinity of the composite having mineral particles of 15(%) by weighthas enthalpy of melting of 31.3 (J/g) and enthalpy of crystallization of 24.4 (J/g). if, Δhm100 = 90(J/g). The Specific gravity of the matrix and particles is 1.24 and 2.2 respectively.
Q.3. Define the following term Frenkel defect, Vitreous clays, Metakaolin, Attrition milling, X-ray diffraction
Which one of the following statements is true for the vulcanization? A It is a process generally applied to engineering thermoplastics. B It is a process of physically cross-linking rubber molecu les with elementalsulfuras widely used crosslinking agent through the action of heat and pressure. It is defined as a process that increases the retractile force and reduces the amountof permanent deformation remainingafter removalof the deforming forces. It provides highly crosslinked polymerstructure and decreases elasticity.
Can embedding nanoparticles of silver intoa polymer give the polymer antimicrobialproperties?
Figure below shows the first four peaks of the x-ray diffraction pattern for copper, which has a face centered cubic erystal structure; monochromatic x-radiation having a wavelength of 0.1542 nm was used. Reflection indices are presented in the table below. The whole number of wavelengths cquals one. (a) Index (i.e., give h, k, and / indices) for each of these peaks. (b) Determine the interplanar spacing for cach of the peaks. (e) For cach peak, determine the atomic radius for Cu. 40.0 50.0 60.0 70.0 80.0 90.0 Diffraction angle 20 Reflection Indices for First Six Planes 110, 200, 211, 220, 310, 222 Crystal Structure Reflections Present (h +k +) even ВСС FCC h, k, and I either all odd or all even 111, 200, 220, 311, 222, 400 Simple cubic All 100, 110, 111, 200, 210, 211 Intensity (relative)
c) Suggest and explain in detail one heat treatment procedure that can strengthen or harden the steel you choose in (a). Sketch the microstructure of the steel after being hardened. Compare the mechanical behaviour of the hardened steel to the plain carbon steel based on their microstructures.
When you shine light of band gap energy or higher on asemiconductor and promote electrons from the valenceband to the conduction band, do you expect the conductivityof the semiconductor to (a) remain unchanged,(b) increase, or (c) decrease?