In a balanced three-phase system, the source has an abc sequence, is Y-connected, and Van = 120/20° V. The source feeds two loads, both of which are Y-connected. The impedance of load 1 is 8+j60/4. The complex power for a-phase of load 2 is 600/36° VA. Find the total complex power supplied by the source.

In a balanced three-phase system, the source has an abc sequence, is Y-connected, and Van = 120/20° V. The source feeds two loads, both of which are Y-connected. The impedance of load 1 is 8+j60/4. The complex power for a-phase of load 2 is 600/36° VA. Find the total complex power supplied by the source.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.42P: A balanced -connected impedance load with (12+j9) per phase is supplied by a balanced three-phase...

See similar textbooks

Similar questions

The three-phase source line-to-neutral voltages are given by Ean=100,Ebh=10+240, and Ecn=10240volts. Is the source balanced? (a) Yes (b) No
1. Given the circuit below, the phase voltages are given by Van = 20040° Vrms. The source impedance is 5 + j7 per phase and the wire impedance is 8 +j10 per phase. Let the load impedance be Zy = 50 ohms. Find: Van Vin Ven a. II, and Ic b. c. VAN, VBN, and VCN, and VAB, VBC, and VCA Z₂ Z₂ Z₂ Zw Zw Zw B C le N
A balanced three-phase Y-connected source with positive sequance has an internal voltage of 120 V/phase. The source feeds a balanced three-phase Y-connected load having an impedance of 39 + j28 N /phase. The impedance of the transmission line connecting the source to the load is 1+ j20/phase. The a- phase of the source is the reference voltage. a) Draw the equivalent per-phase-circuit for the phase "a". b) Calculate the three line currents in the transmission lines. c) Calculate the three phase voltages at load. d) Calculate the three line-to-line voltages at the terminals of the load. e) Calculate the total average power in watts delivered to the load. f) Calculate the total complex power in VA delivered by the source.
Two delta connected loads are connected in parallel and powered by a balanced Y-connectedsource. The smaller of two loads draws 10 kVA at a lagging power factor of 0.75 and the largerdraws 25 kVA at a leading power factor of 0.8. The line voltage is 400 V. Calculate a) The powerfactor at which the source is operating. b) The total power drawn by the two loads. c) The phasecurrent of each load.
Draw a 3-phase wye-connected generator with transmission lines connected to a 3-phase delta-connected load. Assume the lines connecting them have an inductance of j5 per phase. The generated voltages are 120 Vrms with phase 'a' having a phase angle of 0°. The loads are 10 Ohm resistors per phase. When drawing, make sure to label all 3 phases with voltage phasors, line inductances, and load resistances.
The following loads are served by a balanced three-phase source: Load 1: 18 kVA at 0.8 pf lagging Load 2: 8 kVA at 0.8 pf leading Load 3: 12 kVA at 0.75 pf lagging. Give the complex power expression for Load 3. Select one: O a. 29.80 +j13.94 O b. O c. 9.00+ j7.94 kVA 6.40 -j4.80 KVA O d. 32.90225.07° KVA O e. 14.40 +j10.80 kVA
Suppose the DELTA-SOURCE WILL BE CONVERTED TO Y-SOURCE. solve the complex power at the source and load.
The following three-phase circuit is symmetrical, with line voltage 220 V, 60 Hz, direct phase sequence, isolated neutral and the value of the impedances of the loads in the three phases are: Zan = 10 ohms Zbn = -10j ohm Zcn = -10j Ohm Find:a) Phase voltages on the load;b) Line and phase currents;c) The power supplied to the load. Consider the phase voltage in the reference(Va voltage angle equal to 0)
Given three impedances Z, = 10+j0, Z2 = 3+j4 and Zz = 8-j6. Impedance Z, and Zz are connected in parallel and the combination is comnected in series with impedance Z, across 120V single-phase 60HZ source. Find the total power drawn by the impedances.
Problem 3 A balanced three-phase source serves two loads: Load 1: 50kVA with a power factor of 0.60 (lagging) Load 2: 75kVA with a power factor of 0.48 (leading) The line voltage at the "load" is 415.692VRMS at 480Hz. Find the line current in phasor and the combined power factor at the "load." Is the combined power factor leading or lagging?
Q5. A three phase Y-connected load having the following zero, positive and negative sequence Z0 = 8 + j1292, Z1 = 452 and Z2 = 42. Determine the phase impedance matrix of impedances: the load.
Three symmetrical three-phase loads are connected in parallel. Load 1 is connected in Y with an impedance of 400 + j300Ω / φ, load 2 is connected in with with an impedance of 2400 - j1800Ω / φ and load 3 is evaluated at 172.8 + j2203.2 kVA. Loads are supplied from a distribution line with an impedance of 2 + j16Ω / φ. Size of the voltage between the line and the neutral conductor at the end of the charge the line is 24√3 kV. The operating frequency is 50 Hz.(a) Calculate the line currents and the phase currents of the loads.(b) Calculate the total complex power at the receiving end of the system.(c) Calculate the total complex power at the transmitting end of the line.(d) Calculate the values of the compensation capacitors which are connected from the line to the neuron at the load end of the system so that the power factor at the load end reaches pf ≥ 0.98.(e) What if the capacitors are connected from one line to another? What would be the best choice for compensation, the…