im trying to figure out how they got the answer for the modulus of elasticity. the 10.99 is the correct answer im just bot sure how they got it. Measured height at clamped end: 31.75 in Measured height at free end: 30.375 in Calculated deflection: 1.375 in Calculated E: 10.99 x 10^6 psi (provide your calculation details in attached work). Given: m = 189g; Determine Weight= 0.4158 lb Measure L= 36 in Using Weight and Length, calculate q = 0.01155 Ib/in Measure b= 0.996 in; h= 0.120 in Calculate I = 0.000143 in^4

im trying to figure out how they got the answer for the modulus of elasticity. the 10.99 is the correct answer im just bot sure how they got it. Measured height at clamped end: 31.75 in Measured height at free end: 30.375 in Calculated deflection: 1.375 in Calculated E: 10.99 x 10^6 psi (provide your calculation details in attached work). Given: m = 189g; Determine Weight= 0.4158 lb Measure L= 36 in Using Weight and Length, calculate q = 0.01155 Ib/in Measure b= 0.996 in; h= 0.120 in Calculate I = 0.000143 in^4

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question: A rectangular column is shown in the figure, assuming fc'=28Mpa, fy=345Mpa, and e=110mm, calculate the following: 300mm lo Pr O O 10-16 mm O O 0 70mm 70mm 120mm 70mm 70mm 1. stress of outermost tension bars Mpa
5) In the section of the figure below, 6 rebars 36 are used as tensile steel and 4 rebars number 20 are used as compressive steels. Assuming d' is 60 mm and fy is 400 MPa, calculate the anchor of the ultimate cross-sectional strength. 800mm 150mm 750mm 700mm O O 300mm (If there is a lack of problem information for the numerical solution section, make a logical assumption and write it down) The answer must be typed, avoid handwriting. The answer should be short and completely correct, l give a negative score to the answer that I feel is wrong; so please be careful, thank you.
0/10 FIND DEFLECTION IN Aluminum. IF E st= .200000 MPa, Ealu.=70000 MPa 100 kN R ALU.=30 MM Aluminum Steel 0.4 mm 2 mm 0.5 mm 0.25 mm no one 1m_ RST = 20 MM
Question 9 of 20 %3D The figure below shows a shaft of three segments. It is restrained (fixed support) at both sides and is loaded by two torques. Use Goronze = 35 GPa, Galum. = 28 GPa, and Gsteel = 83 GPa. Bronze Aluminum Steel diameter = 25 mm diameter = 50 mm diameter = 25 mm Te =300 N.m< K To -700 N.m A 2 m 2 m 2.5 m Determine the maximum shearing stress developed in steel. Select the correct response. 214.16 MPa 111.79 MPa O 1.75 MPa 57.12 MPa
(40 How A Rismatic steel bar of a Square cro ss section (looxlo0)mm is loaoled by Compressive force P= 1300 K, the bar has length 2.5 m, Eg=200GPay V=0.3,determine the shortening 8, the increase in the dimensions of cross Section, the change in Volume DV of the bar? loomm loomm
1 - An aluminum plate is subjected to uniform stress along its boundaries, as shown in the figure. Determine the change of length of diagonal BD. 120mm 120 MPa 160mm C B V 100MPa -200 MPa E-80GPa ✓=0.3 G=30MPa
a) For the solid section shown in Figure Q1, determine dimensions a, b and c. b) Determine the centroid position (x, y) for the solid section shown in Figure Q1 relative to the origin O on the x-y axes. Clearly show the breakdown of the section into areas used in your calculations. y 85 mm 53 mm b 25 mm 157° 25 mm 65 mm Figure Q1 (Not to scale) X
Locate the centroid y of the cross section. Express your answer to three significant figures and include the appropriate units. y = Submit Part B μA Ir = Value Request Answer Determine the moment of inertia of the section about the z' axis. Express your answer to three significant figures and include the appropriate units. μA Units Value BEL Units 378 ?
Question 28 An A36 angle bar is used as a tension member connected on both legs with 18 mm. Given that s = 74 mm, calculate the design strength (kN) by LRFD with the limiting state of tensile yielding in the gross area. Write your answer to the nearest whole number. |40 50 L6x 3½x% 56 62.5 Ag = 1,852 mm2 t = 8 mm
35 GPa, Gaum 28 The figure below shows a shaft of three segments It is restrained (fixed support) at both sides and is loaded by two torques. Use Gronze GPa and Gre= 83 GPa Steel diameter = 25 mm Bronze Aluminum diameter = 25 mm digmeter = 50 mm T-300 N.m T-700 N.m D 2 m 2 m 2.5 m Determine the relative angle of twist developec between bronze anc alumimu Select the correct response 0:511 rac 05 6 rad 0413 rad 0.005 rac
6. Give the properties table below. A992 Steel 7178 T76 Aluminum Yield Strength 50 ksi 73 ksi Ultimate strength 75 ksi 85 ksi Modulus of Elasticity 29,000 ksi 10,500 ksi Assume you are designing a rectangular member with a specific allowed height. For a design where deflection criterion controls which material would require a larger cross section? For a design where tension stress controls, which material requires the larger cross section?
PROBLEM 2 As shown in the figure, neglecting the weight of the rods and for the loading shown, determine the deflection of point C and of point B A STEEL 3.0 m E=200 GPa d= 38 mm 3.5 m P-60 kN BRASS E=105 GPa 2.0 m d= 25 mm D VQ = 150 kN