Ifthe gap between Cand the rigid wall at D is initially 0.13 mm as shown in Figure 1 and the material has E = 230 GPa, determine i) Force, P at point B such that the gap is equal to zero. ii) Force, P at point B such that the stress acting in BC section is -300 MPa. 650 mm 610 mm -0.13 mm B 25 mm 50 mm

Ifthe gap between Cand the rigid wall at D is initially 0.13 mm as shown in Figure 1 and the material has E = 230 GPa, determine i) Force, P at point B such that the gap is equal to zero. ii) Force, P at point B such that the stress acting in BC section is -300 MPa. 650 mm 610 mm -0.13 mm B 25 mm 50 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.19P: At a point on the surface of an elliptical exercise machine, the material is in biaxial stress with...

See similar textbooks

Similar questions

-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
At a point on the surface of an elliptical exercise machine, the material is in biaxial stress with t = 1400 psi and trv = —900 psi, as shown in the figure part a. The figure part b shows an inclined plane aa cut through the same point in the material but oriented at an angle ft Determine the value of the angle 6 between zero and 90° such that no normal stress acts on plane aa. Sketch a stress clement having plane aa as one of its sides and show all stresses acting on the clement
The state of stress on an element along the hydraulic lift cylinder on a truck is trv= — 5 MPaLFind the maximum shear stress on the clement and show the state of stress on a sketch of a properly oriented clement.
A punch for making a slotted hole in ID cards is shown in the figure part a. Assume that the hole produced by the punch can be described as a rectangle (12 mm X 3 mm) with two half circles (r = 1.5 mm) on the left and the right sides. If P = 10 N and the thickness of the ID card is 1 mm, what is the average shear stress in the card?
A specimen used in a coupon test is shown in the figure. The stresses on element A are known to be sy= -1500 psi. Use Mohr’s circle to: (a) Find the stresses acting on the element oriented at an angle ?? = -35°. (b) Find maximum normal and shear stresses and show them on sketches of properly oriented elements.
The state of stress on an element of material is shown in the figure. Calculate the unit volume change of the element if the stresses x and y. are -20 ksi and 10 ksi, respectively. Assume E = 10,600 ksi and v = 0.33.
Repeat the preceding problem using sx= 5.5 MPa. ??y= 4 MPa. and txy= 3.2 MPa.
-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
Q1. For the given cube below, complete the following: 1.find the center, radius (R), principal normal stresses (σ and σ3), max shear stress (Tmax) and draw the Mohr's Circle. 2. Find the stresses on a plane that is rotated 60° clockwise from the horizontal plane. 6PSE IPSF 10pst 60⁰ TOPST IPSF 6PSF