12.1.2 Part BIf the L-shaped rod has a moment of inertiaI = 9 kg m², F₁ = 12 N, F₂ = 27 N, andagain F3 = 0, how long a time t would it take forthe object to move through 45° (π/4 radians)?Assume that as the object starts to move, eachforce moves with the object so as to retain itsinitial angle relative to the object.Express the time in seconds to two significantfigures. A rod is bent into an L shape and attached at onepoint to a pivot. The rod sits on a frictionless tableF₁3 cmPivot8 cmBMX30°and the diagram is a view from above. This meansthat gravity can be ignored for this problem. Thereare three forces that are applied to the rod atdifferent points and angles: F₁, F2, and F3. Notethat the dimensions of the bent rod are incentimeters in the figure, although the answers arerequested in SI units (kilograms, meters, seconds).

Answered: Image /qna-images/answer/316dbb8e-fc5c-4b28-902e-29610e49c3d8.jpg

If the L-shaped rod has a moment of inertia I = 9 kg m², F₁ = 12 N, F₂ = 27 N, and again F3 = 0, how long a time t would it take for the object to move through 45° (π/4 radians)? Assume that as the object starts to move, each force moves with the object so as to retain its initial angle relative to the object. Express the time in seconds to two significant figures.

If the L-shaped rod has a moment of inertia I = 9 kg m², F₁ = 12 N, F₂ = 27 N, and again F3 = 0, how long a time t would it take for the object to move through 45° (π/4 radians)? Assume that as the object starts to move, each force moves with the object so as to retain its initial angle relative to the object. Express the time in seconds to two significant figures.

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

From the step ladder shown in the figure, sides AC and CE are each 2.44 m long and hinged at point C. Bar BD is a tie-rod 0.762 m long, halfway up. A man weighing 845 N climbs 1.8 m along the ladder. Assuming the floor is frictionless and neglecting the mass of the ladder, find the tension (in N) in the tie-rod.
35.0° Dinysics Demos SuDDly Co. The pole is held horizontally by a massless wire under 305 N of tension, connected at a 35° angle. A 8 kg sign hangs from the end of the 4 meter pole. The pole has mass 4 kg. How far away is the wire is attached from the wall? Answer in meters to 3 sig figs.
Summation of Forces Forces are given; Force 1 = 12 N @ 110° Force 2 = 15 N @260° Force 3 = 5 1 - 6 in 1. Find the resultant force if they are all added? 2. What are the magnitude and angular direction of the sum of the vectors? (Dot Product) 3. F1 o F2= 4. F1 x F3 = (Cross Product)|
An arrangement of two pulleys, as shown in the figure, is used to lift a 69.0-kg crate a distance of 3.83 m above the starting point. Assume the pulleys and rope are ideal and that all rope sections are essentially vertical. P kg F where P = 69.0. What length of rope must be pulled to lift the crate 3.83 m?
Two cones have their heights in the ratio 1:3 and radii in the ratio 3:1. What is the ratio of their volumes?
A rod extends horizontally from a wall. It’s attached to the wall by a bolt at one end, and a wire at the other, as shown. A “SALE” sign hangs from the center of the rod. The rod has W(rod) = 200.0 N and length 3.00 m. The sign has W(sign) = 100.0 N. Find the tension in the wire reported in Newtons.
F, y mg AF f.y F, fx e Axis The ladder in the picture has a mass of 39 kilograms and a length 3 meters. What is the normal force pushing the ladder up from the floor? This force is labeled Ff y in the picture. FN N. %D Assume that the ladder's weight is evenly distributed, so it can be treated as a single force through the middle. If the ladder is at a 69° angle from the ground, what is the torque exerted by the weight (using the floor as the pivot point)? N.m The torque from the ladder must be balanced by the torque caused by the normal force on the wall, labeled Fw in the picture. Calculate this force. Fw - N. The normal force from the wall must be balanced by the friction force from the floor, labeled Ff x.in the picture. Determine the minimum coefficient of friction to keep the
A solid cube of side 2a and mass Mis sliding on a frictionless surface with uniform velocity v as shown in Figure Pl1.50a. It hits a small obstacle at the end of the table that causes the cube to tilt as shown in Figure Pl1.5Ob. Find the minimum value of the magnitude of v such that the cube tips over and falls off the table. Note: The cube undergoes an inelastic col- lision at the edge. - 2a - M a b. Figure P11.50
The mandible (lower jaw) is attached to the temporomandibular joint (TMJ). The masseter muscle is responsible for pulling the mandible upward when you are talking or eating. It is attached at a horizontal distance of about 2.40 cm from the TMJ. The horizontal distance from the TMJ to your incisors is 6.60 cm. If the masseter muscle exerts a force of 198 N on your mandible when you bite into an apple at a constant rate, then what is the magnitude of the force exerted by your incisors on your food, assuming that both forces are vertical?
Problem 5: Fr Fm Bone -Muscle 100 30 cm W 4 cm 40 cm A simplified model of a human arm holding a weight is shown on the right. The length of the forearm is 40 cm and it has a mass of 1.7 kg. The bicep muscle is attached 4 cm in from the elbow joint and makes an angle of 73° with the forearm. The weight in the person's hand has a mass of 5 kg. a) What is the magnitude of the force provided by the bicep muscle needed to keep their arm at rest? b) What is the magnitude and direction of the force acting at the elbow (F;) in that same case?
2. A gymnast with mass 46.0 kg stands on the L. end of a uniform balance beam. The beam is 5.00 m long and has a mass of 250 kg (excluding the mass of the two supports). Each support is 0.540 m from its end of the beam. Answer the following questions. In unit-vector notation, what are the forces on the beam due to support 1 and support а. 2? b. What could be the mass of the balance beam such that the gymnast can just tip the beam at that position?
The human mandible (lower jaw) is attached to the temporomandibular joint (TMJ). The masseter muscle is responsible for pulling the mandible upward when you are talking or eating. It is attached at a horizontal distance of about 2.70 cm from the TMJ. The horizontal distance from the TMJ to your incisors is 6.60 cm. If the masseter muscle exerts a force of 182 N on your mandible when you bite into an apple at a constant rate, then what is the magnitude of the force exerted by your incisors on your food, assuming that both forces are vertical?