By using a Smith Chart, design an L-network to match the load Z = 25 + j300 to a transmission line TLwith Zo = 500 at the frequency f = 1 GHz.jXZo, B(jBY"]ZLZinRemember that we can identify the type of element by using the following table:InductorСараcitorImpedanceZ, = jolZejoc wCAdmittance Y =Y = j@Cjol oL

By using a Smith Chart, design an L-network to match the load ZL = 25 + 1300 to a transmission line…

I By using a Smith Chart, design an L-network to match the load Z₁ = 25+j300 to a transmission line TL with Zo = 500 at the frequency f= 1 GHz. Zo, B Impedance Zin (B)¹ Remember that we can identify the type of element by using the following table: Capacitor Admittance Y₂ = Inductor Z₁ = jooL 1 jol oL jX Z -J = jac ac Yc=jac ZL

I By using a Smith Chart, design an L-network to match the load Z₁ = 25+j300 to a transmission line TL with Zo = 500 at the frequency f= 1 GHz. Zo, B Impedance Zin (B)¹ Remember that we can identify the type of element by using the following table: Capacitor Admittance Y₂ = Inductor Z₁ = jooL 1 jol oL jX Z -J = jac ac Yc=jac ZL

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

7- DC Chopper with output voltage of 120V and input voltage of 80V and output power of 240W. Assume lossless chopper. The average inductance current IL is * 2.6 A 3.0A 4.3A 8- taking into account obtained duty cycle from previous task, the needed : capacitor for realizing 1% ripples at frequency of 10kHz is? * ?? 55.56 uF O 13. 34 uF 92.44 uF
42 Modulation is dune in A. Tramamitter Radio veceiver C. Between transmitter and radio receiver D. None of the above 43. At 100 modulation, the power in each sidehands in AY 50% B. 40% C. 60% D 25% 44 In a TV tranumission, picture is modulated A. Frequency B. Phase CT Amplitade D. None of the above of that of carrier. 45. Given a sine wave modulating signal, PM moduluted wave appears to be frequency modulated by cosine modulating wave. A. True B. False
I turned the voltage value of the AC source into Vrms and got magnitude 16.97 & angle 10.Then calculated the impedance of Load A to be [ -9.28 - j23.4 ]. From that, I calculated the complex power of load B to be [ -2.42 + j6.33 ] my power factor calculation I am using inverse tan ( Q/P) , where Q i got -1.91 & P to be 5.559, which I got from my total complex power. If that helps. But I am calculating a negative power factor, so i am curious where I went wrong, Thank you!
A 502 transmission line is terminated with a 502 resistor on series with a 2 * 10 H inductor. If the frequency of the operation is 60 10° MHz find the reflection coefficient at the load. * Select one: O a. 0.36e56 О .1 O c.0.45e22 O d. 0.6e 37 Oe. 0
A 502 transmission line is terminated with a 502 resistor on series with a 2 * 10 7H inductor. If the frequency of the operation is 60 * 10° MHz find the reflection coefficient at the load. Select one: O a. 0 O b. 0.45e22 O c. 1 O d. 0.36e56 O e. 0.6e-37
A 60-2 transmission line is connected to a 75-2 resistive load. If the incident voltage is 5 V rms, then the reflected voltage is: a) -1.026 Vrms. b) -0.832 Vrms. c) 0.556 Vrms. d) 1.569 Vrms. e) 2.320 Vrms.
b) A 6052 characteristic impedance transmission line is fed by a DC source of 100V with an internal resistance of 4002. The line is 200m long and has a dielectric constant of 2.25. The load impedance is 12002. Calculate: i. The load reflection coefficient. ii. The source reflection coefficient. iii. What is the voltage at the source terminals just before AND just after 2us?
A coaxial cable with a characteristic impedance of 50 Ohm is used to deliver mi- crowave signal to a TV antenna which has an impedance of 75 Ohm. What fraction of the signal (in terms of power) can be coupled into the antenna?
8. A load of ZL-100ohm is connected to a transmission line of 50ohm. the reflection coefficient and SWR are None of them 0.3 and 1.86 0.3 and 0.86 0.3 and 6.81 0.3 and 10.86 9. Calculate the return loss in dB if the voltage load reflection coefficient is 0.24.
11.a. A fiber link has a polarization mode dispersion of 4.2 ps/√km. The fiber link is 5 km. What's the total polarization mode dispersion in this fiber?A. 1.9 psB. 9.4 psC. 0.84 psD. 21 ps 11.b. A transceiver has an extinction ratio of 6 in a fiber link. What's the extinction ratio power penalty?A. 1.5 dBB. 7.8 dBC. 1.1 dBD. 6 dB
b. Determine what is the necessary length and characteristic impedance of a cable to be used as a quarter-wave matching transformer so that it can eliminate the standing waves and subsequently provide a matched condition for a 180 O resistive load fed from a 45 0 transmission line. This condition is to exist for a frequency of 95 MHz. Given a velocity factor = 1.0.
The VSWR on an 50-Ohm transmission line is 5. The distance between successive voltageminima is 80 cm while the distance from the load to the first minimum is 30 cm. What are thereflection coefficient and load impedance