Honeycomb materials are natural or man-made structures that have the geometryof regular hexagonal sheet structure. Theyare widely used in many industries, fromthe aerospace industries, automotive anfurniture, to packaging and logistics. As anewly employed engineer, your task is tocheck if the fabricated honeycombmaterial can be used as package cushion.Given the small portion of the material,determine the magnitude, direction, andpoint of application along AB (measuredfrom A) of force F if the system shown isequivalent to a single force acting at pointO with a magnitude and direction of 120N, 30° E of S. Also, determine theequivalent force-couple at point A. (Note that all measurements are in mm and thatthe direction of F in the figure is just assumed.)24820 N-mm30.060 N1200 N-mm60 N30.085 N25 N10.0

Answered: Image /qna-images/answer/9735af66-d934-44c2-84e9-6213db6c3eaa.jpg

Honeycomb materials are natural or man- made structures that have the geometry of regular hexagonal sheet structure. They are widely used in many industries, from the aerospace industries, automotive an furniture, to packaging and logistics. As a newly employed engineer, your task is to check if the fabricated honeycomb

Honeycomb materials are natural or man- made structures that have the geometry of regular hexagonal sheet structure. They are widely used in many industries, from the aerospace industries, automotive an furniture, to packaging and logistics. As a newly employed engineer, your task is to check if the fabricated honeycomb

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.73P

See similar textbooks

Similar questions

G. A line 32 mm long joins to towns on a map of scale 1:100,000. (a) How far apart are the towns to the nearest km? (b) What length on the map represents a distance of 1.5 km to the nearest mm?
Assuming simple graph of 10 mm grid, draw the isometric views of o bjects shown in fig.1 NOTE :Using catia v5 software only no hand drawing
In (Eigure 1). Fy-700 N and @-20 Figure 30 FA-700 N 1 of 1 Determine the magnitude of the resultant force Express your answer to three significant figures and include the appropriate units. > View Available Hint(s) Fu Submit Part B. Value Determine the direction of the resultant force, measured counterclockwise from the p bitive y axis Express your answer in degrees using three significant figures. View Available Hint(s) Submit Units 15. ΑΣΦ. 11 Ivec Provide Feedback
. Oil drilling rigs are used for drilling holes for identification of oil or natural gas sources and for extraction.An oil drilling system can be thought of as a drillinside a straw, which is placed inside a glass. Thestraw assembly represents the drill string, the drillsurrounded by fluid, and the glass represents thevolume, the annulus, around the drill string throughwhich slurry and eventually oil will flow as the drillingprogresses.Assume that we want to control the drill pressure output, Pd (t), with a reference voltage input,Vd (t). A control loop model (Zhao, 2007) consistsof a drill-pressure controller, drill motor subsystem,pulley subsystem, and drill stick subsystem. Theoutput signal of the latter, the drill pressure, Pd (t),is measured using a transducer, which transmits anegative feedback voltage signal, Vb(t), to the drillpressure controller. That signal is compared at theinput of the controller to the reference voltage, Vr(t),Based on the error, e(t) = Vr (t) – Vb(t),…
SHEET 1: 1. Sketch a cube. All inclined lines are 30° with respect to the horizontal. 2. Fill out these spaces with four-centered ellipses. 3. Draw the center lines for each ellipse. 5 cm x 15cm x15 cM CUBE =0.2 ElLIPSE = 0.2 REST = PENCIL Note: The cube and the center lines are thin lines, while the ellipses are thick.
Two students decided to print a prototype for a gear. Student A use layer thickness of .1 mm and an infill density of 25%. Student B use a layer thickness of 0.07 mm and an infill density of 45%. Which student will take less time to print the gear? Select one: Stu nt since the ckness of layer is smaller and the infill density is higher. O We can't decide which process takes less time O Student A since the thickness of the layer is larger and the infill density is lower. Student B because thickness is higher than B and the infill density has no effect on the process speed. Student A because thickness is higher than B and the infill density has no effect on the process speed.
Answer is Around 5.8lb [diagram must be drawn] An automobile weighing 3900 lbs has 29-inch diameter wheels. Assuming the coefficient of rolling resistance between the tires and the road of 0.02 inch, determine the force necessary to overcome rolling friction on a level road. Answer should be in lbs
Answer part (iv) and (v)
What are the types of irregular grids ? Support your answers with relevant diagrams.
Hello, pls help me identify the OBLIQUE SECTION VIEW of this figure, please include measurements thank you.
Draw isometric view of frustum of the square pyramid with 45 mm base edge, 25 mm upper edge and height 50 mm. (please also explain step by step, with all the dimensions)
two cylinders are printed on a 3d printer, with a setting of 40% fill rate. This means that the solid parts of the cylinders at 40% plastic material. Given this, tell me how much plastic material is used to make each of these cylinders. I measured both cylinders in meters and these are the measurements below A) Cylinder 1- Height: 0.042m Radius 2(outer radius): 0.008m Radius 1(inner radius): 0.006m B) Cylinder 2 Height: 0.022m Radius 2(outer radius): 0.008m Radius 1(inner radius): 0.006m