Quizel-2d sem ester 2021-2022 M oming)W hen the galvanized hon sheets aom e with dim ensions (2x1)m.Cakulate the num ber of sheetsequined to made the ectangular duct system shown in figue below when it sized using equalfriction m ethodwith frictional pressure diop of 1pam and alow able height is 300 mm.0.6 m /s0.6 m/sD 2m2m2m F2mFanC.E2m BA5m

Given data-→Dimension of galvanised sheet=2×1m→Frictional pressure drop=1 paln→Allowalbe height…

- hen the galvanized ion sheets com e w ith din ensions (2x1)m.Calulate the um ber of sheets equhed to made the ectangular cuct system shown in figure below when it sized using equal dction m ethod w ith frictional presure diop of 1pan and alow able height is 300 m m. 0.6 m /s 0.6 m/s D 2m 2m 2m F 2m

- hen the galvanized ion sheets com e w ith din ensions (2x1)m.Calulate the um ber of sheets equhed to made the ectangular cuct system shown in figure below when it sized using equal dction m ethod w ith frictional presure diop of 1pan and alow able height is 300 m m. 0.6 m /s 0.6 m/s D 2m 2m 2m F 2m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

W hen the galvanized ion sheets comewith din ensions (2x1)m.Calulate the num ber of sheets required to m ade the rectangular duct system shown in figure belbw w hen it sized using equal friction m ethod w ith frictionalpressure drop of 1pam and alow able height is 300 mm. 0.6 m /s 0.6 m/s 2m 2m 2m F 2m Fan 2m B 5m
Dete: Pags: of water with lsteability Jwith tembexatura: ange behavioug chosoge
If the compression ratio is 17:1, the piston displacement volume for 10 cm³ piston clearance volume is. Ans. 160 cm³
A of 0.06 melrar, nuns into a taukh tabe The tabe inclu des a Under yoressure, Valve, a wreneh, a el bow The abrupt flicient are and an inlet, minon los coe E he E lhz = G.9 . Friction has grouped as been calculoted as The =002. faucet is pe quired to provide am ain low of 10/s Deter mine the pressure needed in the waten tanth to supply this f low.
O WHATSAPP now Malek @ MENG370 Lab - Spring "O A aw D T me Te T00... Not yet answered Question 7 Marked out of 10 In ideal case and knowing that the area of the Venturi at the inlet and outlet is the same, the pressure head at the inlet and outlet of the Venturi will: Select one: a. Remain constant b. It depends on the velocity of water c. Increase d. Decrease Clear my choice Not yet answered Question 8 Marked out of 10 II
Q: Prediet the manometer reading after (4.45N) weight is placed between piston f cylinder. on the pan. Assume no leakage or friction Pan 37.5 25mm dia. mm dia. oil 600 mm Szo-92 25mn dia. -Hg CB) 4 Sc) in figurs belew are closed
An orifice of diameter 150 mm is fitted at the bottom of a boiler drum lenth 6 m and of diameter 2 m. The drum is horizontal and contains water up to height of 1.8 m. Find the time required to empty the boiler. Take Cd=o 0.60CHOICES a.127 seconds b.175 seconds c.217 seconds d.467 seconds
2- For the tank shown (3m diameter), find the time required to make water reach at mid- height of cylinder. Cd-0.6 & orifice diameter =50mm. AIR p=7.348 Niom T H15m
Problem 4: The U-tube manometer is also widely used to measure the difference in pressure between two containers or two points in a given system. As an example a manometer connected between containers A and B is shown in Figure. Pipe A is filled with the diesel fuel has a specific gravity Yadiese fae -8.326 kN/m and pipe B filled with engine oil has a specific gravity Yengine oi -8.955kN/m³’ If the pressure in pipe A is 105.49kN/m2 Determine the pressure at B. ( Ymercuy =133kN/m) (Munson and Young, 1998) air 0.076m 0.127m D' 0.4572m Diesel fuel engine oil 0.1524m mercury 0.1778m
QV: a hydraulic press is used to compact powdered samples. The device is made of two interconnected cylindrical chambers filled with oil if density psubscripto anc closed by two pistons. The small chamber on the right has diameter d and the large chamber on the left has diameter 5d. A lever is attached to the piston pushing down on the fluid in the small cylinder. The horizontal lever is hinged on the left, at distance L from the small piston, and a force of magnitude Fsubscript0 is applied vertically down at distance 2L from the hinge (Fig.5). You may assume that the lever and pistons have negligible mass. a. Determine the magnitude of the force Fin that the small piston exerts on the fluid in the small cylinder. Hint: you may consider that the lever is at rest in the horizontal position. b. Determine the pressure change applied to the fluid by the small piston. c. Determine the magnitude Fout of the force that the fluid applies to the large piston.
20 cn. During Problems: ) A GO cm vonturi has a a 10 min. tcst it discharged G10 cu pressure head at throot of with and throat diameter a meon at the water the large section of 34 a negative pressure corresponding to 26 trie metor coefficient- an of mercury. Corpute P. as shon. o is floning upivard through a vanturi meter Assume a di schorge cocfficient of rate O. 984. What is the of flow of the oil ? (solution at the back of page 24) S0 mm -200 mm foi (o 02) Elycerine (1. 26)
HELP PLEASEEE, WITH COMPLETE SOLUTION THANK YOUU