he band-pass filter in the figure is required to pass signals with a frequency of f = 39 kHZ with a tolerance of 10% (For example, for a 100 kHz operation, the low cut-off frequency so = 90 kHz and the high cut-off frequency f on ccordingly, when R G1 = 470 2, R G2 = 560 0, RE1 = 1.2 kQ, R2 = 2 ko, C, = 0.05 µF and C; = 0.03 µF, what should the values of the R, and R2 resistors be, respectively? (Op-amps would be considered ideal.) Rçi Rc: Rr: R: RI O a. R1 = 154.17 Q and R2 = 74.20 2

he band-pass filter in the figure is required to pass signals with a frequency of f = 39 kHZ with a tolerance of 10% (For example, for a 100 kHz operation, the low cut-off frequency so = 90 kHz and the high cut-off frequency f on ccordingly, when R G1 = 470 2, R G2 = 560 0, RE1 = 1.2 kQ, R2 = 2 ko, C, = 0.05 µF and C; = 0.03 µF, what should the values of the R, and R2 resistors be, respectively? (Op-amps would be considered ideal.) Rçi Rc: Rr: R: RI O a. R1 = 154.17 Q and R2 = 74.20 2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

SNR is defined as a ratio of O noise power to samplng-ffequency signal power to noise powér signal power to signal BW O noíse power to signal power
92 ۱ ۹:۱ ص Qs= 1107 and Qp= 1041 Qs= 1207 and Qp= 1241 Qs= 1007 and Qp= 1041 Qs= 1107 and Qp= 1141 In the figure shown below we can find output current is equal to.. . if the input voltage is equal to 12 mv 12 kO 12 ka 6 ka No option is correct 10 = 32 uA 10 = 34 uA 10 = 38 uA 10 = 36 uA In the fig. shown below we can find the higher critical frequency due to the input
Problem D continued b. Determine Vout for the given input signal SIG Rx 20k Ry 5k Vcc o- Vcc/-Vcc +10v/ -10V VOUT -Vcc Rx Ry VREF VSIG (t) 6V -6V VOUT (t)
Q3/ Determine the centre frequency, maximum gain, bandwidth and type filter for the circuiting figure. 1 kOhm 0.022 UF HH 0.047 uF 0.047 UF 1 kOhm 1 kOhm Vo HH HH 560 Ohm 560 Ohm 0.022 UF 1 kOhm 1 kOhm Kohm
Q3/ Determine the centre frequency, maximum gain, bandwidth and type filter for the circuiting figure. 1 kOhm 0.022 UF HH 0.047 uF 0.047 UF 1 k Ohm 1 kOhm vo HH HH 560 Ohm 1 Hohm 560 Ohm 0.022 UF 1 k Ohm 1 kOhm
What is the difference between bandwidth and bitrate in optical communication engineering
Anti-aliasing filter ensure that are no frequency components greater than entering the system O a. fs/2 O b. 2/fs O c. 2fmax O d. 2fs
is samples per second. 12. A complex low-pass signal has a bandwidth of 200 kHz. What is the minimum sampling rate for this signal? 13. A complex band-pass signal has a bandwidth of 200 kHz. What is the minimum samnling
16)What is the magnitude of gm for a JFET when IDSS=6mA and VP= -3V at the DC biasing point when VGS= -2V? -1.33mS 1.33mS -2mS 0.44mS
%3D ban d pass filter if f.= 500H2 and For uf2= 1000 Hz a
Question 1: Design the Feed-back bias circuit shown below. Vcc = 3V, Ic = 3 mA, Vc = Vcc/2, VBE = 0.7 V, and ß = 100. IB = I2. (hints, Fined RC, RB1 and RB2). Vcc Rc oVc R Ry2
What is the difference between bandwidth and bitrate In optical fiber